Use and Care Manual

ManualsBrandsVITAL COAT ManualsConcrete CoatingsV-200 Protective 9 lb. Water Base Acrylic Epoxy Quick Drying Concrete Masonry and Stone Sealer

Table Of Contents

Description

Primary Applications

Vital Coat V-200 Protective Sealer is a high

performance water-based two Part Acrylic Epoxy system that will provide

an exceptional level of protection to many types of hard surfaces. Its unique formula is enhanced with cross linking

technology to achieve maximum protection in a short amount of time. Vital Coat’s

V-200 Protective Sealer with cross

linking technology enables the coatings to attach to concrete, stone, mortar, and clay tile substrates and will not peal,

flake or fade.

V-200 Protective Sealer with cross linking technology optimizes resistance to chemicals and abrasions.

It resists mold and mildew which is essentially a “self cleaning” surface, making routine maintenance very easy and

keeping your concrete looking fresh and clean. It is UV Stable and will not turn yellow. It will protect your concrete

against frost and salts while increasing its resistance to stains, acids, oils, and moisture. It is environmentally friendly,

non-toxic and non-flammable and does not contain hazardous components or release any VOC or noxious fumes.

Appearance

Vital Coat

V-200 Protective Sealer

Technical Data Sheet (TDS)

*Protection from Freeze-Thaw Deterioration

*Permanently seals, protects and waterproofs many surfaces

*Repels Oil Based Stains

*Mold and Mildew Resistant

*Will not peel, fade or flake

*UV Resistant, Non Yellowing

VOC Content

Re-Coat Time

Clear to translucent solution

Dry to Touch

Mild

50°F - 85°F

24 hours

<50g/L

2 hours

The coverage rate will vary depending upon surface porosity and application method use. The typical range is approximately 250 to

300 sq ft per gallon per application. Two applications are recommended with approximately 300 to 350 sq ft per gallon coverage . Avoid

excessive build up.

Coverage

Packaging

This product is available in 1, and 5 gallon containers. Other quantities available upon request.

1 to 2 hours

Odor

V-200 Protective Sealer is recommended for Interior or Exterior applications. It will provide a protective coating to new or aged

Concrete, Masonry, or Stone substrates. V-200 Protective Sealer will dry clear and will keep the natural look to your concrete while

providing an aesthetically pleasing light reflection and a smooth, finished look to the surface..

Features/Benefits

Technical Information

Note*Higher temperatures will speed up activation time and decrease the pot life of our component products. For every additional 10 degrees in temperature, your coating's pot life will generally decrease by half. The ideal temperature for use is 80 °F.

*Excellent Adhesion

*Keeps Concrete and Masonry Looking Fresh and Clean

Result

Property

Solids

20.00%

Application Temperature

Pot Life after Mixing Part A with Part B

Summary of content (6 pages)

PAGE 1
Vital Coat V-200 Protective Sealer Technical Data Sheet (TDS) Description Vital Coat V-200 Protective Sealer is a high performance water-based two Part Acrylic Epoxy system that will provide an exceptional level of protection to many types of hard surfaces. Its unique formula is enhanced with cross linking technology to achieve maximum protection in a short amount of time.
PAGE 2
Shelf Life This product has a shelf life of up to one year in its original, sealed, unopened container prior to any activator or catalyst being added. If product appears to be hardened or separated contact Vital Coat before use. Directions for Use Surface Preparation: Concrete surfaces must be dry, structurally sound, free of loose or deteriorated concrete and free of dust, dirt, paint, efflorescence, oil and all other contaminants. Do not apply if rain is in the forecast within 24 hours.
PAGE 3
SAFETY DATA SHEET Vital Coat V-200 Protective Sealer 1. PRODUCT AND COMPANY IDENTIFICATION Trade Name: V-200 Protective Sealer Manufacturer: Vital Holdings LLC. 2172 Arendell Way. Tallahassee, Florida. 32308 Telephone: Toll Free 844-284-2858 Chemical Name: Water Based Acrylic Copolymer Product Use: Concrete, Brick, Block, and Asphalt For emergency: Contact 911 For Non Emergency Health and safety Information contact: Toll Free 844-284-2858 2. COMPOSITION INFORMATION CHEMICAL AND COMMON CAS. NO.
PAGE 4
SAFETY DATA SHEET 4. FIRST AID MEASURES Eye Contact: Flush eyes with water for 15 minutes. Call a physician if irritation persists. Skin Contact: Remove contaminated clothing/shoes and wipe excess from skin. Wash with soap and water for 15 minutes. Get medical attention if irritation develops. Ingestion: If taken internally, rinse mouth, do not induce vomiting and Call a physician immediately. Inhalation: If irritation, headache, nausea or drowsiness occurs, remove to fresh air.
PAGE 5
SAFETY DATA SHEET Ventilation: Use with adequate ventilation. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance and Odor: Clear to slightly cloudy liquid with a mild acid odor. Boiling Point: 212°F Vapor Pressure: Same as water. Flash Point: Same as water. Solubility in Water: Soluble. Specific Gravity: 1.1 g/ml pH: Approximately 6.0 10. STABILITY AND REACTIVITY This material is stable. It is incompatibility with Alkaline Solutions which will cause product to solidify. Hazardous polymerization does not occur.
PAGE 6
SAFETY DATA SHEET HEALTH FLAMMABILITY REACTIVITY PERSONAL PROTECTION 4=Extreme 3=High 1 0 0 C 2=Moderate 1=Slight 0=Insignificant Vital Coat is a NxTech Holdings LLC Brand. The information contained in this Material Safety Data Sheet is furnished without warranty, expressed or implied. The information contained in this document is believed to be accurate and it is the best information available.