ViviCam XX14 Digital Camera User Manual © 2009-2016 Sakar International, Inc. All rights reserved. Windows and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks are the property of their respective companies.
TABLE OF CONTENTS Introduction .................................................................................................................................. 2 Getting to Know Your Camera ...................................................................................................... 2 What’s Included ............................................................................................................................ 3 Parts of the Camera ....................................................
Introduction Thank you for purchasing this camera. Everything you need to take quality digital photos and videos is included with your camera. Vivitar makes capturing those special moments as easy as possible. Please read this manual carefully first in order to get the most out of your digital camera. NOTE: Your camera requires a Micro SD Memory card (up to 32GB) for normal use. Micro SD Memory cards are not included and need to be purchased separately. This camera is a Plug and Play device.
What’s Included 1. Digital Camera 2. USB cable 3. Vivitar Experience Image Manager Software Installation CD 4. Wrist Strap Note: SD Memory Card and batteries not included.
Parts of the Camera 1. Power Button 12. ViviLink / Down Button 2. Shutter Button 13. Microphone 3. LCD Screen 14. Flash Light 4. LED 15. USB Slot 5. Zoom Out 16. Tripod Socket 6. Zoom In 17. Digital Lens 7. MODE button 18. Battery Compartment 8. SET button 19. SD Memory Card Slot 9. Scene / Left Button 20. MACRO Switch 10. Flash / Up / Slide Show 21. Wrist Strap Connector 11. Delete / Right Button 22. Speaker (Buzzer) 23.
Initial Camera Setup INSTALLING THE BATTERIES INSTALLING THE MEMORY CARD Insert 3 AAA (1.5V) batteries. Alkaline batteries recommended (not included). SD Memory card (up to 32GB) needed for normal use.
POWERING THE CAMERA ON 1) Batteries Make sure the batteries have been inserted properly into your digital camera, according to the polarity shown inside the battery compartment. Use 3x AAA (1.5v) batteries. Alkaline batteries are recommended. Batteries not included. Note: Remove the batteries from the camera when not in use for an extended period. Do not mix alkaline and non-alkaline batteries. Some features, such as Flash, will not work if the battery power level is low.
Note: After the camera is powered on, an SD icon will appear on the LCD display. If you do not see the SD icon on the display, please check if the card was inserted properly. Make sure the SD card is not locked (check the lock switch on the side of the SD card). If the SD card is locked this will prevent the camera from saving captured photos to the SD card. 3) Power On Press the POWER button to turn on the camera.
Setting the Date and Time The next step in the initial camera setup is to set the date and time on the camera. 1) Press the UP/DOWN button to change and set the specific time/date settings. 2) Press the RIGHT/LEFT button to move/toggle to a different part of the time/date setting options. 3) Once you have set the date and time as desired press the SET button to confirm the setting and move to the next part of the camera setup.
Main Camera Modes Your camera has different modes for the various camera functions. You can switch modes by pressing the MODE button on your camera after the camera has been powered ON. PHOTO CAPTURE MODE Use this mode to capture pictures with your camera. This is the default mode when the camera is powered ON. To take a picture, aim your camera as desired and press the Shutter button. The picture will be automatically saved to your camera’s memory card.
Camera Technical Specifications Image Sensor Image Resolution CMOS Sensor 20MP (5200X3900), 18MP (4896X3672), 16MP (4608X3456), 14MP (4416X3312), 12MP (4000X3000), 10MP (3648X2736), 8MP (3264X2448), 7MHD (3648X2048), 5MP (2592X1944), 3M (2048X1536), 2MHD (1920X1080), VGA (640X480) Video Resolution HD (1280X720), VGA (640X480), QVGA (320X240) File Format JPEG (Photo) /AVI (Video) Internal Memory 1 Test Photo Use Only (3M) External Memory SD Memory Card (up to 32GB) LCD Display 1.
