Vincent Bedienungsanleitung deutsch Instructions for use english Manuel d‘utilisation français SP-998 Mono-Endverstärker mit Class-A-Schaltung Class A Monaural Power Amplifier Amplificateur mono Classe A
Sehr geehrter Kunde, wir danken Ihnen für das Vertrauen, welches Sie uns durch die Entscheidung für dieses hochwertige AudioProdukt, das Ihrem hohen Anspruch an Klang- und Verarbeitungsqualität gerecht wird, entgegenbringen. Auch wenn Sie verständlicherweise sofort beginnen wollen, das Gerät zu verwenden, lesen Sie bitte vor dem Aufstellen und Anschließen dieses Handbuch sorgfältig durch.
INHALTSVERZEICHNIS/CONTENTS/SOMMAIRE Sicherheitshinweise Weitere Hinweise Lieferumfang Beschreibung des Gerätes Installation Bedienung des Gerätes Weitere Tipps Fehlertabelle Technische Daten Lexikon/Wissenswertes 4 5 6 6 9 15 16 17 18 19 deutsch Safety guidelines Other instructions Included in delivery Description of the appliance Installation Operating the appliance Tips Search for errors Technical Specifications Glossary 20 21 22 22 25 31 32 33 34 35 english Consignes de sécurité Autres consignes Con
SICHERHEITSHINWEISE Dieses Gerät wurde unter strengen Qualitätskontrollen gefertigt. Es entspricht allen festgelegten internationalen Sicherheitsstandards. Trotzdem sollten folgende Hinweise vollständig gelesen und beachtet werden, um eine Gefährdung zu vermeiden: Das Gerät nicht öffnen! Gefahr des elektrischen Schocks! Es befinden sich keine vom Benutzer zu wartenden Teile im Gerät.
WEITERE HINWEISE Aufstellen des Gerätes Die Art der Aufstellung der Anlage hat klangliche Auswirkungen. Stellen Sie diese deshalb nur auf eine dafür geeignete, stabile Unterlage. Um das Klangpotential Ihres Systems optimal auszunutzen, empfehlen wir, die Geräte auf Vincent Racks zu platzieren und nicht aufeinander zu stellen.
LIEFERUMFANG Bitte prüfen Sie den Inhalt der Verpackung, diese sollte zusätzlich zum Gerät folgendes Zubehör enthalten: • 1 Netzkabel • 1 Kabel für die Einschaltsteuerung (“POWER CONTROL“) • dieses Handbuch BESCHREIBUNG DES GERÄTES Die Vincent-Entwickler fühlen sich nicht nur der Stereo-Tradition verpflichtet, auch für Mehrkanaltonanlagen und Heimkinos werden langlebige und überlegene Komponenten hergestellt.
VORDERANSICHT 2 1. POWER: Netzschalter Schaltet das Gerät ein und in die Bereitschaft. Im ausgeschalteten Zustand bestimmt das am „POWER CONTROL“-Anschluss anliegende Signal, ob das Gerät aktiv oder in Bereitschaft ist. 2. POWER-LED Leuchtet, solange das Gerät eingeschaltet und aktiv (nicht in Bereitschaft) ist.
RÜCKANSICHT 3. LINE IN: Eingang für vorverstärktes Mono-Audiosignal Ein Anschluss dieses Eingangs wird mit dem Ausgangsanschluss des Vorverstärkers für den gewünschten Kanal verbunden. Zum Beispiel „PRE OUT R“, wenn der SP-998 für den Lautsprecher des rechten Stereo-Kanals verwendet werden soll. Es kann immer nur einer der beiden Anschlüsse des Eingangs verwendet werden, der Umschalter „XLR/RCA“ muss sich in der richtigen Position befinden. Keine Hochpegelquelle anschließen! 3 4.
INSTALLATION Stellen Sie die Kabelverbindung in der nachfolgend genannten Reihenfolge her. Bringen Sie erst zuletzt das Netzkabel an und verbinden es mit der Steckdose. ZUR BESONDEREN BEACHTUNG Entfernen der Schutzkappen Vor der ersten Installation müssen von allen verwendeten Anschlüssen an der Geräterückseite die Kunststoff-Schutzkappen entfernt werden.
