Z1V USER MANUAL
TABLE OF CONTENTS Important Safety Information ...................................... 4 Symbols Used ..................................................................................... 4 General Safety Information .................................................................. 4 Qumi Z1V Installation Notice ................................................................ 5 Power Supply Safety ........................................................................... 5 Cleaning Qumi ..................
Adjusting the Focus........................................................................... 18 Playing Video From a Storage Device (USB Flash Drive, microSD Card) 19 Viewing photos From a Storage Device (USB Flash Drive, microSD Card) ....................................................................................................... 21 Playing Audio From a Storage Device (USB Flash Drive, microSD Card) 23 Playing From a Video Source (HDMI) .................................................
IMPORTANT SAFETY INFORMATION ! IMPORTANT: It is strongly recommended that you read this section carefully before using Qumi Z1V. These safety and usage instructions will make sure you enjoy many years of safe use of Qumi Z1V. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following symbols are used to call attention to important information.
Qumi Z1V Installation Notice Allow at least a 500mm (20”) clearance around the exhaust vent. 500 mm (20 in.) Make sure that the intake vents do not recycle hot air from the exhaust vent. When operating Qumi Z1V in an enclosed space, make sure that the surrounding air temperature within the enclosure does not exceed the operating temperature while Qumi Z1V is running, and the air intake and exhaust vents are unobstructed.
REGULATORY COMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
INTRODUCTION About this Manual This manual is intended for end users and describes how to install and operate Qumi Z1V. Wherever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.
PACKAGE CONTENTS Qumi Z1V Remote Control Adapter Carry Bag Documentation 8
YOUR PROJECTOR Front-Left View 1 4 2 3 1 Front IR Sensor 2 Lens 3 Front Speaker 4 Focus Dial Rear View 1 6 2 7 3 8 4 9 5 1 microSD slot Audio Out (3.
Top View 6 1 7 2 8 9 3 10 11 4 5 1 Menu Button 2 Up Button 5 Power Button 6 Status LED 3 Left Button 7 Exit Button 4 Home Button 8 Enter Button 9 Right Button 10 Down Button Projector/Bluetooth 11 Mode Button LED Color Charge Status RED Charging the device GREEN Fully Charged Bluetooth speaker mode (charge information cannot be BLUE displayed when using this function) Bottom View 1 1 Tripod Connector 10
REMOTE CONTROL Remote Control Keypad 8 1 9 2 10 3 11 4 12 13 5 14 6 15 7 1 Power ON/OFF 2 Menu 3 Up 6 7 8 Volume Down Audio Mode Home 4 Left 9 Mouse* 5 Volume Up 10 Exit 11 Enter 12 Right 13 Down Projector/Bluetooth 14 Mode 15 Mute NOTE: *This feature is not available for the current model of Qumi Z1V 11
Activating the Remote Control Battery When using the remote control for the first time, the plastic sticker covering the battery must be removed. To remove the plastic sticker, pull the tab at the bottom side of the remote control to remove the plastic sticker from the battery compartment. Replacing the Remote Control Battery To replace the remote control battery: 1. Rotate the battery compartment cover counter-clockwise so the line on the cover points to the single dot on the remote control. 2.
POWERING/CHARGING THE PROJECTOR To supply power to the Qumi Z1V: 1. Connect the power cable to a power socket 2. Connect the power cable to the supplied adapter. 3. Connect the adapter cable to the DC In port on the projector. 3 2 1 4. Once the adapter and power cable are connected to the projector, the Status LED on the top of the projector will illuminate indicating the charge status. The charging status will also be indicated on the home screen.
Powering On/Off the Projector To power on the projector: 1. Press the power ( ) button on the top of the projector or the power ( the remote control. ! ) button on IMPORTANT: The remote control can only power on the projector when the projector is connected to a power supply. 2.
To power off the projector: 1. Press the power ( ) button on the top of the projector or the power ( the remote control. ) button on 2. A message will appear on the projected screen to confirm power off. Press the power ( ) button on the top of the projector or the power ( control again.