Computer System Requirements To be able to download photos and videos to your computer using the Vivitar Experience™ Image Manager Software, you will need the following minimum configuration: WINDOWS OS MICROSOFT® Windows XP with Service Pack 3, Windows Vista with Service Pack 1 or MICROSOFT® Windows 7 or above Pentium® 4 processor (or above) 1 GB RAM, 250 MB available hard disk space 16-bit Color monitor, 1024 X 768 recommended screen resolution CD-ROM Drive QuickTime® 6 or higher
Powering the Camera On/Off Make sure the batteries have been inserted properly into your digital camera. If your camera comes with a rechargeable lithium battery, make sure it is fully charged before the first use. Make sure an SD card has been inserted into your camera. (SD card up to 32GB - SD Card not included) Please see Initial Camera Setup for more information. POWERING THE CAMERA ON Press the Power button to turn your camera ON.
Changing Camera Mode Your camera has three main modes: 1) Photo Capture Mode - Use this mode to capture photos with your camera. 2) Video Capture Mode - Use this mode to capture videos with your camera. 3) Playback Mode (for photos and videos) - Use this mode to view the photos and videos you have already taken with your camera. When the camera is first powered ON, the Photo Capture Mode is automatically active.
Navigating the Menus Each camera mode has a set of menus specific to that mode. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll between the various menus for the current mode. 3) Press the UP or DOWN button to highlight the desired menu selection. 4) Press the SET button to confirm and save the highlighted menu option. 5) If the selection can be remembered by the camera, a selection icon appears to the right of the selected menu option.
Camera Features: ViviLink, Macro, Flash, Display VIVILINK OPTION The ViviLink technology allows you to quickly and easily upload your camera’s photos and videos to the social networks of your choice with the accompanying Vivitar Experience™ Image Manager application. A ViviLink destination can be assigned to a photo or video in Capture mode prior to capturing your image or in Playback Mode. ViviLink: Video or Photo Capture Mode Press the DOWN Quick Function Button to open the ViviLink options.
FLASH OPTIONS There are several Flash options available on your camera. The options appear in sequence on the LCD screen in the Photo Capture Mode. To change the Flash mode, press the UP Quick Function button until you arrive at your desired settings. Important: Please make sure the MACRO mode is turned OFF when you want to use the Flash. When the camera is in MACRO mode (ON), the camera will not fire a flash, as MACRO mode is suitable for close-up photography.
MACRO SWITCH / MACRO ON: Your camera contains a MACRO Switch that allows you to manually enable or disable the MACRO mode on your camera. While using the MACRO mode, you can capture images at close range (30~45cm). To turn the MACRO mode ON, slide the Macro Switch located on the side of your camera UP to the flower icon . When enabled, the MACRO mode allows your camera to focus on an object that is close to the camera. The flower icon appears on the LCD and indicates that the Macro mode is ON.
Note: The MACRO mode must be turned OFF when you want to use the following feature of your camera: Flash. To Turn the MACRO mode OFF: Slide the MACRO Switch down to the mountain icon to turn Macro mode OFF. The mountain icon will appear on the LCD display. HIDE/SHOW THE LCD ICONS The display of the icons on the LCD screen can be hidden or visible as desired. 1) Hold the MODE button for 2 seconds to hide the display of the icons on the screen.
Photo Capture Mode The Photo Capture mode allows you to capture pictures with your digital camera. TAKING A PICTURE 1) Selecting the Scene with the LCD Display: While in Photo Capture mode, use the LCD display on the back of the camera to direct the camera at the scene you would like to capture. Note: Make sure the MACRO mode is set to your desired mode: Standard photo capture using MACRO OFF 2) , or close up photo capture using MACRO ON .
SELFIE / SELF PORTRAIT PHOTO CAPTURE You can also include yourself in your photos by using the Selfie / Self Portrait capability. 1) Push the Macro switch lever up (Macro On) for the flower icon to appear. 2) Make sure the LCD screen is rotated out 180°. 3) Hold the camera steady out facing towards you at arm’s length (about 10~30cm). The LCD screen should be out facing towards you so that you can see yourself on the LCD screen. 4) Look at the camera lens.
PHOTO CAPTURE MODE QUICK FUNCTION BUTTONS Your digital camera has a four-directional pad that functions as Quick Function buttons: Quick Function Function Button LEFT UP SCENE SELECTION – Opens the ‘Scene’ menu. FLASH OPTIONS – Toggles between the following Flash options: Forced Off, RIGHT Forced On, A Auto Flash, Red Eye Reduction DELETE – Opens the ‘Delete This Photo’ option and allows you to view and delete the last photo taken. DOWN VIVILINK – Opens the ‘ViviLink for Photos’ menu.