ANSCHLUSS EINES VORVERSTÄRKERKANALS Dieser Endverstärker ist mit einem Audio-Eingang („LINE IN“) versehen, an welchem das Gerät das vorverstärkte Signal eines Audio-Kanals (R, L, CENTER o.ä.) erwartet. Dies ist die Audio-Information, welche der SP-998 für den Lautsprecher aufbereitet. Hinweis: An diesen Eingang darf keine Quelle mit Standard-Hochpegelsignal („LINE OUT“) angeschlossen werden. Er ist nur für vorverstärkte Signale (z.B. „PRE OUT“) vorgesehen.
KABELVERBINDUNGEN FÜR DIE EINSCHALTSTEUERUNG (POWER CONTROL) Viele AV-Systeme bestehen aus einer Vielzahl von Einzelkomponenten. Um diese nicht vor und nach jedem Gebrauch alle einzeln aus- und einzuschalten, haben manche Hersteller die Geräte mit einer so genannten „TRIGGER“-Schaltung, auch „POWER CONTROL“ oder „Einschaltsteuerung“ genannt, ausgestattet. Vor allem für Vor- und Endstufen wird diese Art der ferngesteuerten Standby-Schaltung verwendet.
ANSCHLUSS DER LAUTSPRECHER An den Endverstärker SP-998 kann ein Lautsprecher normal (durch ein zweiadriges Lautsprecherkabel) angeschlossen werden. Es besteht aber auch die Möglichkeit, zwei Lautsprecher oder einen Lautsprecher im BiWiring anzuschließen. Für jeden Lautsprecher finden Sie am Gerät vier Lautsprecherklemmen (2x positiv + und 2x negativ -), von denen jeweils ein Paar mit einer Seite eines zweiadrigen Lautsprecherkabels verbunden wird.
ANSCHLUSS DER LAUTSPRECHER Wenn ein Lautsprecher im „Bi-Wiring“ angeschlossen werden soll, können beide LautsprecherKlemmenpaare verwendet werden. Anders als beim Anschluss der Lautsprecher mit je einem Lautsprecherkabel wird bei Bi-Wiring der dafür geeignete Lautsprecher über zwei getrennte zweiadrige Lautsprecherkabel oder ein vieradriges Lautsprecherkabel an das Ausgangsklemmenpaar des Endverstärkers angeschlossen.
ANSCHLUSS DER LAUTSPRECHER Wenn an das Lautsprecherkabel keine Steckverbinder angebracht werden sollen, entfernen Sie ein ca. 1 cm langes Stück der Isolierung von jedem Endstück des Lautsprecherdrahtes. Verdrillen Sie die blanke Litze, um Kurzschlüsse zu vermeiden. Drehen Sie den Knopf der Lautsprecherklemme im Gegenuhrzeigersinn, um ihn zu lösen und führen Sie das blanke Drahtende in das nun freiliegende Klemmenloch ein.
BEDIENUNG DES GERÄTES Aktion Ein- und Ausschalten Eingangsanschluss (XLR oder Cinch) wählen Taste(n) Beschreibung POWER (1) Das Gerät wird an der Gerätevorderseite ein- und ausgeschaltet. Die LED (2) an der Gerätevorderseite blinkt für fünf Sekunden nach dem Einschalten. Dies ist die Zeit in welcher eine Schutzschaltung aktiv ist und der Endverstärker stummgeschaltet ist. Die LED leuchtet danach dauerhaft, solange das Gerät aktiv ist.
WEITERE TIPPS Einspielzeit / Aufwärmen Ihre Audio-Geräte benötigen eine gewisse Zeit bis sie ihre klangliche Höchstleistung erreichen. Dieser Zeitraum ist für die verschiedenen Komponenten Ihres Systems sehr unterschiedlich. Bessere und gleichförmigere Leistung erhalten Sie während der Zeit, die das Gerät eingeschaltet bleibt.
