Product Card

ManualsBrandsViper ManualsElectronicsWiFi Module

Model Number: VDWIFI-RT2

Features

• IEEE 802.11 b/g/n Compliant Transceiver

• ARM KM4 32-bit CPU

• Integrated 32Mbit serial flash

• UART/GPIO interfaces to Host Controller

• Integrated PCB trace antenna

• Input voltage range: 4.0V to 21.0V (See

variant table)

• FCC certified

RF/Analog

• Frequency Range: 2.4GHz ISM radio

band

• Channels: 1-13

• Modulation: DSSS, OFDM for WLAN

Package

• Plug-in daughter card with onboard

10pin receptacle (standard)

• Other connector and interface options

available

• Compact Module design

Applications

• Consumer Electronics

• iOT

• Industrial Controls

• Remote Device Management

• Fitness and Health Care

• White Goods / Appliances

• Gateways / Bridges

• Home Automation

Options

• Apple HomeKit Support

Onboard MFi co-processor

Custom firmware to support

specific HomeKit services & characteristics

•Amazon Akexa Support

•Google Home Support

•Integration of custom application firmware

Summary of content (11 pages)

PAGE 1
Model Number: VDWIFI-RT2 Features • IEEE 802.11 b/g/n Compliant Transceiver • ARM KM4 32-bit CPU • Integrated 32Mbit serial flash • UART/GPIO interfaces to Host Controller • Integrated PCB trace antenna • Input voltage range: 4.0V to 21.0V (See variant table) • FCC certified RF/Analog • Frequency Range: 2.
PAGE 2
Ordering P/N: PN HomeKit Input Power Input Connector Host Interface Connectivity VDWIFI-RT2 Y 4V - 21V 10 Pin UART Ayla Connector Pin-out (10-position receptacle): Pin No.
PAGE 3
FCC ID and IC Number for this product is as follows FCC ID:2AB7YVDWIFIRT2 IC: 20699-VDWIFIRT2 Note Changes or modifications to this device not expressly approved by Viper Design LLC could void the user's authority to operate the equipment. Labels Host Device must contain the following label on the outside of the unit: Contains FCC ID: 2AB7YVDWIFIRT2 Contains IC: 20699-VDWIFIRT2 General Statements (1) PCB antenna with maximum gain is -3.21 dBi.
PAGE 4
FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
PAGE 5
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 6
IC Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Radiation Exposure Statement This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment.
PAGE 7
Any company of the host device which install this modular with Single modular approval should perform the test of radiated emission and spurious emission according to RSS-247 requirement, Only if the test result comply with RSS-247 requirement，then the host can be sold legally. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada .
PAGE 8
OEM INTEGRATION INSTRUCTIONS: This device is intended only for OEM integrators under the following conditions: The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal on-board antenna that has been originally tested and certified with this module. External antennas are not supported.
PAGE 9
List the FCC/IC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B/ICES-003) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.
PAGE 10
width,shape(s), dielectric constant, and impedance as applicable for each type of antenna); b) Each design shall be considered a different type (e.g.
PAGE 11
Explanation: The EUT has a PCB Antenna, and the antenna use a permanently attached antenna which is unique. 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC/IC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating “Contains FCC ID” with their finished product. See Guidelines for Labeling and User Information for RF Devices – KDB Publication 784748.