MAKING CONNECTIONS 2 1 4 3 No.
USING THE PROJECTOR Adjusting the Focus To adjust the focus of the projected image, rotate the dial on the side of the projector until correct focus is achieved.
Playing Video from a Storage Device (USB Flash Drive, microSD Card) To play a video file from a storage device: 1. Connect the device to the projector. Refer to the Making Connections section on page 17. 2. Power on the projector. Refer to the Powering On/Off the Projector section on page 15. NOTE: If you are already viewing video or playing music from a different source press the home ( ) or exit ( ) button on the keypad or remote control to return to the home screen. 3.
NOTE: Only the following video formats are supported: AVI, VOB, MOV, MKV, DAT, MPG, MP4. 6. The video will begin playing on the projected screen. 1 No.
Viewing Photos from a Storage Device (USB Flash Drive, microSD Card) To view an image file from a storage device: 1. Connect the device to the projector. Refer to the Making Connections section on page 17. 2. Power on the projector. Refer to the Powering On/Off the Projector section on page 15. NOTE: If you are already viewing video or playing music from a different source press the home ( ) or exit ( ) button on the keypad or remote control to return to the home screen. 3.
NOTE: Only the following image formats are supported: JPG, JPEG, BMP, PNG. 6. An image slideshow will begin playing on the projected screen starting with the image selected in the previous step. NOTE: The slideshow will cycle through all the images in the folder for 5 seconds per image. 1 No.
Playing Audio from a Storage Device (USB Flash Drive, microSD Card) To play an audio file from Storage Device: 1. Connect the device to the projector. Refer to the Making Connections section on page 17. 2. Power on the projector. Refer to the Powering On/Off the Projector section on page 15. NOTE: If you are already viewing video or playing music from a different source press the home ( ) or exit ( ) button on the keypad or remote control to return to the home screen. 3.
NOTE: Only the following audio formats are supported: MP3, WMA, M4A, AAC. 6. An audio playlist will begin playing on the projected screen starting with the image selected in the previous step. NOTE: The playlist will begin with the image selected in the previous step, and then cycle through all the songs in the folder. 1 No.
Playing from a Video Source (HDMI) To project a video from a device connected to the HDMI port: 1. Connect the device to the projector. Refer to the Making Connections section on page 17. 2. Power on the projector. Refer to the Powering On/Off the Projector section on page 15. NOTE: If you are already viewing video or playing music from a different source press the home ( ) or exit ( ) button on the keypad or remote control to return to the home screen. 3.
USING THE BLUETOOTH SPEAKER You can use Qumi Z1V as a speaker to play music from mobile devices wirelessly via their mobile devices. To use the projector as a speaker: 1. Power on the projector. Refer to the Powering On/Off the Projector section on page 15. 2. Press the Projector/Bluetooth Mode ( ) button on the keypad or the remote control to enable Bluetooth on the projector. 3.
4. Enable Bluetooth on your mobile device and select Qumi Z1V in your mobile device’s Bluetooth pairing menu. NOTE: Once paired your mobile device will automatically connect to the projector. Each subsequent time your mobile device is within range of the projector and Bluetooth is enabled on both devices they will automatically connect to each other. 5. Play music on your mobile device. To deactivate Bluetooth Mode: 1. Press the Projector/Bluetooth Mode ( control. ) button on the keypad or the remote 2.
USING THE SETTINGS MENU The Settings menu allows the user to adjust display, audio, and other settings for the projector. To access the Settings menu: 1. Choose one of the following: Press the menu ( ) button on the remote control or the keypad. Select SETTINGS from the home screen and press the enter ( 28 ) button.
