® ViewSonic PJD5111 DLP Projector - User Guide - Guide de l’utilisateur - Bedienungsanleitung - Guía del usuario - Guida dell’utente - Guia do usuário - Användarhandbok - Käyttöopas Ɋɭɤɨɜɨɞɫɬɜɨ ɩɨɥɶɡɨɜɚɬɟɥɹ - ٺҢЙыġĩᖅᡝĪ IMPORTANT: Please read this User Guide to obtain important information on - ሢ၊࿁ġĩ⇷␅Ī installing and using your product in a safe manner, as well as registering your product for future service.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.
Copyright Information Copyright© ViewSonic® Corporation, 2009. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Table of contents Important safety instructions .......................2 Introduction......................5 Projector features ................................. 5 Shipping contents................................. 6 Projector exterior view......................... 7 Controls and functions ......................... 8 Positioning your projector..........................11 Choosing a location............................ 11 Projection dimensions ........................ 12 Connection ......................
Important safety instructions Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this unit near water. Clean with a soft, dry cloth. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other GHYLFHV LQFOXGLQJ DPSOL¿HUV WKDW SURGXFH KHDW 9.
19. In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. ,Q DUHDV ZKHUH WKH PDLQV YROWDJH PD\ ÀXFWXDWH or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS). 20.
30. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury. 31. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply’ s wall socket and call your local service center to have the projector serviced. 32.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features.
Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated. Projector Power Cord VGA Cable Multi-language user manual CD Quick Start Guide Remote Control & Battery Pull the tab before using the remote control. Optional accessories 1. 2. 3.
Projector exterior view Front/upper side 1. 1 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 2 5 3 6 4 7 12. Rear/lower side 8 9 10 11 12 13 14 15 16 17 21 18 19 13. 14. 15. 16. 17. 18. 19. 20. 21. 20 External control panel (See "Projector and remote control" on page 8 for details.
Controls and functions Projector and remote control 12 1 5 18 14 10 15 11 16 13 6 2 3 9 4 5 6 7 8 10 8 11 6 12 6 17 19 13 1. 2. 3. 4. 8 Focus ring Adjusts the focus of the projected image. See "Fine-tuning the image size and clarity" on page 25 for details. Zoom ring Adjusts the size of the image. See "Finetuning the image size and clarity" on page 25 for details. TEMPerature indicator light Lights up red if the projector's temperature becomes too high.
9. 10. 11. 12. 13. 14. LAMP indicator light Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem. See "Indicators" on page 46 for details. 15. AUTO Automatically determines the best picture timings for the displayed image. See "Auto-adjusting the image" on page 24 for 16. details. Right/ 17. Activates panel key lock. See "Locking control keys" on page 31 for details.
Remote control effective range Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (~ 26 feet). Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam. Appr ox.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of four possible installation locations: 1.
Projection dimensions Refer to "Dimensions" on page 49 for the center of lens dimensions of this projector before calculating the appropriate position. • 4:3 image on a 4:3 screen (a) (b) (e) (a) (f) (d) (c) (c) (d) (f) (e) • (b) 16:9 image on a 4:3 screen (b) (a) (a) (e) (f) (d) (c) (c) (d) (f) (b) (e) (e): Screen (f): Center of lens 4:3 Screen (a) Screen (b) Projection distance (c) Image (d) Vertical Size [m (inch)] height offset [inch (m)] [cm (inch)] [cm (inch)] min. max.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 6). They are commercially available from electronics stores.
Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused Component Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1. 2. 3. 4.
Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. 2. 3. 4. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.
Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. 2. 3. 4. Take a Video cable and connect one end to the composite Video output socket of the Video source device.
Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector flashes blue after power has been applied. 2. Remove the lens cap. If it is closed, it could become deformed due to the heat produced by the projection lamp. 3. Press II POWER on the projector or remote control to start the projector. The POWER indicator light stays blue when the projector is on.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. Below is the overview of the OSD menu. Main menu icon Screen Color Aspect Ratio Keystone Position Phase H. Size Digital Zoom Highlight Sub-menu Current input signal Off Auto Status ENTER 16 0 Analog RGB MENU Exit Press MENU/ EXIT to the previous page or to exit. To use the OSD menus, please set them to your familiar language first. 1.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 20. You will be inconvenienced if you activate the password functionality and subsequently forget the password.
Entering the password recall procedure 1. 2. 3. Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. RECALL PASSWORD Please write down the recall code, and contact ViewSonic Customer Center.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of this projector) if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1. 2. • Press SOURCE on the projector or remote control. A source selection bar displays.
Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. 2. Screw the rear adjuster foot to fine tune the horizontal angle.
Fine-tuning the image size and clarity 1. Adjust the projected image to the size that you need using the zoom ring. 2. Then sharpen the image by rotating the focus ring. Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps.
Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • Using the remote control 1. Press Digital Zoom +/- to display the Zoom bar. 2. Press Digital Zoom + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need. 3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 4.
About the aspect ratio In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio. 16:10 picture 15:9 picture 2. 3.
Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps. • • Press MODE/ENTER on the remote control or projector repeatedly until your desired mode is selected. Go to the PICTURE > Preset Mode menu and press / to select a desired mode.
Setting the User 1/User 2 mode There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/User 2) as a starting point and customize the settings. 1. 2. 3. 4. Press MENU/EXIT to open the On-Screen Display (OSD) menu. Go to the PICTURE > Preset Mode menu. Press / to select User 1 or User 2. Press to highlight Reference Mode.
Adjusting Color Highlight the PICTURE > Color menu and press / . Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic. Adjusting Tint Highlight the PICTURE > Tint menu and press / . The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes. Adjusting Sharpness Highlight the PICTURE > Sharpness menu and press / .
Hiding the image In order to draw the audience's full attention to the presenter, you can use on the projector or BLANK on the remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden.
Freezing the image Press FREEZE on the remote control to freeze the image. The word 'FREEZE' will display in the upper left corner of the screen. To release the function, press any key on the projector or remote control. Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected devices have active audio output, you will still hear the audio even though the image is frozen on screen.
Adjusting the sound level To adjust the sound level, press Volume +/- on the remote control, or: 1. 2. Repeat steps 1-2 above. Press to highlight Volume and press / to select a desired sound level. Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Main menu Sub-menu Screen Color 1. DISPLAY 2. PICTURE Aspect Ratio Keystone Position Phase H.
Language 4. SYSTEM SETUP: Basic Projector Position Front Table/Rear Table/Rear Ceiling/Front Ceiling Auto Power Off Disable/5 min/10 min/15 min/20 min/25 min/30 min Blank Timer Disable/5 min/10 min/15 min/20 min/25 min/30 min Panel Key Lock On/Off Timer Controller Disable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/12 hr Splash Screen Black/Blue/ViewSonic Quick Cooling On/Off High Altitude Mode On/Off DCR On/Off Active VGA Out On/Off Audio Settings 5.
Description of each menu Function (default setting/value) Description (default setting/value) Screen Color Corrects the projected picture’s color when the projection surface (Off) is not white. See "Using Screen Color" on page 29 for details. Aspect Ratio There are three options to set the image's aspect ratio depending on your input signal source. See "Selecting the aspect ratio" on page 26 for details. (Auto) Keystone 1. DISPLAY menu (0) Position (0) Phase Displays the position adjustment page.
Function (default setting/value) Tint (0) 2. PICTURE menu Sharpness (15) Brilliant Color (On) Description (default setting/value) Adjusts the red and green color tones of the image. See "Adjusting Tint" on page 30 for details. The function is only available when Video or S-Video with NTSC system is selected. Adjusts the image to make it look sharper or softer. See "Adjusting Sharpness" on page 30 for details. Adjusts white peaking while maintaining correct color presentation.
Function (default setting/value) 4. SYSTEM SETUP: Basic menu Timer Controller (Disable) Description (default setting/value) Sets the auto-shutdown timer. The timer can be set to a value between 30 minutes and 12 hours. Splash Screen Allows you to select which logo screen will display during projector start-up. Three options are available: ViewSonic logo, (ViewSonic logo) Black screen, or Blue screen.
Function Description (default setting/value) (default setting/value) Closed Caption Enable (Off) Activates the function by selecting On when the selected input signal carries closed captions. • 5. SYSTEM SETUP: Advanced menu Closed Caption Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings). Set your screen aspect ratio to 4:3.
Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust.
Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows: Total (equivalent) lamp hour = 1 (hours used in Economic mode) + 4/3 (hours used in Normal mode) See "Setting Lamp mode as Economic" below for more information on Economic mode. The lamp hour in Economic mode is calculated as 3/4 of that in Normal mode.
Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. CAUTION The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
Replacing the lamp To prepare a new lamp, contact your dealer and tell the lamp type number. Type number : RLC-047 WARNING Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
5. Pull out the lamp connector from a slot in the lamp compartment. Disconnect it from the projector as illustrated. 2 1 2 6. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. CAUTION • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.
