Installation Instructions

ManualsBrandsVisonic ManualsElectronicsMotion Detector

DE3582 1

K-980W

K-980WK-980W

K-980W

Pet-immune Wireless PIR Motion Detector

Installation Instructions

1. FEATURES

1. FEATURES1. FEATURES

1. FEATURES

• Uses TSI™ (Target Specific Imaging) technology for

distinction between humans and pets

• Immune to pets weighing up to 36 kg (80 lb)

• Integral swivel bracket for wall or ceiling installation

• Sealed chamber protects the optical system

• On-board CE and FCC approved transmitter

• Programmable pulse counter (1, 2, 3 or 5 pulses)

• 9 Volt battery powered, with unique energy saving

circuitry

• Extremely-low current consumption – 0.013 mA

• Automatically inhibited after detecting motion; reverts to

the ready state if no motion is detected for 2 minutes.

• A TEST/NORMAL selector eliminates the 2-minute inhibit

period and sets the pulse counter to 1-pulse during walk

testing.

• Automatic transmission of low-battery and tamper alerts

• Three-position vertical adjustment

• White light protection

• Programmable 8-bit system code and 4-bit channel code

• Surface and corner mounting

• Rejects RF interference up to 1000 MHz

• Elegantly styled, sturdy case

• Keyhole-shaped slot for easy removal of PCB

Figure 1. The K-980W Wireless Detector

2. SPECIFICATIONS

2. SPECIFICATIONS2. SPECIFICATIONS

2. SPECIFICATIONS

OPTICAL

Max. Coverage Range: 9 x 9 m (30 x 30 ft) / 90

Pet Immunity: Immune to pets weighing up to 36 kg (80 lb)

under optimal environmental conditions.

Vertical Adjustment: 3-position adjustment scale: 1.8 m (6 ft),

2.1 m (7 ft) and 2.4 m (8 ft).

ELECTRICAL

Voltage: 9 Volt alkaline or lithium battery.

Standby Current: 0.013 mA.

LED: Walk Test & transmission.

Detector: Dual-element low-noise pyroelectric sensor.

Pulse Counter: Programmable to 1, 2, 3 or 5 pulses with walk-test

override.

Inhibit Timer: re-enables the unit about 2 minutes after alarm, if

no further motion is detected.

WIRELESS

Frequency (MHz): 315, 304, 404, 418, 433.92 or other

frequencies according to local requirements.

Alarm Transmission Duration: 2 seconds.

Encoding: 8-bit digital word, 256 combinations, pulse width

modulation.

Channels: 4 channels, switch selectable.

Battery Test: Automatic transmission of "Code 0" at 2-minute

intervals if the battery voltage drops below 7 V.

Tamper Alert: Transmission of the "Channel 2" code at 2-minute

intervals, until the tamper switch is restored.

ENVIRONMENTAL

Operating Temperature: -10°C to 50°C (14°F to 122°F).

Storage Temperature: -20° to 60°C (-4°F to 140°F).

RFI Protection: Greater than 30 V/m up to 1000 MHz.

Note: The temperature range may be reduced due to battery

characteristics.

Compliance with Standards: Meets FCC Part 15 requirements;

The 433.92 MHz version complies with the European Council

Directive EMC 89/336/EEC & 92/31/EEC, and bears the CE mark

and certification.

MOUNTING

Height: 1.8 to 2.4 m (6 to 8 ft)

Installation Options: Surface or corner (without bracket);

surface or ceiling (with bracket).

Bracket Adjustment: 20

° downward (only in non-pet immune

applications), 20

° left and right.

PHYSICAL

Dimensions (H x W x D): 117 x 65 x 47 mm.

(4-5/8 x 2-9/16 x 1-7/8 in.).

Weight: 92 g (3.25 oz) without bracket, 107 g (3.8 oz) with bracket.

Color: White

Summary of content (5 pages)

PAGE 1
K-980W Installation Instructions Pet-immune Wireless PIR Motion Detector 1.
PAGE 2
3. INSTALLATION 3.1 Installation Hints and remove it via the “keyhole” (see Figure 4). Important! Under optimal environmental conditions, the detector is immune to animals weighing up to 36 kg (80 lb) that move on the floor or climb on furniture, as long as this activity takes place below 1 m (3 ft). Above 1 m (3 ft), the detector is immune to pets weighing 18 kg (40 lb), but the pet immunity will decrease as the pet gets closer to the detector.
PAGE 3
Figure 6. Wall and Ceiling Positions of Bracket 6th.Press the bracket against the mounting surface and mark the points for drilling. Drill out the holes and insert plastic anchors. 7th.Attach the bracket to the mounting surface using the two screws supplied. H. Swivel the detector horizontally to face the desired direction, but do not tilt it if this is a pet immune application. However, if pets are not present it is advisable to tilt the detector as much as 20° down.
PAGE 4
B. Pet-Free Locations To obtain the best coverage possible where no pets are present, mount the detector with the integral bracket at any desired height between 1.8 m (6 ft) and 2.4 m (8 ft). Then set the vertical adjustment scale to the 2.4 m (8 ft) position and tilt the detector 20° down. 3.9 Setting the TST/NORM Jumper Since battery saving is of utmost importance in normal use of the detector unit, an automatic timer inhibits the detector for approximately 2 minutes after each transmission.
PAGE 5
merchantability or fitness for a particular purpose, or otherwise. In no case shall the Manufacturer be liable to anyone for any consequential or incidental damages for breach of this warranty or any other warranties whatsoever, as aforesaid. This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the Product only.