MIGHTY DOME TRIO 2.1 Megapixel EX/HD-SDI/TVI/960H All-in-One Dome Camera Series VITEK • Sony 1/2.8” 2 MegaPixel “STARVIS” CMOS Image Sensor • Up to 2.1 Megapixel with EX/HD-SDI, TVI, and 960H Video Output • Up to 30fps live view @ 1080p • MegaPixel IR Corrected 2.
PACKAGE CONTENTS Before installing the camera, please make sure that the following items are included in the box: 1. 2. 3. 4. Mighty Dome Trio Camera Accessories Wired remote controller Instruction Manual & Mounting Template If any of these materials are missing, please contact the vendor help desk immediately.
DISCLAIMER • • • • While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. Our reserves the right to change the specifications of the hardware and software described herein at any time without prior notice.
WARNING AND CAUTION WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.
FCC COMPLIANCE STATEMENT FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT.
IMPORTANT SAFEGUARDS 1. 2. 3. 4. 5. 6. Read these instructions. Heed all warnings. Follow all instructions. Do not use this equipment near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other equipment (including amplifiers) that produce heat. 8. Do not defeat the safety purpose of the polarized or grounding-type plug.
TABLE OF CONTENTS DISCLAIMER ................................................................................................................... 1 I. INSTALLATION AND CONFIGURATION....................................................................7 2.1 Installation ........................................................................................................................................ 7 2.2 Camera Control & Setup................................................................................
3.9.7 COLOR BAR .................................................................................................................................................................... 23 3.9.8 LANGUAGE ..................................................................................................................................................................... 23 3.9.9 CAM TITLE.................................................................................................................................
I. INSTALLATION AND CONFIGURATION 2.1 Installation 1) Dome Cover • Vandal Proof Domes - Use the provided Torx wrench to unscrew the vandal proof screws and remove the dome cover. • Indoor Domes - Turn the dome cover to the left to remove the dome cover. 2) Flush Mount Installation: • Using four St4x30 screws, attach the flush mount base to a sturdy surface. • Optional flush mount decorator plate.
2.
2.3 Varifocal, DC Auto Iris Lens Adjustments Loosen Zoom & Focus screws and make necessary adjustments as shown. Field of View: Telephoto (T) to Wide (W) Focus: Near (N) to Far (F) 2.
III. PROGRAM & OPERATION Main Menu FOCUS ADJ Sub Menu EXPOSURE SHUTTER BACKLIGHT DAY&NIGHT WHITE BAL DNR ADJUST MOTION SYSTEM LENS BRIGHTNESS SENS-UP AGC OFF HLC BLC WDR COLOR GAIN SHARNPESS GAMMA MIRROR FLIP D-ZOOM ACE DEFOG SHADING PRIVACY OFF ON COM.
Main Menu MENU FOCUS ADJ EXPOSURE BACKLIGHT DAY&NIGHT WHITE BAL DNR ADJUST MOTION SYSTEM EXIT OFF OFF EXT MIDDLE OFF 3.1 FOCUS ADJ Focus ADJ displays the input data from the FA Detector Mode in a Graphic Bar form. This function provides convenience to the user by allowing a more accurate focusing by utilizing a bar graph, there are 3 bars to adjust by Left, Center and Right. The left bar is for low contrast areas, the center is mid contrast and the Right is for high contrast areas.
3.2.1 LENS Using this function, you can control the screen brightness DC : Select Auto Iris Lens MANUAL : The shutter does not automatically move but is fixed to the maximum in this mode. 3.2.2 BRIGHTNESS Adjusts the video brightness.(0~20) 3.2.3 SHUTTER AUTO : Select this mode to control the shutter speed automatically. Shutter speed is automatically controlled depending on the brightness of the screen. (OUTDOOR / INDOOR / DEBLUR) MANUAL : You can select one of 12 options.
3.3.1 HLC BACKLIGHT LEVEL COLOR RETURN 10 ||||||||||||| BLK This function masks strong light to minimize white out due to over exposure and preserve much of the on-screen details when the camera sees a strong light source. LEVEL : 0 ~ 20 COLOR : BLACK, WHITE, YELLOW, CYAN, GREEN, MAGENTA, RED, BLUE 3.3.
3.3.3 WDR BACKLIGHT WEIGHT RETURN MIDDLE Wide Dynamic WEIGHT : LOW, MIDDLE, HIGH No support for CVBS. Range. 3.4 DAY&NIGHT 3.4.1 AUTO Optimized for standard cameras without IR DAY&NIGHT ANTI-SAT. AGC THRES AGC MARGIN DELAY RETURN 0 ||||||||||||| 3 ||||||||||||| 5 ||||||||||||| 3 ||||||||||||| 3.4.2 COLOR The picture is always displayed in color. 3.4.3 B&W The picture is always displayed in black and white.
DAY&NIGHT ANTI-SAT. RETURN 0 ||||||||||||| 3.4.4 EXT. DAY&NIGHT ANTI-SAT. EXTERN SW DELAY RETURN 0 ||||||||||||| LOW 3 ||||||||||||| Optimized for IR Cameras Anti Saturation This function automatically controls the brightness for saturated object from the IR light. It prevents saturation and expands dynamic range. Also saturation level can be controlled. 3.5 WHITE BAL Ability to set the WHITE BALANCE mode. 3.5.
3.5.4 MANUAL AWB C-TEMP R-GAIN B-GAIN RETURN 5000K 10 ||||||||||||| 10 ||||||||||||| Select this to fine-tune White Balance manually. Set White Balance first by using the C-TEMP mode. After that adjust the R-GAIN & B-GAIN mode, fine-tune the white balance. 3.6 DNR DNR reduces noise by amplifying gain in low light. (OFF, LOW, MIDDLE, HIGH) 3.