PHOTO CAPTURE MODE MENUS The following are the menus that appear in your camera’s Photo Capture Mode. The selection icon appears by the default settings. Once you change a setting, the setting is saved by your camera until you manually change the setting or restore the camera’s default factory settings.
Scene Menu The ‘Scene’ menu allows you to choose scene settings that let your camera to adapt properly to your current environment. Note: When selecting the HIGH SENSITIVITY Option, by default the camera switches off the FLASH automatically (if it’s ON) to optimize the picture quality. If however, you would like to override it and manually turn ON the flash – you can do so. Remember: The ‘Scene’ menu is also accessible by pressing the LEFT Quick Function Button while in Capture Mode.
5) To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item. 6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. An icon reflecting your selection is displayed on the LCD screen. Image Quality Menu The ‘Image Quality’ menu allows you to select the desired quality level of the images taken by your camera.
2) Press the LEFT or RIGHT button to scroll and select the ‘Self Timer’ menu. 3) Press the UP or DOWN button to highlight a specific option. 4) Press the SET button to confirm and select the highlighted menu option. A 5) selected option icon appears on the selected item. To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item. 6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode.
other scenes with quick movements. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Multi SnapShots’ menu. 3) Press the UP or DOWN button to highlight a specific option. 4) Press the SET button to confirm and select the highlighted menu option. A 5) selected option icon appears on the selected item. To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item.
Color Effect Menu The ‘Color Effect’ menu allows you to choose a color effect to add to the images taken with your camera. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Color Effect’ menu. 3) Press the UP or DOWN button to highlight a specific option. 4) Press the SET button to confirm and select the highlighted menu option. A 5) selected option icon appears on the selected item.
Light Exposure Menu The ‘Light Exposure’ setting helps you control the amount of light that enters your camera’s lens. This setting should be adjusted when the environment is lighter or darker than normal. When the environment has more light than is needed, reduce the exposure setting (by using the negative - count) to reduce the amount of light allowed into the lens by your camera.
5) To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item. 6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. An icon reflecting your selection is displayed on the LCD screen. Metering Menu The ‘Metering’ setting will affect how your camera focuses when capturing an image.
Language Menu You can select your camera’s language setting by selecting the desired language from the ‘Language’ menu. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Language’ menu. 3) Press the UP or DOWN button to highlight a specific option. 4) Press the SET button to confirm and select the highlighted menu option. A 5) selected option icon appears on the selected item.
6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. To Set the Date and Time: 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Date/Time’ menu. 3) Press the UP or DOWN button to highlight the ‘Date Setup’ menu option, then press the SET button to select the option. 4) The ‘Date Setup’ submenu will open. 5) Scroll through the window with the RIGHT and LEFT buttons.
Auto Power Off Menu You can use the ‘Auto Power Off’ feature in order to conserve you camera’s battery life. The designated time represents when your camera will automatically power off. When the camera sits idle for the designated period of time, the camera will shut off completely and will need to be powered on again with the power button before the next use. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Auto Power Off’ menu.
Format Memory Card Menu You can use the ‘Format Memory Card’ menu to delete all of the content that is currently on your camera’s memory card. Keep in mind that formatting the memory card will permanently delete all of the content on your camera’s memory card. This option will delete all of the content at one time. If you would like to delete individual images, use the delete menu in the camera’s Playback mode. Note: Restoring factory defaults or formatting the camera may result in the loss of data.
• Select ‘No’ to exit the menu and return to the previous mode without resetting to the default settings. • Select ‘Yes’ and press the SET button to proceed with the reset. You will then automatically exit the menu and return to the previous mode with the digital camera settings set to the Factory Default Settings. Note: After RESETTING to the default settings, it is recommended to select your system Language, Date/Time and ViviLink for Photos and Videos.
Photo Playback Mode The Playback Mode allows you to review and edit photos and videos that you’ve already taken with your camera. When you first turn on the camera, the camera will be in Photo Capture mode by default. Press the MODE button twice to open the Playback Mode. The latest captured image appears on the LCD screen. If there are no images stored, a message (No File) appears.
