Installation Manual

1
Connecting the camera to system
2
Modifying the camera’s IP address
2
Modifying the camera’s IP address
3
Using Device SearchTool
4
Working with Internet Explorer
HD IP CAMERA
Quick Start Guide
Figure 1: Working With POE NVR
Default: IP address: 192.168.1.110 , Username: admin, Password: 123456
( We strongly recomm end modifying the default password for your security).
Each IP camera has the same default IP address after leaving the factory. In order to
guarantee network connectivity and access the live video, it is essential to change the
camera’s IP address to unique via computer before using. You can install the device
search tool AjDevTools and Hikvision SADP tool
https://drive.google.com/file/d/1lJ1fOLKizOIN2gyiF1ikPV9niAySxf9K/view?usp=sharing
Before modifying the IP address you’d better confirm the IP network planning and avoid
IP address conflict.
Steps on Local Area Windows 10 PC : Search Windows -> cmd -> ipconfig /all
Right-click on the Network icon and select open Network and Sharing Center.
Toaccess the camera’s web interface, type in the IP camera’s IP address in Internet
Explorer’s URL bar to gain access to the login page. Please modify IP address to the
same subnet if login page can not load.
(Default user name: admin, Password: 123456) Firefox ESR and IE are supported.
Note:
V 2021.01
RJ-45
To PoE Switch LAN port
To Switch or Router LAN port
HD IP Camera (PoE)
DC 12V
To router LAN port
PoE
Swit ch
RJ-45
Router
POE Ethernet Switch
HD IP Camera
(without PoE)
To Switch or Router LAN port
Power Adapter
HDMI or VGA output
Figure 2: Working With POE Switch
Note:
1. The camera should be connected to an OPTIONAL 12 volt power supply if you do not use PoE (Power
over Ethernet).
2. A Windows computer is more convenient to setup and troubleshooting.
Note
：
you can also find out the LAN configuration via Windows GUI
If the camera is installed to work with the local switch or router directly, the camera
IP range should be 192.168.1.x (x=2-254). To void IP conflict, you should test and
select an unoccupied IP like this:
Command Prompt ping test
Only when reply unreachable
that means the IP address is no
conflict and available, otherwise
when you see time reply do not
use this IP address.
a. Click Start Search and all your cameras in
the LAN will be listed. Modify IP address to suit
the LAN’s IP scheme. There are two modifying
methods available: 1) Right click on the desired
camera and choose “Modify IP address”. 2) Click
the ALL check-box then click “IP Batch Setting”.
b. You can also enable the camera DHCP function if
there is a DHCP server available in the LAN.
Most router has DHCP server built-in. (IP address in DHCP setting may change after
device restart. We do not recommend leaving the IP camera on DHCP).
Tips:
Reset Password -> Restore default settings;
Video full-screen -> double-click video;
From the login page, select your familiar language, then log in with the username
and password.
This manual may contain some incorrect places, even though it was published with our carefully proofreading.
The news updates will be added to the next release without notice. Your valuable advice is really appreciated.
Firmware upgrade -> Select the check-box, click Browse then click File Upgrade.
1
2
3
4
5
HDMI or VGA output
To NVR PoE port
HD IP Camera (PoE)
PoE NVR
RJ-45
To router LAN port
RJ-45
DC 12V
RJ-45 To router LAN port
HD IP Camera
(without PoE)
Now you can get all the
local network information.
IPv4 Address: 192.168.1.?
Subnet Mask: 255.255.255.0
Default gateway: 192.168.1.1
DNS Servers: 192.168.1.1