CNM A SARI INTRODUCTION oo] MAINTENANCE Ps copyright + maintaining & cleaning included in box troubleshooting safety rules specification data environmental condition wiring instruction attention for installation installation options installation of control box « testing operation fine adjustment NL
PRODUCTION Dear Customer Congratulations on making your purchase. We hope you enjoy using your new projection screen. In order to make each viewing a unique video-cinema experience, we have provided this user manual containing detailed information about installing and operating your new projection screen. Be sure to read through all the information in this manual before using and/or attempting to install the equipment.
TAB TENSION SERIES | introduction Internal Structure of Important Parts 01. Screen Housing 02. Tubular Motor 03. Up Limit Switch 04. Down Limit Switch 05. End Cap 06. Control Box 07.
PRECAUTIONS TENSION SERIES Safety Rules 1) The environment must be dry where the screen is used. 2) The control box and motor must be maintained by professionals. Otherwise it might cause severe accident if you open and remove the housing. 3] Never clean the housing and remote controller with watery towel or wash them directly with water. It may cause severe accident, or even casualty. 4) Do not stand near the screen, when extending or retracting. 5) Do not attach any objects on the screen.
TAB TENSION SE ES | precautions Attention For Installation 1) The screen should be mounted indoors. 2) Please make sure that the selected installation structures are sturdy enough and suitable for the screen. 3) Keep the screen housing horizontal {using horizontal level) 4) Dangerous for children, the installation should be performed by adults only.
TENSION SERIES installation INSTALLATION Installation Options You have three options fo choose for installing your motorized screen, based on your specific environment. Please read the instruction below carefully before starting fo install. Option 1: Wall Mounting Use a horizontal level to check whether the screen is Use a gape to measure the level or not. (figure 5) distance between the two holders on the housing {figure 1.
TAB TENSION SE Option 2: Ceiling, Mounting 9 Use a tape to measure the distance between the two holders on the housing {figure 1.) According to the measurement, drill two identical holes on the ceiling and ensure they are level {figure 2&3). Drive the screws directly into the keyholes to fix the screen on the ceiling (figure 4} Use a horizontal level fo check whether the screen is level or not.
TENSION SERIES installation Installation of Control Box You can now mount the control box on the wall with the mounting set included in the accessories. Please proceed as follows: a. Use metal bracket and mark two points on the wall. b. Drill two identical holes in the wall. c. Insert a © 6X30 plastic anchor inch each hole, then screw the 4X20 self tapping screw through the metal bracket in order to fix it. d. Slip the control box inch the bracket from up to down.
TAB LARIAT d. Install the 12V battery in the compartment on the back of the remote control. Check whether the cremate control is functioning by pressing the up, stop and down buttons in sequence and watch the action of screen canvas. The effective distance of the remote control is 8-10M. Fine Adjustment The upper margin has been set before delivery. If you need to alter the adjustment of “Up Limit Switch” and “Down Limit Switch”, proceed as follows: a.
TENSION SERIES | maintenance MAINTENANCE MAINTAINING AND CLEANING The screen housing can be cleaned when the screen is unplugged. Do not use watery towel or wash it with water directly. The screen canvas should be cleaned by dry towel. Do not touch screen surface directly fo avoid damage, scratch and pollution. Never hang anything on the screen housing to prevent overburden. Cut off electricity and retract the canvas when not in use.
TAB LARIAT nce TROUBLESHOOTING Screen does not operate: Remote control doesn’t work, Noise control box works correctly: ‘Wong and {) pole for batter Prong {4 + {pole Change the direction if it is wrong Foreign objects attached on housing, roller or fabrics Incorrect power supply Remove the foreign objects Check the type of power supply and see whether it is Noise in miter gear correctly connected Programming in the control Replace with a new motor Thermal Overload Stop the system for 15 minutes and iry agai
FEATURES Specification Data Power Supply: 120V~60Hz Output: 14W Operating Temperature: 10-40°C Maximum Remote Control Range: 8-10M