ViewZ 5.6" HD-SDI CCTV TEST MONITOR 5.6" HD-SDI CCTV TEST MONITOR User’s Manual Please read this Manual carefully before use of this product, and keep it handy for future reference.
ViewZ 5.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR I. Packing List ……………………………………………….. 2 II. Product Appearance………………………………………... 3-5 III. Product Operation………………………………………….. 6-8 9-10 Contents IV. Screen Display……………………………………………... V. List of Supported Display Modes………………………….. 11 VI. Technical Parameters………………………………………. 12 VII. Troubleshooting………………………………………….
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Packing List 5.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR 2 3 4 5 6 Product Appearance 7 8 Front View 1 1 5.6 " LCD panel (adopting tempered glass cover). 2 LED indicator. 3 MEMU Key: The main menu key, acting as the Enter Key during menu operation. 4 SOURCE Key: With the function of signal channel switching, acting as the Left Selection Key during menu operation. 5 P/G Key: With the function of color bar signal output built in this device, acting as the Right Selection Key during menu operation.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR 1 2 6 3 7 Product Appearance 4 5 Rear View 1 Left Side View Video 2 signal input interface or SDI signal input interface (depending on the product model). 2 Audio signal input interface. 3 Video signal output and color bar signal output interface 4 DC12V --350MA output interface. 5 Power switch. The product can work properly only when the switch is turned “ON”. 6 VGA signal input interface. 7 HDMI signal input interface.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR 6 1 2 3 4 Product Appearance 5 Right Side View 1 Top View Picture brightness adjusting knob: turn it upwards to increase the brightness, and turn it downwards to decrease the brightness. 2 Picture contrast adjusting knob: turn it upwards to increase the contrast, and turn it downwards to decrease the contrast. 3 Picture saturation adjusting knob: turn it upwards to increase the saturation, and turn it downwards to decrease the saturation.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Step 1: As shown in Fig. 1, put four Ni-MH cells in the battery compartment of the product in sequence according to the anode and cathode marks. (Please pay attention to the anode and cathode of each battery; installation with reversed node and cathode may result in electrical failures and damage the Product Operation Step 2: Turn the power switch “ON”, the LED indicator stays on in green and the device is working properly.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Charge and Discharge Connect the DC12V-1500mA charger from the accessories according to the figure shown, and connect to the AC power. After the charger is inserted, the LED indicator (green-green-off) acts once; then, it enters the test state, and the LED indicator flashes fast (red-green-red-green…) for about 13 times; if the battery has no defects, it will enter the normal charging state.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR 1 2 3 Product Operation 4 3 Information Display on the Screen 1 Battery charging icon. 2 Display of the signal channel information and resolution of the current screen. 3 Display of battery level and indication of DC12V output state. 4 Display of the intensity of the current video signal input.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Signal Selection Menu Operation method: Press the “SOURCE” key, and the signal channel selection interface will appear on the screen as shown in the figure on the left. Press the “SOURCE” key again, and the yellow cursor will move down to the next signal channel; stay on this channel for about 1 second, and the screen will display the signal channel where this cursor stays.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Screen Display Main Menu (Settings) Operation method: Press the “MENU” key, and the main menu interface will appear on the screen as shown in the figure on the left. Press the “SOURCE” key and “P/G” key to select submenus leftwards and rightwards; press the “VSM” key to select submenus downwards in a cyclic way; press the “MENU” key again to confirm the current selected submenu. Press the “ESC” key to go back level by level and exit the menu.
ViewZ 5.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Product name Multifunction Monitor Product specification Technical Parameters LCD panel Signal interface Control mode Power supply Operating environment Other information 5.6" Display area 112.896 (H) ×84.672 (V) mm Display scale 4:3 Backlight LED Resolution 640×480 Brightness 200cd/㎡ Contrast ratio 500:1 Response time 10ms Dot matrix 0.0588 (H) ×0.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Before asking for maintenance, please check the information in this section to see if the problem can be solved by yourself; if necessary, please contact our After-sales Service Center or the distributor. Problem Possible cause The battery is used up. The battery is installed with its anode and cathode reversed. The AC charger is not properly Solution Recharge the battery or install a fully charged battery. Reinstall the battery correctly.
ViewZ 5.6" HD-SDI CCTV TEST MONITOR Problem Possible cause Solution The charging There is dirt on battery Clean the battery terminals with a piece of soft indicator indicates terminals. dry cloth. The battery has been charged The service life of the battery is expired; please for numerous times. purchase a new battery. normal charging, but the battery is not being charged There is no video signal input. Check if the front-end equipment generating video signals works normally.