Installation and Operating Instructions

ManualsBrandsVisonic ManualsElectronicsHeat Detector

HTD-432 PG2 (915-0:025)/HTD-432 PG2

(868-0:025) /HTD-432 ME PG2 (868-

0:025) wireless heat detector

Installation and operating instructions

Read this instruction sheet thoroughly before installation and use of the HTD-432/HTD-432 ME PG2

Note: The reference to HTD-432 PG2 throughout this manual is also applicable to the other

models unless stated differently.

Introduction

The HTD-432 PG2 is a wireless heat detector with a fixed temperature, a rate of rise heat

sensor, and an internal piezoelectric alarm. The following versions are available:

Frequency (MHz)

Version

915

HTD-432 PG2 (915-0:025)

868

HTD-432 PG2 (868-0:025)

868

HTD-432 ME PG2 (868-0:025)

Compatible devices

This detector is compatible with UL/ULC Listed DSC

Control Panels and Qolsys IQ Panel 2+. For UL/ULC

installations use this device only in conjunction with

compatible IQ2 wireless receivers and PowerG

receivers. Transmissions occur at approximately 915

MHz (912 MHz to 919 MHz).

Operation

During normal operation, the green LED flashes every 12 seconds.

The detector goes into alarm when the heat level exceeds 135 ºF / 57.5 ºC and automatically

restores when the heat level falls below the threshold. The detector also goes into alarm

when the temperature rapidly increases over a short period of time. During an alarm, the

LED flashes once per second and the sounder emits the evacuation temporal pattern.

Detector trouble

If the detector has a general fault, the yellow LED blinks once every four seconds and

emits a chirp every 48 seconds. After four hours, the panel displays a fire trouble message.

Table: Detector and Status Indication

Status

LEDs

Sounder

Normal

Green flash every 12 seconds

Off

Heat Alarm

Red flash every 1 second

ANSI S3.41 temporal 3

Heat Test

Red flash every 1 second

ANSI S3.41 temporal 3

Test Alarm

(button

press)

Red flash every 1 second

ANSI S3.41 temporal 3

Detector

Trouble

Yellow flash every 4 seconds

One chirp every 48 seconds

Low Battery

Yellow flash every 12 seconds

One chirp every 48 seconds

(press button to hush for 12 hours)

Power-up

Red, yellow, green, flash sequence

One chirp at the end of the power-up

sequence

Tamper

Red, yellow, green flash sequence every

12 seconds

Off

Summary of content (10 pages)

PAGE 1
Operation During normal operation, the green LED flashes every 12 seconds. The detector goes into alarm when the heat level exceeds 135 ºF / 57.5 ºC and automatically restores when the heat level falls below the threshold. The detector also goes into alarm when the temperature rapidly increases over a short period of time. During an alarm, the LED flashes once per second and the sounder emits the evacuation temporal pattern.
PAGE 2
Wireless transmissions Battery Installation and replacement A supervisory message is transmitted at 128-second intervals. If the signal is not received, the control panel determines that the detector is missing. The detector transmits the following: • Idle (normal operation): The detector is in normal state without any faults or alarms. • Heat Alarm: Active when the detector is above 135°F (57.5°C) or the rate of rise of temperature is above 15°F/min (8.3°C/min).
PAGE 3
Installation instructions Select an accessible location that is not prone to tampering or accidental damage. The heat detector must be installed and maintained in accordance with the National Fire Protection Association’s Standards (NFPA 72), the National Electrical Code and all local fire and electrical requirements. The mounting surface should be relatively flat and capable of accepting screws or anchors. The detector is to be installed in an indoor dry location.
PAGE 4
restore activations. NOTE: The detector will not enter an alarm state when other internal faults are present. Owner's Instructions Testing the detector Follow the test procedure described here or contact your dealer or installer for test in g instructions. It is recommended to test the entire alarm system at least once a week to verify the operation of all system functions. Detector unit test To test the detector only, press and hold the Test button for less than five seconds.
PAGE 5
• • • • Humidity: 5 % - 93 % RH, non-condensing Voltage: 3V DC Approved Batteries: One battery: Panasonic CR123A or Duracell DL123A Supervisory Transmission Frequency: 128-second intervals WARRANTY Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the “Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve (12) months from the date of shipment by the Manufacturer.
PAGE 6
END-USER LICENSE AGREEMENT IMPORTANT - READ THIS END-USER LICENSE AGREEMENT ("EULA") CAREFULLY BEFORE OPENING THE DISK PACKAGE, DOWNLOADING THE SOFTWARE OR INSTALLING, COPYINGOR OTHERWISE USING THE SOFTWARE. THIS EULA IS A LEGAL AGREEMENT BETWEEN YOU AND VISONIC LTD. (“TYCO”) AND GOVERNS YOUR USE OF THE SOFTWARE ACCOMPANYING THIS EULA, WHICH SOFTWAREINCLUDES COMPUTER SOFTWARE AND MAY INCLUDE MEDIA, PRINTED MATERIALS, AND "ON-LINE" OR ELECTRONIC DOCUMENTATION (COLLECTIVELY, THE "SOFTWARE").
PAGE 7
g. 4. 5. Trademarks. This EULA does not grant you any rights in connection with any trademarks or service marks of Tyco, its affiliates or its suppliers. h. Rental. You may not sublicense, rent, lease or lend the Software. You may not make it available to others or post it on a server or web site or otherwise distribute it. i. Software Keys. The hardware/software key, where applicable, is your proof of license to exercise the rights granted herein and must be retained by you.
PAGE 8
Regulatory Information The device HTD-432 PG2 has a recommended service life of 10 years under normal conditions of use. Please refer to the label applied to the device indicating the recommended replacement year. This manual shall be used in conjunction with the Installation Manual of the alarm control panel. All the instructions specified within that manual must be observed. Frequency band Maximum power 868.0 MHz - 868.6 MHz 14 mW / 11.46 dBm 868.7 MHz - 869.2 MHz 14 mW / 11.
PAGE 9
Product documentation HTD-432 PG2 (915-0:025)/HTD-432 PG2 (868-0:025)/HTD-432 ME PG2 (868-0:025) wireless heat detector To download the full manual for this product, go to https://www.visonic.com/download-center or scan the QR code. FCC COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules and with ISED license-exempt RSS standard(s).
PAGE 10
Conditions to Void Warranty: This warranty applies only to defects in parts and workmanship relating to normal use of the Products.