THUMBNAIL VIEW Easily navigate and select the image you wish to view by using the Thumbnail View. The images on your camera will be displayed in a 3 X 3 matrix where you can use the direction buttons to scroll and select images from the thumbnails. To access the Thumbnail View: 1) Press the W / Zoom Out / button. All the images on your camera appear in the Thumbnail View. 2) Use the UP / DOWN / LEFT / RIGHT direction buttons to scroll and select the image you wish to view.
MODE Video Capture Mode and Playback Mode. Exits the menu screen. ZOOM - Zooms In to selected photo. T / MODE SELECTION - Toggles between the Photo Capture Mode, W ZOOM - Zooms Out of selected photo. THUMBNAIL - Opens Thumbnail View. To navigate in the Thumbnail View press the UP/DOWN/LEFT/RIGHT direction buttons. To select an image in the Thumbnail View press the SET button.
Delete Menu While in the Playback Mode, you can delete pictures from your camera through the ‘Delete’ menu. 1) Select the photo you would like to delete. 2) Press the SET button to open the menus for the current mode. 3) Press the LEFT or RIGHT button to scroll and select the ‘Delete’ menu. 4) Press the UP or DOWN button to highlight a specific option. To delete the selected photo: Select “Delete This Photo?” and press the SET button. You will be asked to confirm the deletion of the photo.
ViviLink for Photos Menu The ViviLink technology allows you to quickly and easily upload your camera’s photos and videos to the social networks of your choice with the accompanying Vivitar Experience™ Image Manager application. 1) Select the photo you to which you would like to add a ViviLink. 2) Press the SET button to open the menus for the current mode. 3) Press the LEFT or RIGHT button to scroll and select the ‘ViviLink’ menu. 4) Press the UP or DOWN button to highlight a specific option.
Crop Image Menu You can crop pictures on your camera with the Crop feature. Note: VGA resolution photos cannot be cropped. 1) View the photo you would like to crop. 2) Press the SET button to open the menus for the current mode. 3) Press the LEFT or RIGHT button to scroll and select the ‘Crop’ menu. 4) Press the UP or DOWN button to highlight the ‘Crop’ option. 5) Press the SET button to select and open the Crop option. 6) The Crop window opens on the selected picture.
Photo’ and then press the SET button. The image now appears in Playback Mode without the lock icon. To Lock All Images: To lock all captured videos and photos use the UP or DOWN button to highlight ‘Lock All Images’ and then press the SET button. All images now appear in Playback Mode with the lock icon . To Unlock All Images: To unlock all locked videos and photos use the UP or DOWN button to highlight ‘Unlock All Images’ and then press the SET button.
Slide Show Menu You can view a Slide Show of all the pictures taken with your camera by pressing the UP Quick Function button while in Playback mode. The ‘Slide Show’ menu allows you to set the interval length of time that each picture will display during the slide show. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Slide Show’ menu. 3) Press the UP or DOWN button to highlight a specific option.
Video Capture Mode The Video Capture Mode allows you to capture videos with your digital camera. When the camera is first powered ON, the camera will be in Photo Capture Mode. Press the MODE button once to access the Video Capture Mode. TAKING A VIDEO 1) Selecting the Scene with the LCD Display: While in Video Capture mode, use the LCD display on the back of the camera to direct the camera at the scene you would like to capture.
VIDEO CAPTURE MODE QUICK FUNCTION BUTTONS Your digital camera has a four-directional pad that functions as Quick Function buttons. Quick Function Button Function LEFT SCENE SELECTION – Opens the ‘Scene’ menu. UP LIGHT EXPOSURE – Opens the ‘Light Exposure’ menu. RIGHT DELETE – Opens the ‘Delete This Video’ option and allows you to view and delete the last video taken. DOWN VIVILINK – Opens the ‘ViviLink for Videos’ menu. Other Shutter SET START/STOP – Starts and stops the video capture.
VIDEO CAPTURE MODE MENUS The following are the menus that appear in your camera’s Video Capture Mode: The Once you change a setting, the setting is saved by your camera until you manually change the selection icon appears by the default settings. setting or restore the camera’s default factory settings.
