Stainless Steel Housing Series Quick Installation Guide Rev. 1.
UNPACKING: Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears damaged in shipment, place it properly in its carton and notify the shipper. IMPORTANT!: 1. Read and follow Instructions: All operating and user instructions should be read and followed before the unit is to be operated. connections.
English II Swivel Positions and Directions 460.0 mm(18.11") 154.5 mm(6.08") 163.5 mm (6.43") Dimensions 370.0 mm (14.56") 172.0 mm (6.77") 401.1 mm (15.79") 88.0 mm (3.46") 86.0 mm (3.38") 245.0 mm (9.64") 130.4 mm(5.13") 460.0 mm(18.11") (2.97") 75.7 mm 29.9 mm (1.17") 172.0 mm (6.77") 370.0 mm (14.56") 401.1 mm (15.79") 245.0 mm (9.64") 88.0 mm (3.46") 69.0 mm (2.71") 242.5 mm (9.54") (3.62") 92.0 mm 149.5 mm (5.88") 119.9 mm (4.72") 346.0 mm (13.62") 358.0 mm (14.
Dimensions with the IR unit and wiper 130.4 mm(5.13") 460.0 mm(18.11") (2.97") 75.7 mm (3.62") 242.5 mm (9.54") 92.0 mm 149.5 mm (5.88") 119.9 mm (4.72") 29.9 mm (1.17") 370.0 mm (14.56") 401.1 mm (15.79") 172.0 mm (6.
English AE-510-I 24VAC Power distribution board Terminal block Wiper VAIR module Camera Mounting Platform 5
IV Installation Suggestions WARNING: • When install a housing with an IR illuminator: Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared protection glasses, when working with the product. Always use camera live view to oberve IR lighting effects. V Installation 1. How to open the housing Slide out the rear cover plate of the housing, taking care to leave the sealing washer in its seating. Heater or wiper or VAIR connect need unplug.
Ethernet cable Ø4 ~ 6.5mm Power wires Note that some cables are connected when shipped. You do not need to connect heater, blower, and the front IR powere wires. IMPORTANT: 1. Recommend to cover the ethernet or power cable with stainless steel tube in order to prevent the corrosion of cable. You may need to remove the RJ45 connector, and use a crimping tool to connect the Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable of the width of 5 ~ 6.5mm.
4. Assemble the camera components, e.g., the CS ring and lens module. Secure the mounting plate to the bottom of the camera (the label side) using the included screw. 5. Connect 24V power source to the power input terminal. Connect power wires from the DC 12V output to the camera. Below is the distribution board drawing power from 24V AC.
English AE-510-I I/O terminal block 24V AC OUT Heater + - 24V AC IN Power LED 12V DC OUT Blower IR angle selector Connectors to the front IR Below is the pinouts for the DI/DO terminal block: Facing the rear side of the housing, from left to right: DO2 DI2 RS485+ RS485DO+ DIDO1 DI1 Connect to tank water pump. Wiper control, connects to IP camera's DO for manually triggering washer. RS485+, RS485 can be used to control IR illuminator beam angles, etc.
DIP Switch : LL LH HL beam angle for different effective illumination range. VAIR no.
(AE-510-I) 1. IR control by IR Light sensor The below connection enables the synchronization of IR light sensor and auto day/night switch on the camera AC/DC pwr AC/DC pwr RS485+ RS485- DI- DI3+ DI2+ DI1+ DI1 DO- IR ctrl DO1 DI- DO+ IR LED GND RS485+ DO2 DI2 DO+ 5V VCC RS485- Tank ctrl Wiper ctrl Camera Terminal Block Enclosure Terminal Block AWG26 AWG20 DC12V AC24V 2.
3. IR control by Camera DO Camera will automatically trigger IR light on/off via DO. AC/DC pwr AC/DC pwr RS485+ RS485- DI- DI3+ DI2+ DI1+ DI1 DO- IR ctrl DO1 DI- DO+ IR LED GND RS485+ DO2 5V VCC DO+ RS485- Tank ctrl Wiper ctrl DI2 Camera Terminal Block Enclosure Terminal Block AWG26 Below is a diagram for water tank and wiper control. The wiper can be started by manually triggering the Digital Output from the camera user interface.
The front end of the slider is about 70mm from the window. Please install the camera in the appropriate position. 70mm type of installation & plug heater or wiper or VAIR connector to power board. AE-510-I: Heater Connect VAIR Connect AE-510: Heater Connect Plug Plug Install wall mount bracket or Cardan joint bracket. Wall mount bracket mounting Cardan joint Bracket mounting 13 English 7.
8. Sunshield mounting: 9. The housing can also be installed using the pole-mount or corner-mount.
English 10. Open a web console with the camera. Use the Media > Focus function to tune for a best image focus on your target area. If preferred, e.g., shooting fast moving vehicles, select the 60fps frame rate.
synchronized with the digital input you connected. In the night mode, check if the input signals are correctly detected. You may simulate the night mode by blocking the IR unit's light sensor. Change the triggering parameters when necessary.
English VI Appendix: RS485 Commands For housings that come with IR illuminators, wiper, and washer, commands can be delivered via the RS485 protocol. The RS485 connection uses the Pelco D protocol. Baud rate Data bits Parity Stop bit 2400 8 None 1 Command format: Byte1 Sync Byte2 Addr Byte3 CMND1 Byte4 CMND2 Byte5 DATA1 Byte6 DATA2 Byte7 CKSM Addr range: 0x00 ~ 0xFE. CKSM: check sum is the last 8 bits of the sum of Byte2 through Byte6.
LightSensorGate FF 01 00 18 03 LL CKSM For example, IRmode_Auto FF 01 00 18 02 02 1D IRmode_DI FF 01 00 18 02 03 1E IRmode_CMD FF 01 00 18 02 04 1F When the IR Mode Light Sensor Auto, the Lux value to turn IR LED can be LL: Lux, changes is made by every10Lux For example: LightSensorGate = 100 FF 01 00 18 03 0A 26 LightSensorGate = 200 FF 01 00 18 03 14 30 The parameters of IR illuminator can be controlled via the RS485 connection. You can > PTZ > Mechanical window.
VaIR: The VAIR control include those on the IR Led and VaIR Lens.
This page is intentionally left blank.