2. The Settings menu will appear on the projected screen. 3.
The Settings Menu DISPLAY SETTINGS Category Menu Item Sub-Menu Item Contrast Brightness Switches the display settings to predefined settings ideal for presentations Switches the display settings to predefined settings that maximize brightness Switches the display settings to predefined settings ideal for movies Adjusts the contrast levels Adjusts the brightness levels Color Adjusts the color values Sharpness Adjusts the sharpness of the image Tint Adds a color tint to the image Color Temperature
AUDIO SETTINGS Category Menu Item Volume Sub-Menu Item -- Description Adjusts the volume of the Qumi Z1V Switches the audio settings to standard predefined settings Switches the audio settings to pre-defined settings ideal for music Switches the audio settings to pre-defined settings ideal for movies Adjusts the frequency levels of the audio settings Standard Audio Settings Sound Mode Music Movie User IMAGE SETTINGS Category Menu Item Aspect Ratio Image Settings Auto Keystone Sub-Menu Item -Man
TIMER Category Menu Item Description Timer Timer Sets a timer that turns off the projector in 10min, 20min, 30min, or 60min.
TROUBLESHOOTING/FAQ These guidelines provide tips to deal with problems you may encounter while using Qumi. If the problem remains unresolved, contact your dealer for assistance. The problem sometimes can be as simple as improper connection of cables. Review the following possible issues before proceeding to the problem-specific solutions. Use another electrical device to confirm that the electrical outlet is properly working. Make sure that Qumi is turned on.
Problem: The image is blurred. 1. Adjust the focus directly via the focus buttons on the projector or remote control 2. Ensure that the distance between the Qumi and the screen is within specified range 3. Clean Qumi lens with optical lens cleaning cloth if it is dirty. Problem: The image is wider at the top or bottom (trapezoid effect). 1. Position Qumi so that it is as perpendicular to the screen as possible. 2.
FAQs 1. Is it possible to connect Qumi to a game console, such as a Microsoft® Xbox or Sony® Playstation? Yes, Qumi can be used to display content from an Xbox or Playstation console. This can be done by connecting the HDMI cable from the game console to Qumi. 2. Can Qumi project content from a television? Watching television content can be done by connecting a cable box, digital set-top box or satellite receiver directly to Qumi.
11. I’ve lost my remote. Where can I get a replacement? Contact your Reseller or Vivitek Service via www.vivitekcorp.com (select region) to obtain a replacement remote (Charges may be applied). 12. Why won’t Qumi recognize my USB flash drive? The USB flash drive must be formatted in FAT32, FAT16 or NTFS. 13.
Timing Mode Table Resolution Horizontal Synchronization Vertical Synchronization [HZ] VESA640x480_60 31.47 59.94 VESA640x480_72 37.86 72.81 VESA640x480_75 37.5 75 VESA800x600_60 37.88 60.32 VESA800x600_72 48.08 72.19 VESA800x600_75 46.88 75 VESA1024x768_60 48.36 60 VESA1024x768_70 56.48 70.07 VESA1024x768_75 60.02 75.03 VESA1280x768_60-RB 47.4 59.99 VESA1280x768_60 47.78 59.87 VESA1280x800_60 49.7 59.81 VESA1280x800_75 62.79 74.93 VESA1280x1024_60 63.98 60.
Specifications - Projector Model No.: Qumi Z1V Native Resolution WVGA (854 x 480) Maximum Resolution 1080p (1920 x 1080) Throw Ratio (Distance/Width) 1.2:1 (Manual Adjustment Focus) Image Size (Diagonal) 0.5m - 1.9m (19.7” - 75”) Projection Distance 0.5m - 2.0m (1.6ft - 6.6ft) Aspect Ratio 16:9 Native Keystone Correction Vertical ±30°(Auto Keystone) Bluetooth® Audio Yes (Bluetooth® 4.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Vivitek Americas 46101 Fremont Blvd, Fremont, CA 94538 U.S.A. T: +1-510-668-5100 F: +1-510-668-0680 Vivitek Asia 7F, No. 186, Ruey Kuang Road, Neihu, Taipei 11491 Taiwan R.O.C. T: +886-2-8797-2088 F: +886-2-6600-2358 Vivitek Europe Zandsteen 15, 2132 MZ Hoofddorp The Netherlands T: +31-20-800-3960 F: +31-20-655-0999 www.vivitekcorp.