Quick User Guide Table of Contents 1. Camera ................................................................................................................................. 1 1.1 Camera Features .......................................................................................................... 1 1.2 Device Initialization ...................................................................................................... 1 1.3 Modify IP Address ....................................................
1.Camera 1.1 Camera Features: 4MP/6MP POE IP camera dome/bullet, night vision, smart detection, built-in Mic optional, SD storage optional, motorized VF lens optional, 4X/5X zoom optional Plug and Play with Dahua POE NVR, can also work with ONVIF, easy access to third-party NVR and video surveillance system Management Software: Smart PSS, GDMSS,IDMSS, Easy4ip ,also easy setup in Blue Iris and VLC.
Figure 1-1 Figure 1-2 Figure 1-3 -2-
Figure 1-4 Figure 1-5 Step2:Initialize Camera Connect the camera to the LAN (local area network) > Open the the ConfigTool to search for the devices that need to be initialized > Select the device and Click the “initialize” > Enter your new password and confirm the password you have entered > Enter a email address to reset the password in case you forget the initial password you have set > Click the“Next”> Click the “ OK ” ,then the camera start being been initialized> Wait a few seconds to complete the in
Figure 1-6 Figure 1-7 -4-
Figure 1-8 Figure 1-9 -5-
Figure 1-10 Note: The following 2 lines of red warnings show the same IP conflict in the same LAN, you have to modify different IP addresses for the same IP devices .
1.3 Modify IP Address Steps: Select the devices that the IP need to be modified > Select the “Search Setting” and enter the camera's user name and password > Click “Modify IP “ or > Select the “Static”, and enter the start IP, subnet mask and gateway according to your LAN > Click “OK” to complete the IP modification. (See Figure 1-12) Note: You can set the DHCP mode if the local network can support the DHCP service, the device will automatically be assigned a IP address from the DHCP server.
Figure 1-13 Figure 1-14 Figure 1-15 -8-
2.Camera Setup < Conditions > Select “Setup” > “Camera” > “Conditions” > ,the system will display the settings for the camera conditions. (See Figure 2-1) Figure 2-1 < Zoom and Focus > Note: Only motorized vari-focal devices support focus and zoom function, like IPC-HDBW4431R-ZS, IPC-HFW4431R-Z , IPC-HDBW4631R-ZS, IPC-HFW4631H-ZSA ) Select “Setup” > “Camera” > “Conditions” > “Zoom and Focus” ,the system will display the zoom and focus settings.
Figure 2-2 < Video > Select “Setup” > “Camera” > “Video” , the system will display the video setting interface.
< Motion Detection > Select “Setup” >“Event” > “Video Detection” >“Motion Detection”>“Area Setup”, the system will display the “Motion Detection” setting interface. ( Firstly select the “ Enable” to enable the motion detection function). (See Figure 2-4 - Figure 2-5) Figure 2-4 Figure 2-5 Note: 1. Different colors stand for different areas; can set different colors for different detection area. 2.
triggering motion detection. < Smart Plan > Select “Setup” >“Event” > “Smart Plan” ,the system will display the “Smart Plan” setting interface. ( Firstly enable the smart plan before making the settings for IVS,Face Detection and other smart functions). ( See Figure 2-6 ) Figure 2-6 < IVS > Select “Setup” >“Event” > “IVS”, the system will display the “IVS” setting interface. Click “ set rule name and select the rule type.
Figure 2-7 3.Connect cameras to NVR 3.1.System Topology (reference only) 3.1.
3.1.2 NVR with POE ( See Figure 3-2 ) Figure 3-2 The camera can work with Dahua POE NVR,Plug and Play, besides,the IP camera also supports standard ONVIF protocol ,which can be added to third-party video recorder easily with ONVIF. Note: ① Before connecting cameras to NVR that has POE switch ,make sure the NVR and cameras have valid IP scheme that matchs each other.( e.g.: Hikvison NVR POE Port’s IP Network Segment is 192.168.25.XX, so the camera IP must be 192.168.25.
Steps2: The camera will automatically match the IP address of the NVR’s POE switch , refresh few seconds, video is showing, adding camera successfully. IP address of NVR‘s POE SWITCH : 10.1.1.1 .
Figure 3-5 3.2.2 Dahua NVR (WITHOUT POE) Configuration, adding camera manually Steps1: Connect cameras to POE switch or router ‘s Ports ,and then connect monitor and NVR via VGA or HDMI ports, power for those devices .Confirm the the LAN is available, and make sure the NVR , cameras and the POE switch router have valid IP scheme that matchs each other.( e.g.: POE switch router router’s IP is 192.168.1.1, so the camera and NVR’s IP must be 192.168.1.XX ).
Figure 3-6 Figure 3-7 Figure 3-8 - 17 -
Figure 3-9 Figure 3-10 - 18 -
You can also login in the IE Web interface of the NVR to add the camera manually. (See Figure 3-11) Figure 3-11 < Dahua NVR Web Adding Interface > 3.3 NVR Configuration with ONVIF (Take Hikvision NVR as an example) 3.3.1 Camera connect to Hikvison POE NVR (NVR have POE Ports) Note: 1.Make sure the POE switch’s IP address of the NVR and cameras have valid IP scheme that matchs each other 2. Enable the “ONVIF” of the camera and NVR in Web interface. Step1: Search for the NVR’s internal NIC IPv4 address.
showing,adding camera successfully.
Figure 3-14 Figure 3-15 - 21 -
Figure 3-16 Figure 3-17 - 22 -
You can also login in the IE Web interface of the NVR to add the camera manually. Figure 3-18 ) ( See Figure 3-18 3.3.2 Camera connect to Hikvison NVR via Router or POE Switch (NVR havn’t POE Ports) Note: 1.Make sure the NVR and cameras ’IP address have valid IP scheme that matchs each other 2.
< SADP for modifying NVR’s IP > Figure 3-20 Figure 3-21 - 24 -
Figure 3-22 Figure 3-23 - 25 -
You can also login in the IE Web interface of the NVR to add the camera manually (See Figure 3-24) Figure 3-24 < Hikvision NVR Web Adding Interface > 4. Mobile Phone APP 4.1 Download and install APP You can directly scan the QR code below based on your smartphone system to download app for Android or IOS ( gDMSS Plus for Android , iDMSS Plus for IOS) , you can also go to the “Google Play” or “App Store” to download and install it. 4.
connected to network. Step2: Open the iDMSS Plus app > Click icon of the home page at the bottom > Click icon of the “devices” > Select the“ SN/Scan” adding mode( you can also select the“IP/Domain” adding mode ) > Scan the QR code of the SN or maually enter SN. (See Figure 4-1 - Figure 4-6) Step3: Select the device type of wired camera password ,then click the adding icon successfully.
Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 - 28 -
Note: you can use the ConfigTool or login in the IE web pages to find the SN of the camera.
Dear Customer Thank you for your recent purchase of our IP cameras. We hope you will be pleased with both the product and service you received. If not, please give our helpful customer service team an opportunity to improve your experience right away; our team members are more than happy to help. . Meanwhile, we also welcome you to post a Product Review so that others can benefit from your experience. As a growing business, we know how scarce time can be, so we especially appreciate your time and input.