9. Tighten the screw that secures the lamp. CAUTION • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 10. Ensure the handle is fully laid flat and locked in place. 11. Replace the lamp cover on the projector. 12. Tighten the screws that secure the lamp cover. CAUTION • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screws. 13. Restart the projector.
Indicators Light Power Temp Status & Description Lamp Power events Blue Flashing Off Off Stand-by mode Blue Off Off Blue Off Off Blue Flashing Off Off Powering up Normal operation 1. The projector needs 90 seconds to cool down as it was abnormally shut down without the normal cooling down process. Or 2. The projector needs to cool for 90 seconds after the power is turned off. Or 3. The projector has shut down automatically. If you try to re-start the projector, it will shut down again.
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications Projector specifications All specifications are subject to change without notice. General Product name Model name Digital Projector PJD5111 Optical Resolution Display system Lens F/Number Lamp 800 x 600 SVGA 1-CHIP DMD F = 2.56 to 2.8, f = 21 to 23 mm 185 W lamp Electrical Power supply Power consumption AC100–240V, 2.9 A, 50/60 Hz (Automatic) 280 W (Max) Mechanical Dimensions Weight 264 mm (W) x 96.4 mm (H) x 225 mm (D) 5.07 lbs (2.
Dimensions 264 mm (W) x 96.4 mm (H) x 225 mm (D) 225 264 96.4 60 66 Timing chart Supported timing for PC input Resolution 640 x 480 720 x 400 800 x 600 1024 x 768 1280 x 800 1280 x 1024 1280 x 960 640 x 480@67Hz 832 x 624@75Hz 1024 x 768@75Hz 1152 x 870@75Hz Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 31.469 37.861 37.500 43.269 31.469 37.879 48.077 46.875 53.674 48.363 56.476 60.023 68.667 49.702 63.981 60.000 35.000 49.722 60.241 68.680 59.940 72.809 75.
Supported timing for Component-YPbPr input Signal Format Horizontal Frequency (kHz) Vertical Frequency (Hz) 480i(525i)@60Hz 480p(525p)@60Hz 576i(625i)@50Hz 576p(625p)@50Hz 720p(750p)@60Hz 720p(750p)@50Hz 1080i(1125i)@60Hz 1080i(1125i)@50Hz 15.73 31.47 15.63 31.25 45.00 37.50 33.75 28.13 59.94 59.94 50.00 50.00 60.00 50.00 60.00 50.00 Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.
Copyright information Copyright Copyright 2009. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Appendix IR control table Key Format Byte1 Byte2 Byte3 Byte4 Power NEC 83 F4 02 fd Freeze NEC 83 F4 03 fc Up NEC 83 F4 0b f4 Down NEC 83 F4 0c f3 Left NEC 83 F4 0d f2 Right NEC 83 F4 0e f1 Mode NEC 83 F4 0f f0 Volume+ NEC 83 F4 05 fa Volume- NEC 83 F4 06 f9 Auto NEC 83 F4 08 f7 Source NEC 83 F4 04 fb Blank NEC 83 F4 07 f8 Menu NEC 83 F4 10 ef Digital Zoom+ NEC 83 F4 18 e7 Digital Zoom- NEC 83 F4 19 e6 ViewMatch
Function Brightness Status Write Read Aspect ratio Write Read Auto Adjust Horizontal position CMD 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61 Brightness increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62 Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62 Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 Aspect
Function Blank Status Write Read KeystoneVertical Write Read Write Preset mode Read Write Freeze Read Source input Write Read Write Source scan Read Mute Write Read Volume Write Read 54 Appendix Action CMD Blank on 0x06 0x14 0x00 0x03 0x00 0x34 0x12 0x09 0x66 Blank off Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Keystone status 0x07 0x14 0x00
Function Status Action CMD 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 Language 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 Write 0x06 0x14 0x0
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. T=Telephone Country/Region Web Site Australia/New Zealand www.viewsonic.com.au Canada www.viewsonic.com T (Toll-Free)= 1-866-463-4775 T (Toll)= 1-424-233-2533 F= 1-909-468-1202 Europe/Middle East/Baltic countries/North Africa www.viewsoniceurope.com Contact your reseller Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.
Limited Warranty VIEWSONIC® PROJECTOR What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Limitation of implied warranties: There are no warranties, express or implied, which extend beyond the description contained KHUHLQ LQFOXGLQJ WKH LPSOLHG ZDUUDQW\ RI PHUFKDQWDELOLW\ DQG ¿WQHVV IRU D SDUWLFXODU SXUSRVH Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1.
Mexico Limited Warranty ® VIEWSONIC PROJECTOR What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col.
Downloaded From projector-manual.