FEHLERSUCHE Symptom Mögliche Fehlerursache Abhilfe Keine Funktion nachdem der Schalter „POWER“ in die Einschaltposition gebracht wurde Netzkabel nicht an eine betriebsbereite Steckdose angeschlossen. Stellen Sie eine Verbindung zu einer funktionierenden Steckdose mit der geeigneten Netzspannung her. Netzkabel nicht fest in die Steckdose und die Gerätebuchse gesteckt oder defekt.
FEHLERSUCHE Symptom Mögliche Fehlerursache Abhilfe Schlechte Tonqualität Anschlüsse der Kabelverbindungen sind lose, die Anschlüsse verschmutzt oder ein Kabel defekt. Prüfen Sie die Audio-Anschlüsse. Ein Plattenspieler wurde ohne zwischengeschaltete Entzerrervorstufe (Phonovorstufe) an einen der Hochpegeleingänge des Vorverstärkers angeschlossen. Schließen Sie eine Phonovorstufe an. Ein Gerät mit Hochpegelausgang (z.B. CDPlayer) wurde an den Endstufeneingang „LINE IN“ (3) angeschlossen.
LEXIKON/WISSENSWERTES Eingangsempfindlichkeit Begriff für die kleinste Eingangsspannung, die bei maximaler Lautstärkeeinstellung des Verstärkers die maximale Ausgangsleistung bewirkt. Beispiele: 100 mV bis 500 mV (Millivolt) bei Hochpegeleingängen, 2 mV bis 5 mV am Phono-MM-Eingang oder 0,1 mV bis 0,5 mV am Phono-MC-Eingang. Pegel Eine Art der Darstellung jeder physikalischen Größe und ein gebräuchliches Maß für Signalspannungen und Lautstärke. Wird in Dezibel (dB) angegeben.
SAFETY GUIDELINES This appliance was produced under strict quality controls. It complies with all established international safety standards. Nonetheless, the following instructions should be fully read and observed in order to prevent any hazard: Do not open the appliance! Risk of electric shock! There are no parts in the appliance that require maintenance by the user.
OTHER INSTRUCTIONS Setting up the appliance How the system is set up has an effect on the sound quality. Therefore only place it on a suitable, stable surface. To make the most of your system’s sound quality, we recommend placing the equipment on Vincent racks and not putting them on top of each other. Old electronic equipment This appliance is subject to the conditions set out in the European Directive 2002/96/EC. This is identified by the symbol of a crossed out waste bin on the appliance.
INCLUDED IN DELIVERY Please check the contents of the packaging, which in addition to the appliance should contain the following accessories: • 1 power cable • 1 cable for the POWER CONTROL • this manual DESCRIPTION OF THE APPLIANCE Vincent developers are not only dedicated to the stereo tradition but also create outstanding multichannel system audio and home cinema components. The reason we have spent much effort in main amplifier conception is that these devices can be used again in future audio systems.
FRONT VIEW 2 1. POWER: mains switch This button turns the unit on and into standby mode. When the SP-998 is switched off, the on/off signal at the input “POWER CONTROL” determines if the main amplifier is switched on or in standby mode. 2. POWER indicator LED This LED is lit as long as the device is active (switched on or activated via POWER CONTROL).
REAR VIEW 3. LINE IN: Input for preamplified mono audio signal One connector of this input must be connected with the output connector of the preamplifier for the desired channel. For example, connected with “PRE OUT R”, if the SP-998 is to be used for the loudspeaker of the right-hand stereo channel. Only one of the two input connectors can be used at any time. The setting “XLR/RCA” must be chosen correctly. Do not connect any line level sources! 4.
INSTALLATION Set up the cable links in a sequence as follows. Connect the power cable between device and power supply only after all other connections have been made. DURING INSTALLATION PLEASE OBSERVE THE FOLLOWING ADVICE: Protective caps Prior to the first installation the protective plastic caps must be removed from all the connections used at the rear of the unit.
