Installation Manual

ManualsBrandsViking ManualsIntercom SystemViking E-30

E. Timing/Dialing Options (Memory Location #18)

There are six positions in the timing/dialing options. To program these options, enter the six desired timing/dialing dig-

its followed by #18. The six available timing/dialing options are defined as shown below.

Dial:A+B+C+D+E+F+#+1+8

Factory Default Setting: 2 + 3 + 4 + 1 + 1 + 1

Talk/Listen Delay

Call Length

Silence Time Out

Dial Next Number on Ring No Answer

Dial Next Number on Busy

Pulse Dial Speed

Enter Timing/Dialing Settings Here:

A B C D E F

#18

Setting A - Talk/Listen Delay

This feature selects switching time between talk and listen modes

(VOX switching time). Use chart at the right. * Note: The factory

default is .2 seconds.

Setting B - Call Length Time Out

This feature selects the maximum length of time that calls can be connected. Programmable

in increments of 1 minute up to a maximum of 9 minutes (Touch Tones 1 - 9). Program 0 in

this location to disable the call length time out. With the call length disabled, the E-30 phone

must rely on CPC, busy, silence or return dialtone to hang-up. Use chart at the far right.

*Note: The factory default is 3 minutes.

Touch

Tone

Talk/Listen

Delay

.1 sec

.2 sec *

.3 sec

.4 sec

.5 sec

.6 sec

.7 sec

.8 sec

.9 sec

Touch

Tone

Call Length

Time Out

Disabled

1 min

2 min

3 min*

4 min

5 min

6 min

7 min

8 min

9 min

D. Speed Dial Numbers (Memory Locations #00 - #04)

Note: Up to 20 digits can be stored in each dial position. Special features such as pause, mode change, Touch Tone

and # count as single digits.

The speed dial number programmed in location #00 is the telephone or extension

number that is dialed when the “Call” button is first pressed. Additional speed dial

numbers will be dialed when there is no answer or a busy signal is detected and the

next number redial features are activated. The E-30 will cycle through the pro-

grammed speed dial numbers until answered. To program, enter the desired speed

dial number followed by the memory location number (#00 - #04).

To clear a speed dial location, simply enter the memory location (#00 - #04) alone.

The E-30 is factory set with no speed dial number programmed.

To Program:

4 second pause

switch to pulse mode

0, 1, 2...9

Enter:

0, 1, 2...9

B. Quick Programming Features

First speed dial number ...........................................................................................

Second speed dial number ......................................................................................

Third speed dial number ..........................................................................................

Fourth speed dial number ........................................................................................

Fifth speed dial number ...........................................................................................

To add a

, at any point in the dialing string ...............................................................

To add a # at any point in the dialing string ...............................................................

To add a four second pause at any point in the dialing string ....................................

Toggle between Touch Tone and Pulse dialing .........................................................

Timing/Dialing options (factory set to 23411) ...........................................................

Change security code (factory set to 845464) .........................................................

0-20 digits

6 digits (0-9)

#00

#01

#02

#03

#04

#18

#19

Enter Digits

then

- then -

Enter Memory Location

C. Security Code (memory location #19)

The security code allows the user/installer to program the E-30 phone while DIP switch 3 is in the ON (normal) posi-

tion. The factory set security code is 845464 (V-I-K-I-N-G). It is recommended that the factory set security code be

changed. Example: To store 123456 as the security code:

Enter Your Security Code Here:

#19

Step 1. Access programming as shown is Programming section A.

Step 2. Enter 123456 #19..

Step 3. Hang-up.

Note: The security code must be 6 digits and cannot include a

or a #.