User Manual

ManualsBrandsVisonic ManualsElectronicsWireless 2-way keyfob

D-302416 1

KF-234 PG2

Wireless PowerG 2-Way Keyfob

Installation Instructions

1. INTRODUCTION

KF-234 PG2 is a miniature PowerG 4-button (6-function) keyfob,

designed for use with the PowerMaster-10.

Transmission is initiated by pressing any one of the four recessed

pushbuttons. Upon pressing a specific button, the KF-234 PG2

transmits a PowerG message associated with the button that was

pressed and identifiable by PowerMaster-10 control panels.

A red LED lights during transmission. When an identified command is

received by the PowerMaster-10 control panel, it acknowledges the

command. Upon acknowledgement, the green LED lights and a

happy beep is heard to indicate successful completion of the

command or the red LED lights and a sad beep is heard to indicate

that the control panel cannot perform the command.

In addition, a battery report is transmitted

with

the outgoing message. PowerMaster-

10 control panels are designed to identify

this report and operate a corresponding

output, if required.

Each keyfob is supplied with a small key

ring.

Operating power is obtained from an

internal 3V Lithium battery.

Figure 1:

External View

2. SPECIFICATIONS

Frequency Band (MHz): Europe: 433, 868, USA: 915

Modulation: GFSK

Antenna:

Built-in helical antenna.

Communication Protocol: PowerG.

Battery type: 3V CR-2032 Lithium battery.

Caution!

Risk of explosion if battery is replaced by an incorrect type. Dispose

of used battery according to manufacturer's instructions.

Battery Life Expectancy

8 years (for typical use)

Power Supply: Type C

Note: If transmission is still possible despite the battery condition, the

unit will send a low battery signal to the control panel.

Transmitted Messages:

Arm Away, Arm Home, Arm Latchkey,

Disarm, AUX and Panic.

Operating Temperature: 0° to 55°C (32° to 131°F).

Humidity: Average relative humidity of approximate 75% non-

condensing. For 30 days per year relative humidity may vary between

85 % and 95 % non-condensing.

Dimensions:

60 x 34.5 x 12.5 mm

(2-3/8 x 1-3/8 x 1/2 in.).

Weight (including battery) : 25 g (0.9 oz).

Color: Black

Compliance with Standards:

Europe:

EN 300220, EN 50131-1 Grade 2, Class II and (EN 50134-2

Class II if used for social alarm), EN 301489, EN 50130-4, EN 60950,

EN 50131-6

USA:

CFR47 Part 15

Canada: RSS 210

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1)

This device may not cause harmful interference, and

(2)

this device must accept any interference received, including

interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for

help.

Warning!

Changes or modifications to this equipment not expressly

approved by the party responsible for compliance (Visonic Ltd.)

could void the user’s authority to operate the equipment.

This equipment complies with FCC RF radiation exposure limits

set forth for an uncontrolled environment.

3. ENROLLMENT

Refer to the PowerMaster-10 Installer Guide for the device enrollment procedure.

4. MODIFY DEVICE SETTINGS

This section describes how to configure the parameters for home monitoring of people from the PowerMaster-10 control panel.

To Modify the Keyfob Device Settings

Refer to the PowerMaster-10 Installer Guide and perform the procedure for Adding A Wireless Device (section 4.5.2), or, Modifying a Device

(section 4.5.5). Then continue below to modify the device settings.

DEV SETTINGS

Summary of content (4 pages)

PAGE 1
KF-234 PG2 Installation Instructions Wireless PowerG 2-Way Keyfob 1. INTRODUCTION KF-234 PG2 is a miniature PowerG 4-button (6-function) keyfob, designed for use with the PowerMaster-10. Transmission is initiated by pressing any one of the four recessed pushbuttons. Upon pressing a specific button, the KF-234 PG2 transmits a PowerG message associated with the button that was pressed and identifiable by PowerMaster-10 control panels. A red LED lights during transmission.
PAGE 2
Here you select the function of the AUX button on the KF-234 PG2 keyfob. AUX A 2. instant 3.  Select between "instant", "skip exit delay" and "PGM". or 4. AUX A When exiting "ZONES / DEVICES" menu the PowerMaster-10 system displays the number of devices that need to be updated, as follows: DEV UPDATING NNN. For detailed instructions on Adding Devices, Deleting Devices, Replacing Devices and Defining Defaults see the PowerMaster-10 Installer Guide. 5.
PAGE 3
stated in the control panel’s instruction manual. 8. MISCELLANEOUS COMMENTS 8.1 Product Limitations Visonic Ltd. wireless systems are very reliable and are tested to high standards. However, due to their low transmitting power and limited range (required by FCC and other regulatory authorities), there are some limitations to be considered: 3 A. Control panels may be blocked by radio signals occurring on or near their operating frequencies, regardless of the code selected. B.
PAGE 4
WARRANTY Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the “Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve (12) months from the date of shipment by the Manufacturer.