CONNECTING THE PREAMPLIFIER This main amplifier is equipped with a mono audio input “LINE IN” (3) on which the unit awaits the preamplified signal of an audio channel (for example “PRE OUT R” or “FRONT R”). This is the audio information that the SP-998 provides for the loudspeaker. Please note: No source with a standard line level signal (“LINE OUT”) must be connected to this input. It is only intended for preamplified signals (e.g. “PRE OUT”).
CONNECTIONS FOR THE STANDBY CONTROL (POWER CONTROL) Many AV-Systems consist of a multitude of individual components. To avoid the necessity of switching them on and off before and after every use, many manufacturers have equipped their devices with what is known as “POWER CONTROL” circuit or “TRIGGER”. This kind of remote-controlled standby circuit is used primarily for preamplifier and main amplifiers, as power amplifiers are often placed far from other devices near the speakers.
CONNECTION OF THE LOUDSPEAKERS You can connect one loudspeaker the usual way (via a two-core speaker cable) to the power amplifier SP998. Some music enthusiasts may want to connect the speaker in “bi-wiring”. For each speaker the unit provides two speaker terminals (2x positive + and 2x negative –). One end of a conventional loudspeaker cable must be connected to one pair of those. Both terminal pairs (the two upper connectors and the two lower connectors) are parallel and receive the same mono signal.
CONNECTION OF THE LOUDSPEAKERS If one loudspeaker is to be connected with “bi-wiring”, both pairs of loudspeaker clamps may be used at the same time. In contrast to connection of the loudspeakers with one loudspeaker cable each, with biwiring a suitable loudspeaker is connected via two separate two-wire loudspeaker cables or one four-wire loudspeaker cable to the pair of output clamps on the main amplifier.
CONNECTION OF THE LOUDSPEAKERS If no connector is to be used, remove approximately 1 cm length of insulation from each end of the speaker wire. Twist the braid in order to avoid short circuits. Turn the fastener on the loudspeaker terminal counterclockwise to loosen it and introduce the bare wire end into the exposed connector hole. Then turn the fastener clockwise so that the wire is firmly clamped. Make sure the connection is pretty tight.
OPERATING THE APPLIANCE Operation Switch on and off Select the input connector Button(s) Description POWER (1) The amplifier is switched on and off using this button at the front panel. After switching on, the LED (2) located at the front panel flashes for about five seconds while the preamplifier’s protective circuit is active and muting the output. The LED is lit permanently as long as the amplifier is active.
TIPS Burn in/ Warm up Your audio components need a certain time period until they reach maximum performance. The duration of this “warm up” time is very different for the various elements of your audio system. Higher and homogeneous sound quality is achieved while keeping the device switched on. Your audio specialist dealer has enough experience to give you more information.
SEARCH FOR ERRORS Symptom Possible Cause Countermeasure Unit does not work after pressing the power button Mains cable is not connected to a suitable mains wall outlet. Connect to a functioning socket using a suitable mains voltage. Mains cable has not been firmly inserted into wall power socket and the device’s socket (7). Otherwise it may be defective. Check the power cable.
SEARCH FOR ERRORS Symptom Possible Cause Countermeasure Poor sound quality The cable connections are not tight, the connectors are dirty or a cable is defective. Check the cables and cable connections. A record player has been connected to a line level input of the preamplifier without using a phono preamplifier. Interconnect a phono preamplifier. An audio source with standard line level output (example: CD player) is connected to the power amplifier direct input “LINE IN” (3).
GLOSSARY Input sensitivity Term for the smallest average (RMS) input voltage which causes the maximum output power at the maximum volume setting on the amplifier. Examples: 100 mV to 500 mV (Millivolts) on high level inputs, 2 mV to 5 mV on the phono MM input or 0.1 mV to 0.5 mV on the phono MC input. dB level This is a way of describing any physical quantity; it is a common measurement for signal voltages and the volume. It is given in decibels (dB).
