HD IR Waterproof Network Camera Quick Start Guide HD IR Waterproof Eyeball Network Camera Quick Start Guide 1
HD IR Waterproof Network Camera Quick Start Guide Important Notice 1. Please don’t update the firmware as it is updated from Chinese version and don’t 2. This user manual is taking IPC-HDW4431C-A as an example, but applies to other models (IPC-HDBW4431R-S, IPC-HDBW4431R-AS, IPC-HDBW4431R-ZS, IPC-HFW4431RZ, IPC-HFW4431M-I2, IPC-HDW4433C-A, IPC-HDBW4433R-S(R-AS),(R-ZS)). Table of Contents 1. Network Configuration ..............................................................................................
HD IR Waterproof Network Camera Quick Start Guide 1. Network Configuration Note: Camera power is DC 12V or POE 803.2a.f In order to make the camera get access to the network smoothly, please plan the useable IP segment reasonably according to the actual network environment. 1.1 Modify IP Address IP address can be acquired and modified through quick configuration tool for the cameras which are accessed via wired network.
HD IR Waterproof Network Camera Quick Start Guide Open the ConfigTool. If the camera is connected correctly, it will show as Figure 1-1. Figure 1-1 Step 2: Click the icon , input the IP address, which must be the same network segment with your computer, to target IP as below. Input Subnet Mask and Gateway, and then click refer to Figure 1-2 for more details. Figure 1-2 After entrying all information correctly, you will get the dialogue box as Figure 1-3: 4 .
HD IR Waterproof Network Camera Quick Start Guide Figure 1-3 1.2 Login WEB Interface Note: Different devices may have different WEB interfaces, the figures below just for reference. Install WEB plug-in when you use WEB client for the first time, the exact operation steps are shown as follows: Step 1: Two ways can open web interface successfully 1): Based on above steps, click icon , then it will connect IE directly. Please refer to Figure1-4.
HD IR Waterproof Network Camera Quick Start Guide Step 2: Page turn to the login interface shown as below, input your user name and password. Default factory user name and passwords is admin ,( new model camera is uninitialized, Need to set a new password to initialize it) then click “login”. See Figure 1-5 for more details. Figure 1-5 Note: The system will display “Update Password” prompt box for your first login, users need to modify the password and save it properly. Write it down in case forget..
HD IR Waterproof Network Camera Quick Start Guide Step 3: After logining successful , you may see the interface shown as in Figure 1-7. Figure 1-7 Click on “Please click here to download and install the plug-in”. The system pops up a warning information siad “do you want to run or save this file? ”.
HD IR Waterproof Network Camera Quick Start Guide Click the “run” directly or save the file ,then install it. Follow the following steps,see Figure 19 and Figure 1-10.
HD IR Waterproof Network Camera Quick Start Guide When plug-in installation is completed, the page will close directly followed by the web-end refreshment, then video captured will be shown. Conditions Conditions: Adjust image quality--see Figure 1-11.
HD IR Waterproof Network Camera Quick Start Guide Click “Refresh” ,device will automatically synchronize the hardware to the location of sliding block of lens zoom and focus. Figure 1-12 Video Set the Camera Parameters: Select “Setup > Camera > Video > ” and the system will display the interface of “Video”.
HD IR Waterproof Network Camera Quick Start Guide SMTP (e-mail) The SMTP interface --See Figure 1-14 Figure 1-14 Motion Detection Select “Setup > Event > Video Detection > Motion Detection” and the system will display the interface of “Motion Detection” -- see Figure 1-15 and Figure 1-16 Figure 1-15 Select “ Area setup” to set the motion detection area --see Figure 1-16 Figure 1-16 11
HD IR Waterproof Network Camera Quick Start Guide IVS IVS included some events. --see Figure 1-17 Figure 1-17 2. Connect to NVR There are two ways that connect to NVR (two types of NVR), shown in Figure 2-1 Figure 2-1 NVR: Connect camera to NVR, the NVR will auto adjust to camera IP, don’t need modify camera IP. ONVIF NVR (Third-party brand) 1) Camera connect to NVR that have POE Ports, the camera IP Network Segment must be same as the NVR Port’s. (e.g.: Hikvison NVR Port’s IP Network Segment is 192.
HD IR Waterproof Network Camera Quick Start Guide 2) Camera connect to NVR via POE switch or router (NVR have not POE ports), the camera IP Network Segment Should be same as the POE switch or router’s. (e.g.: router’s IP is 192.168.1.1, so the camera IP must be 192.168.1.XX). 2.1 NVR Configuration Search the IP by the Configtool. If your NVR is uninitialized, you need to initialize the device. Login the NVR via browser, install the plugins. 2.1.
HD IR Waterproof Network Camera Quick Start Guide Figure 2-3 Figure 2-4 2.2 ONVIF NVR Configuration (Hikvison NVR for example) 2.2.1 camera connect to Hikvison NVR POE Ports.(NVR have POE Ports) Note: Check your NVR preview and playback max resolution supported before configuration. Step1:Log in the camera via browser. Adjust camera resolution is higher than NVR max preview resolution, and Synchronize Time in accordance with your local time.
HD IR Waterproof Network Camera Quick Start Guide Figure 2-6 Step2: Hikvison NVR POE Ports’s IP Segment is 192.168.254.XX, Change camera IP to 192.168.254.XX, shown in Figure 2-7, then connect camera to NVR port.
HD IR Waterproof Network Camera Quick Start Guide Click camera channel , then click “modify”, adding method select “manual”, enter camera IP, protocol select “ ONVIF”, Port “80”, enter the camera password, click “OK”. Shown in Figure 2-9 Figure 2-9 Refresh several times, status will be online, connected successful. Shown in Figure 2-10. Figure 2-10 2.2.
HD IR Waterproof Network Camera Quick Start Guide Figure 2-11 Click the camera channel , then click “Quick Add”, select the camera, click “ok”, then click “modify”, enter the camera IP, Protocol select “ ONVIF”, Port is “80”, enter the camera password, click “OK”. Shown in Figure 2-12, Figure 2-13 Figure 2-12 Figure 2-13 Refresh several times, it will be online status, connected successful.
HD IR Waterproof Network Camera Quick Start Guide Figure 2-14 3. Mobile Phone APP 3.1 Downloading and Installation The product has Android and iOS versions Android: Open Google Play app in your smart phone. In Google Play, search gDMSS Plus. The first app searched out should be this software. See Figure 3- 1. Figure 3- 1 iOS: Open App Store APP in smart phone. search iDMSS Plus. The first app searched out should be this software. See Figure 3- 2.
HD IR Waterproof Network Camera Quick Start Guide 3.2 Add Device Open the APP, touch Device Manager icon to manage devices, shown in Figure 3- 3 Select the P2P ,DDNS, IP/Domain to add the device, If you select the P2P, you can Scan QR Code to add device, the QR Code is on the camera boday.
HD IR Waterproof Network Camera Quick Start Guide Figure 3-4 Figure 3- 5 Anymore Questions Met, pls contact our technician: Bill E-mail:support@vikylin.