MODEL WIDTH BLOWER (purchased separately) VDDS300/CVDD5300 30° W. VDVI600 Interior or RESOLVED Exterior VDDS360/CVDDEIS0 36° W. ADVISED Interior or RESOLVED Exterior VDDB450/CVDDE4S0 45" W. WORLDVIEW Interior or EAVESDROP Exterior, VDVE1200 Exterior VDD5480/CVDDEAB0 48" W. YDVI&00 Interior or RESOLVED Exterior, VDVE1200 Exterior READ AND SAVE THESE INSTRUCTIONS WARNING £4 OH WARNING 4A A TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1.
CONTENTS PLAN THE DUCT WORK These parts are included with your downdraft housing: 1 Pants Bag containing: 2 2-in. Support Legs 2 4-in.
PLAN CABINET CUTOUTS PREPARE THE DOWNDRAFT — — CAUTION: i HOLE IN CABINET I | g-CABINET FOR DUCT WORK, check for interference with floor joists, wall studs, electrical wiring, or plumbing, & 2 lew 4 Mack 2 VIEW I SIDE INSTALLATION CENTER LINE INSIDE CABINET 14" a “HOLE FOR 8 or FLOOR 1 40" ROUND DUCT {"Adjustable 8’ Lat and &" Right} (When using Remote Discharge Plats Hole is adjustable 8° Loft ard 8° Right from installation Center Line } Liz the dimensions in the above illustration to help plan how and whe
COVER PLATE {included with discharge plate) ROUND REMOTE DISCHARGE PLATE (Purchase Separately} COVER PLATES {included with discharge plate} 2 Installations using FLEX BLOWER (in remote location) or REMOTE BLOWER only: 4. Use the REMOTE DISCHARGE PLATE and determine its location on FRONT PANEL. Use a combination of COVER PLATES (3” and/or 8” wide} to close the opening on side(s} of remote discharge plate. Sid the remote cover plate and cover plates between the LOWER CHANNEL and the clamp channel.
Las CI lea el NE mounted in a remote location only: &. Remove (8) #8-32 MEX NUTS and ELECTRICAL PANEL. 5-ft. extension cables {purchase separately) may ba needed to mount electrical pane! in a remote location. Do not use more that 2 extension cables, _ SCREWS Installations using FLEX BLOWER only: 7. Attach BLOWER SUPPORT LEGS with (4) SCREWS provided. Do not use legs alone for support. it may be necessary to add extra support for the flex blower.
CUT COUNTER TOP OPENING 1. Lay out and cut the cookie cut-out far enough FORWARD se downdraft will fit behind it. 2. Set cook top in place and slide it as far forward as possible without exposing an gaps. Center and square it with edges of counter top. 3. Extend SUPPORT LEGS and attach to bottom of cabins with {2} SCREWS through each leg. Tighten HEX SCREWS. ¥ cabinet bottom is removed: Use blocks as spacers between floor and support legs. Template against back edge of cook top.
INSTALL DUCT WORK CAUTION: BEFORE CUTTING HOLE IN CABINET FOR DUCT WORK, check for interference with floor joists, wall studs, electrical wiring, or plumbing. . Holstein cabinetmaking sinkhole wall or floor as necessary. . Counteroffer oral! cap and work back towards the cabinet, stitching ail duct work, slows and transitions as previously planned. Tape ail duct work connections to make them secure and air tight. . Connect duct work (and transition, if required} to downdraft. If necessary, usa (2) #8-18 x .
INSTALL FINISH TRIM CHIMNEY DOWNDRAFT HOUSING 1. Raise chimney and attach FINISH TRIM to top/left and top/ right of DOWNDRAFT HOUSING with screw provided. INSTALL COOKING APPLIANCE 1. Align the cooking appliance with downdraft and fasten appliance in place following appliance instructions. Note: Accurate alignment of cooking appliance and downdraft is necessary to ensure that thees is no interference when air vent ia raised and lowered.
OPERATION 4-Snead Fan Speed Control 2-Lee! Task Light 30-Hour Filter Clean Reminder 10 4-Spade Fan Speed Control Press + button to increase fan speed. Press button to decrease fan speed. After maximum speed is reached, press + button once more to turn off fan. 2-Level Task Light Press acne for LOW setting. Press 2x for HIGH setting. Leon will illuminate. Press 3x to tum task light OFF 30-Hour Filter Clean Reminder After 30 hours of blower "ON" time, filter Nisan icon will blink continuously.
USE AND CARE SERVICE INFORMATION WARNING: Always disconnect electric power supply before cleaning and/or servicing unit. é Always turn the downdraft blower on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clean the air after you turn the cook top off. This will esp the hols kitchen cleaner and brighter, Cleaning To clean grease filters: Remove front pane! and take out the {2) grease filters.
WARRANTY DOWNDRAFT WARRANTY ONE YEAR FULL WARRANTY Downdrafts and all of thee component parts, except as detailed baiow*!, sre warranted ta be free from defective materials or workmanship in normal residential use for 5 period of one {1} year from the date of original retail purchase. Viking Range, LLC, tormentor, agrees to repair of replace, st its caption, any part which fails or x found 0 be defective during the warranty period.