User's Manual

ManualsBrandsViVOtech ManualsElectronicsCard Reader

Table Of Contents

ViVOpay 3000 Installation Guide for VeriFone Ruby
- May 2004 Version 1.0
  - VeriFone Ruby Installation Guide

Part number: 600-1030-00

ViVOpay 3000 Installation Guide

for VeriFone Ruby

May 2004 Version 1.0

ViVOtech®, Inc.

451 El Camino Real

Santa Clara, CA 95050

Ph: 408.248.7001, ext.105

Email: info@ViVOtech.com

www.vivotech.com

Summary of content (8 pages)

PAGE 1
A ViVOpay 3000 Installation Guide for VeriFone Ruby May 2004 Version 1.0 ViVOtech®, Inc. 451 El Camino Real Santa Clara, CA 95050 Ph: 408.248.7001, ext.105 Email: info@ViVOtech.com www.vivotech.
PAGE 2
Copyright 2004, ViVOtech, Inc. All rights reserved. ViVOtech, Inc. 451 El Camino Real Santa Clara, CA 95050 Phone: (408) 248-7001 Written and designed at ViVOtech, Inc. This paper, as well as the software and hardware described in it, is furnished under license and may be used or copied online in accordance with the terms of such license. The content of this paper is furnished for information use only, is subject to change without notice, and should not be construed as a commitment by ViVOtech, Inc.
PAGE 3
VeriFone Ruby Installation Guide 1 The ViVOpay 3000™ patent-pending Dynamic Strip™ technology enables contactless payments without hardware or software changes to existing POS devices at minimum cost. This document assumes that installers are familiar with their host POS system. NOTE: It is highly recommended that you review the procedure at least once prior to exposing the adhesive mounting tapes.
PAGE 4
It is important that these areas be clean of any oily or greasy residue that will interfere with the adhesive mounting tapes. Allow the terminal to air dry. 2. Power up the ViVOpay unit in strip test mode Connect the Dynamic Strip cable to the back of the ViVOpay unit. Connect the AC adapter into an AC power outlet. Simultaneously press the button at the rear of the reader with the pencil and insert the power connector from the AC adapter into the socket on the back of the ViVOpay unit.
PAGE 5
b. While in the card-reader test mode, the terminal will display the track data being transmitted from the magnetic card or Dynamic Strip being used on your terminal. NOTE: If the Ruby does not have an application loaded, press 4 twice. c. Plug the power cables into the power ports on the Ruby device and the printer. d. Connect the printer to the Ruby. The coiled cable plugs into the printer's COM4 port on the back of the Ruby. e. Plug power supply cable into an AC outlet. f. Wait until the Ruby boots up.
PAGE 6
When the Strip is correctly positioned, the screen on your POS terminal will display data for Tracks 1 (top) and 2 (bottom). Mark each side of the Dynamic Strip with a pencil. You now have a range where the strip transmits data correctly. NOTE: There may be multiple ranges where data is displayed correctly on the screen. If this happens, select the middle range. If Track 1 data and Track 2 data display in different locations, select the location that displays Track 2 data.
PAGE 7
Carefully position the strip into the slot exactly in the middle range of the two pencil marks. When the strip is in position where the POS readings are successfully displayed, press the top of the strip against the terminal to ensure the adhesive holds tightly. 6. Verify the installation and terminate the test The Strip is correctly installed if your POS terminal continues to display successful readings after the Strip has been affixed. Re-start the ViVOpay by removing and reinserting the power plug.
PAGE 8
Press the Strip cable into the clip. Position the clip on the right side of the POS terminal to guide the cable to the back of the POS terminal. Press the clip down to adhere it in place ensuring the cable is routed away from areas where it may be snagged. Installation is now complete. 8 VeriFone Ruby Installation Guide V 1.