LF STA RD MOTION SERIES | contents CONTENTS R «intro letter included in box SIA 4 general info wall & ceiling mount ceiling hang & OPERA] 4 types of control manual control automatic trigger control external control IR remote control remote controller motorized screen usage « warnings important information specifications — NINTH
STANDARD MOTION SERIES | introduction INTRODUCTION Dear Customer! Congratulations on making your purchase. We hope you enjoy using your new projection screen. In order fo make each viewing a unique video-cinema experience, we have provided this user manual containing detailed information about installing and operating your new projection screen. Bo sure fo read through all the information in this manual before using and/or attempting fo install the equipment.
STANDARD MOTION SERIES | installation INSTALLATION General Information There are 3 ways to install you Vivid screen. © Wall Mount « Ailing Mount * Ailing Hang Select the types of installation that is best for you. NOTE: The floating mounting brackets can be installed at various points for your convenience. However, it is recommended that you install them closer to the deadpan to reduce vibration and noise. Wall & Ceiling Mount Figure 1 1.
STANDARD MOTION SERIES | installation Figure 2 Figure 3 Wood Wall Wood Calling 3. Simply use the screws as shown figure 2 & 3 for wood wall and ceiling installations. Use the provided anchors as shown in figures 4&5 for drywall and concrete wall and ceiling applications. 4. Loosen the locking screw fo lower the locking piece as shown in figure 6 &7 to prepare the floating mounting brackets before attaching the screen. Figure 4 Figure 5 Drywall & Concrete Wall Drywall & Concrete Ailing 5.
STANDARD MOTION SERIES | installation Ailing Hang Figure 10 Figure 11 Install Hawks For Hanging Secure Hang Brackets 1. Install 2 hooks {not provided) on the ceiling as Shawn in figure Use the installation screws fo 1 4 secure the hang brackets into the mounting brackets as shown in figure 11. 3. Loosen the locking screw to lower Figure 12 Figure 13 the locking piece as shown in figure Loosen Locking Screw Lower Locking Piece 12&13 4.
ARD MOTION SERIES | control & operation CONTROL & OPERATION 4 Types of Control 1. Manual Control 2. Automatic Trigger Control 3. External Control 4.
STANDARD MOTION SERIES | control & operation Manual Control Usa the manual control switch to operate the standard motion screen. {See figure 18) Simply lick the bunion next to the power cord lo make your screen go down. Click again fo slop. Click once again lo make the screen go up. Click again fo stop.
STANDARD MOTION SERIES | control & operation Automatic Trigger Control Control your screen using the automatic 12v trigger with your projector. Use the 12v trigger line to connect the 12v output to the rigger jack, labeled TRIG on the end cap of your screen. (Sas figure 19} Wuhan the projector is powered on, your screen will automatically go down, When the projector is powered off, your screen will automatically go up. A wireless option is available.
STANDARD MOTION SERIES | control & operation External Control Use an external device such as a computer for centralized control of your standard motion screen. Connect ane end of your data cable fo the screens output jack and the other end to your control device. [Ses figure 20] Use your control device fo put the screen up and down.
STANDARD MOTION SERIES | control & operation IR Remote Control Control your motion series screen with the provided IR remote. The screen has a builtin IR sensor that will work if the remote’s IR signal is not blocked. {Ses figure 21) If your installation environment leaves the builtin IR sensor blocked, simply uss the external IR receiver that is provided. {Ses figure 21} Be sure the external IR receiver is positioned so that the IR signal being sent from the remote can reach it without interference.
STANDARD MOTION SERIES | control & operation Remote Controller 1. To raise screen press UP. 2. To hold scrawny at desired position pass STOP. 3. To lower screen press DOWN. 4. To raids the screen lite at your desired position press MICRO-UP. 5. To lower the screen little at your desired position press MICRO-DOWN. Figure 22 Remote Operation & Battery Replacement LED BATTERY COMPARTMENT up STOP DOWN MICRO DOWN MICRO.UP Caution: 1. The shortest distance between re rar and controller is 0.5 meter. 2.
STANDARD MOTION SERIES | maintenance & safety MAINTENANCE & SAFETY Motorized Screen Usage 1. Make sure there is no dust or dirt on the fabric surface before putting ths screen up. 2. Motor operation should not exceed 50 seconds of continuous use. 3. The motor will utilize overheat protection in excessive usage situations. User will be forced to wait for the motor to cool down before operation will resumes. 4. The motor does not require lbs for optimum operation. 5. Motor settings have been optimized.
MOTION SERIES | maintenance & safety Warnings * * The warranty will only be valid if you follow the instructions below. Improper use and care may cause serious injury and/er damages. Make sure the installation and mounting screws are securely fastened. Make sure the mounting surface is flat and secure. Please consult a professional to install your motorized screen. If using IR, ensure that your IR receiver is not pointed directly at a light.
STANDARD MOTION SERIES | maintenance & safety Important Information Read and understand all Instructions before Installing and using the projection screen. Always connect this projection screen toa grounded outlet located near the screen and easily accessible. This equipment must be supplied from a power system providing a PROTECTIVE EARTH connection and having a neutral connection, which can be reliably Identified. Always ensure that the unit Is properly earthed and power connections correctly made.