Quick Start Guide

ManualsBrandsVitek ManualsCamera & Photo8 MP Indoor/Outdoor IR Dome Camera 3.3-12mm Lens

VITEK

FEATURES

• 1/2.5” 8.0 Megapixel Progressive Scan CMOS image

sensor

• Up to 30fps live view @ 8 MegaPixel (3840x2160)

• Motorized 3.3-12mm Varifocal Lens

• 30 Infrared LED’s with 100’ IR Range

• 120dB Super Wide Dynamic Range (WDR)

• True Mechanical Day/Night function by ICR

• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction

• Fully Programmable Intelligent Analytics including Object

Removal/Museum Search, Line Crossing, and Area

Intrusion Detection

• H.265/H.264/MJPEG Triple Streaming

• Secondary Video Output (CVBS)

• Remote Viewing via CMS, Internet Explorer, and iOS &

Android Apps

• IP66 Weather Resistance & IK10 Impact Rating

• MicroSD memory card slot for Local recording supporting

up to 128GB MicroSDXC cards

• ONVIF Compliant

• Optional Wall (VT-TWM03) & Junction Box (VT-TJB02)

Mounts Available

• 12VDC & PoE (Power over Ethernet) Operation

VTD-TND8RMS

Transcendent Series 8

Megapixel H.265 Indoor/

Outdoor WDR IP Dome Camera

with 30 IR LED Illumination &

Motorized Varifocal Lens

QUICK START GUIDE

PLEASE NOTE:

Complete User Guide, Software, Tools, and Updates are

available online. Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

Summary of content (8 pages)

PAGE 1
VTD-TND8RMS Transcendent Series 8 Megapixel H.265 Indoor/ Outdoor WDR IP Dome Camera with 30 IR LED Illumination & Motorized Varifocal Lens QUICK START GUIDE VITEK VITEK FEATURES • 1/2.5” 8.0 Megapixel Progressive Scan CMOS image sensor • Up to 30fps live view @ 8 MegaPixel (3840x2160) • Motorized 3.
PAGE 2
Components and Accessories Camera Drill Template Quick Guide Rubber Gasket Screws Waterproof Cap Hex Wrench Service Port Cable 1 Overview 2 3 4 5 6 7 8 9 RE SET TF 10 LIN K DC CV IN BS 1 RJ-45 Ethernet 6 RS-485 2 Audio In 7 Power Cable 3 Audio Out 8 Reset 4 CVBS Output 9 Service Port 5 Alarm I/O 10 MicroSD Card Slot 2
PAGE 3
Network Cable & Power Connections Ne tw o rk Ca ble First connect the Waterproof Cap to an Ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power Cable to an approved 12VDC Power Supply. RS-485 + RS-485 - ALM: COM ALM: NO ALM: IN ALM: GND Optional 12VDC Power Connection. Not needed with PoE Weather Resistant Network Coupler 1. Loosen the nut from the Weather Resistant Network Coupler, 2.
PAGE 4
Installation Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows: 1. Loosen the screws to open the lower dome and then loosen the lock screw to remove the mounting base. Lock Screw 2. Attach the drill template to the place where you want to install the camera, then drill 4 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template.
PAGE 5
Installation 4. Install the camera to the mounting base with the lock screw. 5. Adjust the Three-axis camer bracket to obtain the optimium viewing angle. Pan 0°~360° Tilt 0°~75° 6. Install the dome bubble on the camera with the screws, then carefully remove the protective film to complete the installation.
PAGE 6
LAN Configuration The camera can be accessed on the local network either using the IP-Tool or directly in a web browser. 1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template Accessing the Camera Using the IP-Tool 1. Make sure the camera and PC are connected to the LAN. 2.
PAGE 7
4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM . IE browser will download the Active X control automatically. After downloading, a login window will pop up as shown below: Input the user name and password to log in. Default user name: admin / Default password: 123456. Directly Access Through a Web Browser The default network settings are as shown below: IP address: 192.168.226.201 HTTP: 80 Subnet Mask: 255.255.255.0 Data Port: 9008 Gateway: 192.168.226.
PAGE 8
2. Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control automatically. Rubber Plug 3. After downloading Active X control, the login dialog box will pop up. 4. Input the default username and password and then enter to view. WAN Configuration Access the camera by the router or virtual server for example. 1.