Instructions / Assembly

ManualsBrandsVITA ManualsAccessoriesVita 49" x 39" Vinyl Cottage Picket Wings, White, VA74338

1. Posts (2) 4”x 4“ x 54” (10 cm x 10 cm x 137 cm) - 10126

2. Top Rails (2) 2“ x 3.5” x 44.5“ (5 cm x 9 cm x 113 cm) - 10103

3. Bottom Rails (2) 2“ x 3.5” x 43.5“ (5 cm x 9 cm x 110 cm) - 10104

4. Pickets (4) Length 29.25“ (74 cm) - 10105

Pickets (2) Length 30“ (76 cm)- 10107

Pickets (2) Length 31.5“ (80 cm) - 10108

Pickets (2) Length 32.75“ (83 cm) - 10109

Pickets (2) Length 34.25“ (87 cm) - 10110

Pickets (2) Length 36.25“ (92 cm) - 10111

Pickets (2) Length 38.25“ (97 cm) - 10112

Pickets (2) Length 41“ (104 cm) - 10113

5. External Post Caps (2) 4” x 4” (10 cm x 10 cm) - 10735-1

6. Post Trim Caps (2) 4” x 4” (10 cm x 10 cm)- 10737-1

7. Base Moldings (2) 5” x 5” (13 cm x 13 cm) - BM20022

8. Rail Mount Brackets (8) 2” x 3.5” (5 cm x 9 cm)- 10045

Hardware Kit (Includes):

9. 5/8” (16 mm) Self-tapping stainless Screws (24) - 20016

10. 1 1/2” (38 mm) Stainless Steel Screws (8) - 20005

11. Rail end spacers (2) 2“ x 3.5” x .5” (5 cm x 9 cm x 13 mm)- 10217

12. Tube of vinyl cement (1) - 20000

Tools You Will Need

• Cordless Drill with #2 Phillips bit

• Tape measure

• Pencil

• Level

• Shovel

• Two bags of pre-mix concrete (optional)

General Information

• Read Instructions through carefully before beginning assembly.

• When handling components, place on a non-abrasive surface

(i.e. shipping box) to avoid scratching.

• We recommend an area approx 5’x 5’ (1.5 m x 1.5 m) for unobstructed handling.

Cottage Picket Wings

ASSEMBLY INSTRUCTIONS

V2.6/081020

Not to Scale

(13 cm)

5" (13 cm)

(20 cm)

39" (99 cm)

49"

(124 cm)

Please read through before starting assembly.

Check Box for These Contents (1 Box)

In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST).

18.75"

(48 cm)

44" (112 cm)

www.wearevita.com

Summary of content (5 pages)

PAGE 1
A S S E M B LY I N S T R U C T I O N S Cottage Picket Wings www.wearevita.com 44" (112 cm) 39" (99 cm) 18.75" (48 cm) 8" 5" (13 cm) (20 cm) 5" (13 cm) 49" (124 cm) Please read through before starting assembly. Check Box for These Contents (1 Box) In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST). 1. Posts (2) 4”x 4“ x 54” (10 cm x 10 cm x 137 cm) - 10126 2. Top Rails (2) 2“ x 3.5” x 44.
PAGE 2
Cottage Picket Wings Installation STEP ONE A A Lay out one of the posts (part 1). Measure 8” (20.3 cm) from one end of the post and put a mark. Center the rail mount bracket (part 8) on the post, with the open end at the 8” mark. Using two screws 5/8" (16 mm) , fasten the bracket to the post as illustrated. Repeat this for the second post. Note: All screws are self-tapping and require no pre-drilling. B Take one of the posts and measure 29” (73.7 cm) from the same end of the post as in step 1.
PAGE 3
STEP T WO A A Insert the bottom rail (part 3) into the bracket on the base molding. Make sure the holes in the rail are facing towards the second bracket on the post. Using one screw 5/8"(16mm), secure the rail in place through the side wall of the bracket as illustrated. Repeat this for the opposite side wall. Bottom Rail is only routed on the one side B Top rail is routed on both sides: The larger opening faces the bottom rail.
PAGE 4
STEP THREE A Determine which side of your arbor the wings will be attached to. Fasten a rail mount bracket to the outside of the arbor base molding in the same manner as described in Step 1 (c). Note: If your arbor does not have a base mold, install bracket directly on arbor (B). You will need to use 1/2” (13 mm) filler (A) as bottom rail is shorter to allow for base mold. B Using two 5/8" (16 mm) screws, fasten a second bracket to the outside of the arbor post as illustrated.
PAGE 5
Vinyl glue is to be applied below the picket level. STEP FOUR B A Lower the wing post into the hole, while slipping each rail end into the corresponding bracket on the arbor post. check the top rail for level, and adjust the depth of the hole if needed. Secure the rail ends to the brackets as described in Step 2 (a), and fill in the hole (for added stability, use pre-mix concrete). Repeat this step for the opposite wing panel.