CS-1600P POWERED SPEAKERS OWNERS MANUAL www.visionaudiovisual.
DECLARATION OF CONFORMITY Where applicable Vision products are certified and comply with all known local regulations to a ‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all applicable certification standards for sale in the EU and other participating countries. The product described in this owner manual is in compliance with RoHS (EU directive 2002/95/EC), and WEEE (EU directive 2002/96/EC) standards.
USE ONLY DOMESTIC AC OUTLETS Connecting the unit to an outlet supplying a higher voltage may create a fire hazard. HANDLE THE POWER CORD WITH CARE Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself. Pulling the cord may damage it. If you do not intend to use your unit for any considerable length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and try to avoid dropping heavy objects on it. Do not tie a knot in the power cord.
INSTALLATION 1. REMOVE GRILLES Push clamps up. The tip of the screw will push the grille up and off. 2. CUT HOLE IN CEILING TILE Diameter 222 mm (8.74”) 3. FIT LOUDSPEAKERS TO CEILING TILE Fix loudspeaker from the bottom of the ceiling tile and turn clamps out to hold in place.
4. FIX LOUDSPEAKERS TO CEILING TILE turning clamp screws from the front of loudspeaker. The clamps will turn out and tighten. 5. CONNECT LOUDSPEAKERS TOGETHER Use the included speaker cable. If cable provided is not long enough use unshielded speaker cable with gauge of 0.75mm or higher. “SPEAKER OUTPUT” Slave Loudspeaker 6. Master Loudspeaker CONNECT INPUT Plug the phoenix-to-minijack/phono adaptor (shown below) into the input connectors on the rear panel.
Note 1: Smartphones, laptops, DVDs etc connect to this input from their headphone or line-level output jacks. Note 2: If you will use only the Bluetooth input ignore this step. Input connector Power Input 7. CONNECT POWER Connect power into rear of master loudspeaker. 8. *OPTIONAL* CONNECT MORE SETS OF CS-1600P If using more than one pair of loudspeakers in the room link them together by connecting the Audio output connector to the audio input on the second pair.
STATUS INDICATORS On the master loudspeaker a solid light indicates that power is on and that an input is selected: YELLOW: Cabled input selected BLUE FLASHING: Bluetooth pairing activated (cabled input still selected) BLUE NOT FLASHING: Bluetooth input selected REMOTE CONTROL 1 4 2 5 3 1. 2. 3. 4. 5. 6.
OPERATION 1. TURN ON/OFF This product will come on automatically when power is turned on. Or use the remote control to turn on. The product will always resume the last input and volume level. NOTE: The IR receiver is built into the front of the master loudspeaker. The master loudspeaker has lights on the front panel, the slave does not. 2. SELECT BLUETOOTH INPUT a. Turn loudspeakers ON or select Bluetooth on remote control. The blue light starts to flash to show it is in pairing mode.
RS-232 CODES This product can be controlled with the included remote control or by a professional AV control system using RS-232 codes.
65 AC AC Volume Step 12 65 AD AD Volume Step 13 65 AE AE Volume Step 14 65 AF AF Volume Step 15 65 B0 B0 Volume Step 16 65 B2 B2 Volume Step 18 65 B3 B3 Volume Step 19 65 B4 B4 Volume Step 20 65 B5 B5 Volume Step 21 65 B6 B6 Volume Step 22 65 B7 B7 Volume Step 23 65 B8 B8 Volume Step 24 65 B9 B9 Volume Step 25 65 BA BA Volume Step 26 65 BB BB Volume Step 27 65 BC BC Volume Step 28 B5 B1 B1 Volume Step 17 A command is structured of 65 then the command twice e.g.
Table 2: Return Codes To request status send 65 65 65 Function Name Function STANDBY Range Remark working off standby 0 1 1 0 0 0 1 1 MUTE Mute status 0 1 BD3490FV_SELECT Input select 0 2 BD3490FV_GAIN_GET Get volume 1 28(1C) 1~28, volume has 28 steps BD3490FV_B_GAIN_GET Get bass gain 1 15(0F) Bass gain has 15 steps BD3490FV_T_GAIN_GET Get treble gain 1 15(0F) Treble gain has 15 steps BT_BIT Bluetooth status 0 1 Connected = 1 Disconnected = 0 Baud rate: 9600K Stop
TROUBLESHOOTING If your system is not operating properly, please refer to the following information. Problem Correction No power light Check power source and power input cable Check fuse in power cable plug Check battery in remote Power light on but no sound Hum or noise Turn the volume up with remote. Make sure the output volume on your test device is at full and that it works through the built-in device loudspeakers. Check that all input cables shielded properly.
SPECIFICATIONS PRODUCT DIMENSIONS: 260 x 180 mm / 10.2″ x 7.1″ (diameter x height for each speaker) CUTOUT SIZE: 222mm / 8.74″ PRODUCT WEIGHT: 4.9 kg / 10.8 lb (per pair) CONSTRUCTION MATERIAL: Plastic (ABS) + Sheet metal back can COLOUR: White TECHNICAL DETAILS: Amplifier Output: 2 x 30 watts (RMS) Woofer: 4″ Tweeter: 1.
WARRANTY This product comes with a 2-year return to base warranty, effective from the date of purchase. This warranty applies only to the original purchaser and is not transferable. For the avoidance of doubt, this will be taken from the information held by the appointed national distributor at the point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to notify the national distributor via your AV reseller.