CONSIGNES DE SECURITE La construction de cet appareil a été soumise à des contrôles de qualité très stricts. Il répond à toutes les normes internationales de sécurité. Il est cependant nécessaire de lire entièrement les consignes suivantes et de les appliquer pour éviter tout danger : Ne pas ouvrir l'appareil! Danger de décharge électrique! Aucune pièce à entretenir par l'utilisateur ne se trouve dans l'appareil.
AUTRES CONSIGNES Montage de l'appareil Le site de montage de l'appareil a une incidence sur le son. Posez l'appareil uniquement sur une surface appropriée et stable. Pour profiter pleinement du potentiel sonore de votre système, nous vous recommandons de placer les appareils sur des racks Vincent et de ne pas les poser l'un sur l'autre. Appareils électroniques usagés Cet appareil est soumis aux dispositions fixées dans la directive européenne 2002/96/ CE.
CONTENU DE LA LIVRAISON Veuillez contrôler le contenu de l'emballage. Les accessoires suivants doivent être joints à l'appareil : • 1 câble de distribution • 1 câble avec fiches Jack 3,5 mm • le présent manuel DESCRIPTION DE L'APPAREIL Les concepteurs Vincent ont des obligations non seulement par rapport à la tradition stéréo, mais aussi pour les équipements Multicanal, dans un contexte où des cinémas à domicile et des composants de qualité supérieure et durables sont conçus.
FACADE AVANT 2 1. POWER : Interrupteur du secteur Ce bouton permet de démarrer l’appareil et de le mettre en état de fonctionnement. En position ARRET, l’appareil n’est pas coupé du secteur et réagit à la commande de commutation (POWER CONTROL). 2. VOYANT LED Ce voyant s’allume tant que l'appareil est allumé et en marche (pas en cours de démarrage).
FACADE ARRIERE 3. LINE IN : Entrée signal préamplifié mono-audio L’un des deux raccords de cette entrée doit être connecté au raccord de sortie du préamplificateur du canal souhaité. Par exemple avec « PRE OUT R », lorsque le SP-998 doit être utilisé pour le haut-parleur du canal stéréo situé à droite. Vous pouvez seulement utiliser l’un des deux raccords d’entrée, le commutateur « XLR/RCA » (3) sur la partie avant de l’appareil doit être convenablement réglé.
INSTALLATION Réalisez les raccordements des câbles dans l’ordre suivant. Raccordez le cordon secteur en dernier, et reliez-le à une prise secteur. VEUILLEZ TENIR COMPTE DES INSTRUCTIONS SUIVANTES LORS DE L’INSTALLATION : Dépose du capot de protection Avant la première installation, retirez les capuchons de protection des connecteurs à utiliser, situés sur la façade arrière de l’appareil. 1 2 les deux appareils sont de fabrication Vincent.
RACCORD D’UN CANAL DU PREAMPLIFICATEUR Cet amplificateur est équipé d’une entrée audio (« LINE IN ») (3), par laquelle l’appareil reçoit le signal préamplifié d’un canal audio (R, L, CENTER ou pareille). C’est le signal d’information musicale que le SP-998 traite pour le haut-parleur. Attention : Aucune source avec signal standard (« LINE OUT ») ne doit être connectée sur cette sortie. Elle est exclusivement réservée aux signaux préamplifiés (« PRE OUT »).
LIAISONS CABLEES POUR LA COMMANDE DE MISE SOUS TENSION (POWER CONTROL) De nombreux systèmes AV se composent de nombreux composants individuels. Pour éviter de les mettre en marche et de les arrêter l’un après l’autre à chaque utilisation, certains fabricants ont équipé les appareils avec un circuit appelé « Power Control », ou aussi « Trigger » ou encore « Commande de mise sous tension ». Ce type de télécommande Standby est avant tout utilisé pour les préamplificateurs et les amplificateurs.
BRANCHEMENT DES HAUT-PARLEURS Vous avez la possibilité de brancher normalement (avec un câble de haut-parleur à deux voies) un haut-parleur à un amplificateur SP-998. Pour cela vous trouverez sur l’appareil deux paires de bornes de serrage (positive + et négative -). Vous pouvez raccorder une extrémité d’un câble de haut-parleur à une paire de bornes de serrage. Les deux paires de serrage (les deux raccords supérieurs et les deux raccords inférieurs) émettent le même signal mono.