ADJUST COLOR GAIN SHARPNESS GAMMA MIRROR FLIP OFF D-ZOOM ACE OFF DEFOG SHADING PRAVACY RETURN 12 ||||||||||||| 5 ||||||||||||| 0.5 OFF 1.0X OFF OFF 3.7.1 COLOR GAIN The setting range is 0 ~ 20. The smaller the setting value the smaller the color gain gets and the image will lose most of the color. 3.7.2 SHARPNESS Select a mode to adjust the image’s sharpness. Increase or decrease the level. Too high of Sharpness more noise will appear in image. value.(0 ~ 20) 3.7.3 GAMMA The setting range is 0.45 ~ 0.7.
3.7.7 ACE This function is a local adaptive contrast enhancement. It uses a histogram analysis and tone mapping method in pixels domain. 3.7.8 DEFOG DEFOG MODE AUTO LEVEL MIDDLE RETURN You can use the defog mode to allow the camera to automatically detect the fog density of the scene and display a clear image despite smog, or general poor visibility. AUTO : Adjust the level automatically. MANUAL : Depending on the defog level set by the user, adjust the clarity of image.(LOW, MIDDLE, HIGH) 3.7.
BOX ZONE NUM ZONE DISPLAY H-POS V-POS H-SIZE V-SIZE CB LEVEL CR LEVEL TRANS RETURN 0 ON 12 2 3 3 10 ||||||||||||| 10 ||||||||||||| 2 POLYGON ZONE NUM ZONE DISPLAY POS0-X POS0-Y POS1-X POS1-Y POS2-X POS2-Y POS3-X POS3-Y CB LEVEL CR LEVEL TRANS RETURN 0 ON 80 5 88 5 88 13 80 13 10 ||||||||||||| 10 ||||||||||||| 2 ZONE NUM : You can select up to 16(8 for polygon) PRIVACY areas. ZONE DISPLAY : ON/OFF H(V)-POS, H(V)-SIZE, POS0(1,2,3)-X(Y) : Adjust the size and position or the selected area.
MOTION DET WINDOW SENSITIVITY MOTION OSD TEXT ALARM SIGNAL OUT RETURN 5 ||||||||||||| OFF OFF OFF This product generates signals each time an object movement is detected in the four areas of the screen so efficient monitoring can be achieved. 3.8.1 DET WINDOW DET WINDOW WINDOW USE WINDOW ZONE DET H-POS 0 DET V-POS 0 DET H-SIZE 60 DET V-SIZE 34 RETURN 0 ON WINDOW USE : You can select up to 4 MOTION areas. WINDOW ZONE : ON/OFF DET H(V)- POS(SIZE) : Adjust the size and position or the selected area. 3.8.
3.8.4 TEXT ALARM If an object moves in an area set by the user, it will be displayed on the screen as a message. 3.8.5 SIGNAL OUT Not supported. 3.9 SYSTEM SYSTEM COM. IMAGE RANGE FULL TVI OFFSET OFF EXSDI OFF FRAME RATE 1080_30p FREQ 60HZ COLOR BAR OFF LANGUAGE ENG CAM TITLE OFF RESET ON RETURN 3.9.1 COM.
COM. CAM ID BAUDRATE RETURN 1 9600 Not supported. 3.9.2 IMAGE RANGE This is Digital output data scale mode for adjusting the black level. Full : full digital data COMP : scaling down mode USER : user setting 3.9.3 TVI OFFSET If you use HD-TVI, you should change TVI OFFSET to ON. 3.9.4 EXSDI If you use EX-SDI, you should change EXSDI to ON. 3.9.5 FRAME RATE Indicates the number of fps(frame per second) available for the video stream configuration.(1080, 720) 3.9.6 FREQ Select depending on NTSC or PAL.
3.9.9 CAM TITLE This function allows the users to set the title of camera as well as the usage of on screen display of the title. 3.9.10 RESET Reset camera to factory settings.
APPENDIX A — SPECIFICATIONS Detailed Specifications VTD-M2HET2812 VTD-M2RHET2812 Image Sensor Sony® 1/2.8” STARVIS CMOS Image Sensor Video Output EX/HD-SDI / TVI / 960H Resolution 2.1 MegaPixel (1920p x 1080p) Effective Pixels 1920(H) x 1080(V) Lens Type MegaPixel IR Corrected 2.8-12mm Varifocal Electronic Iris 1/60 ~ 1/100,000sec DAY / NIGHT Mechanical IR Cut Filter (True Day/Night) Sensitivity Dynamic Intensity Smart IR LEDs 0.15 lux (Color) / 0.03 lux (B/W) 0.15 lux (Color) / 0.
Detailed Specifications VTD-MV2HET2812 VTD-MV2RHET2812 Image Sensor Sony® 1/2.8” STARVIS CMOS Image Sensor Video Output EX/HD-SDI / TVI / 960H Resolution 2.1 MegaPixel (1920p x 1080p) Effective Pixels 1920(H) x 1080(V) Lens Type MegaPixel IR Corrected 2.8-12mm Varifocal Electronic Iris 1/60 ~ 1/100,000sec DAY / NIGHT Mechanical IR Cut Filter (True Day/Night) Sensitivity Dynamic Intensity Smart IR LEDs 0.15 lux (Color) / 0.03 lux (B/W) 0.15 lux (Color) / 0.03 lux (B/W) / 0.
APPENDIX B — DIMENSIONS VANDAL DOMES 31 INDOOR DOMES 29
LIMITED LIABILITY WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.