Scene Menu The ‘Scene’ menu allows you to choose scene settings that let your camera to adapt properly to your current environment. Note: Remember: The ‘Scene’ menu is also accessible by pressing the LEFT Quick Function Button while in Capture Mode. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Scene’ menu. 3) Press the UP or DOWN button to highlight a specific option.
6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. An icon reflecting your selection is displayed on the LCD screen. Image Quality Menu The ‘Image Quality’ menu allows you to select the desired quality level of the images taken by your camera. Keep in mind that images with a higher image quality level will also take up more memory on your camera. 1) Press the SET button to open the menus for the current mode.
A 5) selected option icon appears on the selected item. To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item. 6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. An icon reflecting your selection is displayed on the LCD screen. Color Effect Menu The ‘Color Effect’ menu allows you to choose a color effect to add to the images taken with your camera.
A 5) selected option icon appears on the selected item. To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item. 6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. An icon reflecting your selection is displayed on the LCD screen. Light Exposure Menu The ‘Light Exposure’ setting helps you control the amount of light that enters your camera’s lens.
sensitivity to light however, may reduce the quality of the images that are taken. When the ISO is reduced, the image sensor in your camera will be less sensitive to light and will optimize the image quality in environments with bright lighting. 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘ISO’ menu. 3) Press the UP or DOWN button to highlight a specific option.
A 5) selected option icon appears on the selected item. To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item. 6) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. An icon reflecting your selection is displayed on the LCD screen. Language Menu You can select your camera’s language setting by selecting the desired language from the ‘Language’ menu.
To Enable/Disable the Timestamp: 1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Date/Time’ menu. 3) Press the UP or DOWN button to highlight a specific option. 4) Press the SET button to confirm and select the highlighted menu option. A 5) selected option icon appears on the selected item. To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item.
1) Press the SET button to open the menus for the current mode. 2) Press the LEFT or RIGHT button to scroll and select the ‘Auto Power Off’ menu. 3) Press the UP or DOWN button to highlight a specific option. 4) Press the SET button to confirm and select the highlighted menu option. A 5) selected option icon appears on the selected item. To continue within the menus and select a different menu option: Press the LEFT or RIGHT button to select the next menu item.
Format Memory Card Menu You can use the ‘Format Memory Card’ menu to delete all of the content that is currently on your camera’s memory card. Keep in mind that formatting the memory card will permanently delete all of the content on your camera’s memory card. This option will delete all of the content at one time. If you would like to delete individual images, use the delete menu in the camera’s Playback mode. Note: Restoring factory defaults or formatting the camera may result in the loss of data.
• Select ‘No’ to exit the menu and return to the previous mode without resetting to the default settings. • Select ‘Yes’ and press the SET button to proceed with the reset. You will then automatically exit the menu and return to the previous mode with the digital camera settings set to the Factory Default Settings. Note: After RESETTING to the default settings, it is recommended to select your system Language, Date/Time and ViviLink for Photos and Videos.
Video Playback Mode The Playback Mode allows you to review and edit photos and videos that you’ve already taken with your camera. When you first turn on the camera, the camera will be in Photo Capture mode by default. Press the MODE button twice to open the Playback Mode. The latest captured image appears on the LCD screen. If there are no images stored, a message (No File) appears.
THUMBNAIL VIEW Easily navigate and select the image you wish to view by using the Thumbnail View. The images on your camera will be displayed in a 3 X 3 matrix where you can use the direction buttons to scroll and select images from the thumbnails. To access the Thumbnail View: 1) Press the W / Zoom Out / button. All the images on your camera appear in the Thumbnail View. 2) Use the UP / DOWN / LEFT / RIGHT direction buttons to scroll and select the image you wish to view.
To navigate through the Menus, press the UP/DOWN/LEFT/RIGHT direction control buttons. MODE Toggles between the Photo Capture Mode, Video Capture Mode and Playback Mode. Exits the menu screen. THUMBNAIL VIEW – Opens the Thumbnail View. / W To navigate in the Thumbnail View press the UP / DOWN / LEFT / RIGHT direction buttons. To select an image in the Thumbnail View press the SET button.