BRANCHEMENT DES HAUT-PARLEURS Si un haut-parleur doit être raccordé en « Bi-Wiring », on peut utiliser les deux paires de bornes de serrage « SPEAKER ». A la différence d’un raccordement de haut-parleur à l’aide d’un câble de hautparleur, en Bi-Wiring le haut-parleur en question est raccordé par deux câbles deux-conducteurs séparés ou un câble de haut-parleur quatre-conducteurs, à la paire de bornes de serrage de l’amplificateur de puissance.
BRANCHEMENT DES HAUT-PARLEURS En l’absence de cosse, retirez l’isolant de chaque extrémité du câble sur une longueur d’un cm environ. Torsadez le câble dénudé, pour éviter les court-circuits, desserrez la molette de fixation en la tournant dans le sens antihoraire et insérez l’extrémité du câble dans le perçage dégagé du bornier. Serrez maintenant le câble en faisant tourner la molette de serrage dans le sens horaire. Contrôlez le serrage correct du câble.
UTILISATION DE L’APPAREIL Action Touche(s) Mise en marche et arrêt POWER (1) Choisir un raccord d'entrée (XLR ou RCA) XLR/RCA (3) Description La mise en marche et l’arrêt de l’appareil se fait en façade avant. Une fois que l’appareil a été allumé, le voyant LED à la partie avant clignote pendant cinq secondes. Il s’agit de l’intervalle pendant lequel un disjoncteur est actif et l’amplificateur est allumé en mode muet.
CONSEILS Temps de rodage / échauffement Vos appareils audio demandent un certain temps pour atteindre leurs performances maximales. Ce laps de temps est très différent pour les différents composants de votre système. Vous obtiendrez un son de meilleure qualité et plus homogène en laissant l’appareil sous tension. Profitez de l’expérience de votre revendeur! Ronflement du secteur Certaines sources audio peuvent provoquer, en liaison avec l’amplificateur, un ronflement perceptible dans les haut-parleurs.
RESOLUTION DE PROBLEMES Symptom Cause possible du défaut Remède Pas de fonctionnement après mise en marche du commutateur secteur Le cordon secteur n’est pas relié à une prise opérationnelle. Réalisez une liaison à une prise opérationnelle avec la tension appropriée. Le cordon secteur est défectueux ou il n’est pas entièrement enfoncé dans la prise secteur ou celle de l’appareil.
RESOLUTION DE PROBLEMES Symptom Cause possible du défaut Remède Mauvaise qualité du son Les connexions des liaisons par câble sont desserrées, les connexions encrassées ou un câble est défectueux. Vérifiez les connexions audio et les câbles. Une platine tourne disque a été raccordée sans l’intermédiaire d’un préamplificateur phono à l’une des entrées de haut niveau du préamplificateur. Raccordez un préamplificateur phono entre la platine tourne disque et le préamplificateur.
GLOSSAIRE Niveau (dB) Une manière de représenter toute grandeur physique; mesure usuelle des tensions de signal et du volume. Est indiqué en décibels (dB). On désigne par tensions « au niveau Line » les tensions de signal inférieures à 1 Volt (RMS) qui conviennent comme signaux audio pour les entrées des amplificateurs. Les entrées de l’amplificateur (se présentant en général sous la forme de prises RCA) qui sont prévues pour les signaux du lecteur de CD, du lecteur de DVD etc.
Vincent Bewahren Sie die Kaufquittung zusammen mit der Bedienungsanleitung auf. Die Kaufquittung dient Ihnen als Nachweis für den Beginn der Garantiezeit. Die Seriennummer befindet sich an der Rückseite des Gerätes. Please keep the receipt, store it together with this manual. The receipt is your proof for the beginning of the warranty period. Note the serial number in the following box, you can read it from the rear side of the device. Gardez soigneusement la facture d'achat et le mode d'emploi.