User's Manual

ManualsBrandsVisonic ManualsElectronicsPIR Transmitter

DE3637 1

KK--980MCW 980MCW

Pet-Immune PowerCode Wireless PIR Detector

Installation Instructions

1. INTRODUCTION1. INTRODUCTION

The K-980MCW is a pet-immune, fully supervised ultra low-

current wireless PIR that incorporates a PowerCode transmitter.

Both transmitter and detector circuits are powered by an on-

board, long life 3.6 V Lithium battery.

As a pet immune motion detector, the K-980MCW utilizes TSI™

(Target Specific Imaging) technology that ensures immunity to

pets weighing up to 36 kg (80 lb).

As a supervised wireless detector, the K-980MCW has a 24-bit ID

code, randomly selected in the factory from over 16 million possible

combinations. Compatible PowerCode receivers are designed to

"learn" specific IDs and respond only to them.

Following detection of a human intruder, the K-980MCW triggers

the on-board transmitter which transmits its specific PowerCode

ID followed by an alarm signal and status designators for

tampering and battery condition. Alarm and other data are thus

forwarded to the alarm control panel or to a head-end computer,

depending on the type of system in which the detector is used.

After triggering the transmitter, the K-980MCW inhibits itself to

save battery power. The detector reverts to the ready state 2

minutes after the last movement has been detected. An LED/

WALK-TEST jumper is used to override the 2-minute rearm timer

during walk testing.

Since messages transmitted by the

K-980MCW might collide with

those transmitted by other Power-

Code transmitters, an anti-collision

transmission sequence is used.

A programmable pulse counter is

included in the unit for maximum

immunity against false alarms.

A periodic test transmission for

supervision purposes takes place

automatically once an hour. The

receiver is thus informed that the

Figure 1. General View

particular detector is taking an active part in the wireless network.

2. 2.

SPECIFICATIONSSPECIFICATIONS

OPTICAL

Max. Coverage Range: 12 x 12 m

(40 x 40 ft) / 90°

Pet Immunity: Animals up to 36 kg

(80 lb) - not verified by UL.

Vertical Adjustment: 3-position

adjustment scale: 1.8 m (6 ft),

2.1 m (7 ft) and 2.4 m (8 ft).

ELECTRICAL

Battery Type: 3.6 Volt lithium

thionyl chloride (LiSOCl

) battery,

size 1/2AA, Tadiran TL-2150

Nominal Battery Capacity: 1 Ah

Standby Current Drain: 0.015 mA

Transmit Current Drain: 12 mA

(including LED)

Figure 2. Coverage Pattern

Battery Life Expectancy (not verified by UL): 3 years (for

typical use).

LED: Lights for 2 seconds upon transmission and upon motion

detection in the walk test mode.

Detector: Dual-element low-noise pyroelectric sensor.

Pulse Counter: Programmable to 1, 3 or 5 pulses.

Inhibit Time: 2 minutes after last alarm (none during walk test)

WIRELESS

Frequency (MHz): 315, 433.92, 868.95, 869.2625 according to

local requirements. UL has only investigated at 315 MHz.

Transmission Sequence: 3 data bursts at variable intervals within

3 seconds.

Encoding: 24-bit ID, over 16 million possible combinations.

Total Message Length: 36 bits

Battery Supervision: Automatic reporting of low-battery status

with each alarm and with periodic autotest.

Tamper Alert: Reported at 3-minute intervals

ENVIRONMENTAL

Operating Temperature: -10° to 49°C (14° to 120°F).

Storage Temperature: -20° to 60°C (-4°F to 140°F).

RFI Protection: > 30 V/m up to 1000 MHz

Compliance with Standards: Meets FCC Part 15, MPT1349 and

Directive 1999/5/EC.

This device complies with the essential requirements and

provisions of Directive 1999/5/EC of the European Parliament and

of the Council of 9 March 1999 on radio and telecommunications

terminal equipment.

PHYSICAL

Size (H x W x D): 117 x 65 x 47 mm (4-5/8 x 2-9/16 x 1-7/8 in.).

Weight: 97 g (3.4 oz) without bracket. 112 g (4 oz) with bracket.

Color: White.

3. 3.

INSTALLATIONINSTALLATION

3.1 Installation Tips

To minimize false alarms, follow these guidelines:

Do not aim at heat sources Mount on solid, stable surfaces

Summary of content (5 pages)

PAGE 1
K-980MCW Pet-Immune PowerCode Wireless PIR Detector Installation Instructions 1. INTRODUCTION The K-980MCW is a pet-immune, fully supervised ultra lowcurrent wireless PIR that incorporates a PowerCode transmitter. Both transmitter and detector circuits are powered by an onboard, long life 3.6 V Lithium battery. As a pet immune motion detector, the K-980MCW utilizes TSI™ (Target Specific Imaging) technology that ensures immunity to pets weighing up to 36 kg (80 lb).
PAGE 2
Do not expose to air drafts Do not install outdoors Prevent direct sunlight from reaching the detector Keep wiring away from electrical power cables Figure 4. Inside View Do not install behind partitions The unit must be installed so that the expected motion of a intruder would be perpendicular to the zones of detection. Important! The detector is immune to 36 kg (80 lb) animals moving on the floor or climbing on furniture as long as the activity takes place below 1 m (3 ft).
PAGE 3
rd. Press the tamper switch once and release it. This will perform the reset necessary for smooth power up. 4th. Put the cover on and watch the LED. It will flash once in 2 seconds for at least 15 seconds until the sensor stabilizes. 3.3 Enrolling the Transmitter ID into the Target Receiver’s Memory Refer to the target receiver’s installation instructions and follow the procedure given there for “teaching” transmitter IDs. It is much easier to carry out this operation in close proximity to the receiver.
PAGE 4
3.8 Walk Testing IMPORTANT! The range and the coverage area of the unit should be checked at least once a year. To assure proper continuous functioning, the end user should be instructed to perform a walk test at the far end of the coverage pattern prior to each time the alarm system is armed. To save battery power in normal use, an automatic timer inhibits the detector for approximately 2 minutes after transmitter activation.
PAGE 5
APPENDIX A. THE VISONIC LTD. POWERCODE SYSTEM A-1. The PowerCode Message Format The PowerCode message transmitted by the K980MCW includes the detector's 24-bit ID and a status report (see Fig. A1). Figure A1. Transmitted Data A message includes the following data: • Detector's ID: Any message transmitted starts with the 24bit ID assigned to the particular detector unit. • Tamper / Restore: Upon removal of the unit's front cover, a message will be transmitted with a "tamper marker" ON.