If you would like to proceed with deleting the current image, select ‘Yes’ and press the SET button to confirm. The video will be deleted and you will exit the menu and return to the Playback mode. If you do not want to delete the current image, select ‘No’ and press the SET button. The video will not be deleted and you will exit the menu and return to the Playback mode.
7) To exit the menu view: Press the MODE button to exit the menu and return to your previous mode. Note: An icon appears on the image with the selected ViviLink destination site when you return to the Playback display. Remember that the ViviLink feature is deactivated by default. A ViviLink destination will only be assigned to a photo or video if you manually set it from this menu or from the ViviLink menu in Capture mode (accessible with the ViviLink Quick-Function button in Capture mode).
To unlock all locked videos and photos use the UP or DOWN button to highlight ‘Unlock All Images’ and then press the SET button. The images now appear in Playback Mode without the lock icon. 5) Press the MODE button at any time to exit the menu and return to your previous mode. Note: Any image that is locked displays a lock symbol on the LCD screen when viewing that image in the Playback Mode. Videos that are not locked do not display the lock symbol.
Installing the Software The Vivitar Experience Image Manager Software can be installed either using the included CD ROM or by accessing the link online. INSTALLING THE SOFTWARE – USING THE CD ROM You must be connected to the Internet to install and run the Vivitar Experience Image Manager Software. 1) Insert the installation CD into your CD-ROM drive. The installation screen should automatically open. 2) On WINDOWS OS: The Vivitar Experience Image Manager Installer window appears.
NOTE: If you do not have Internet access, you can still download media from the camcorder. Click the “How to transfer photos and videos from my camera to my computer” button for instructions. 5) If you have Internet access, the “Choose your language” window opens, choose your language and click “Next” to open the next window. 6) Select your camera model from the list and click “Next” to open the next window. 7) Click “Next” to confirm your camera model selection and to install the application.
INSTALLING THE SOFTWARE – USING THE ONLINE LINK The Vivitar Experience Image Manager Software can also be downloaded and installed via the following online links: WINDOWS OS: http://tinyurl.com/viviwin MAC OS: http://tinyurl.com/vivimac 1) Enter the appropriate URL (shown above) into a web browser on your computer. 2) The file for installing the software automatically begins to download to your computer. Please note that the web page may appear empty, however the download automatically begins.
Getting Videos and Photos from the Camcorder to the Computer The Micro SD Memory card needs to be inserted. Do not disconnect the cable during transfer. Doing so will cancel the transfer of any files on their way to your computer. 1. Select the “Get Images” button from the Main menu. 2. The “Get media from device” window opens. 3. You can select to download photos, videos or both. 4. Select your camera (removable disk) from the device window.
Getting Started! Using the Vivitar Experience Image Manager you can: Upload and manage videos to and from the most popular photo sharing and social networking sites - Facebook, Flickr, Picasa, MySpace, Photobucket, Twitter, and YouTube Seamlessly transfer photos and videos from one social network to another Organize your images by creating offline and online albums Edit images using automatic and manual tools Use automatic “Geotagging” with built in Google Maps For more details on how to
TRANSFERRING PHOTOS AND VIDEOS: MACINTOSH OS 1) Use the supplied USB cable to connect your camera to your computer. 2) ‘MSDC’ appears on the LCD. 3) The camera’s device icon appears on the desktop. 4) Click on the device icon and open the DCIM folder and the folder inside to view the media files. 5) Select the files and drag them into your computer. Optionally, select the files and choose Copy from the Finder’s Edit menu. Then select a folder and choose Paste from the Edit menu.
Camera Maintenance The digital camera is a delicate device. Please handle your camera with care to avoid damaging it. Do not expose your camera to heat sources. Do not use you camera in wet or moist conditions. Sakar Warranty Card This warranty covers for the original consumer purchaser only and is not transferable.
Technical Support For technical support issues please visit our website at www.vivitar.com . You can find manuals, software and FAQ’s at the website. Can’t find what you are looking for? E-mail us at support@vivitar.com and one of our technical support team members will answer your questions. For phone support in the US please call 1-800-592-9541, in the UK call 0800 917 4831, in Australia call 1800-006-614. If you would like to call from anywhere else, please visit www.vivitar.