Specifications

ManualsBrandsViewSonic ManualsProjectorPJ1060

Quick Start Reference Sheet

Viewsonic PJ1060

Revision A

DR-VWS03 - 12/18/03

SP Controls reserves the right to modify specifications without notice at any time.

NOTE: This document is intended only as a quick reference for installation – please read the SP

Controls Application Note for a complete description of this projector driver prior to installation.

I. Driver Features

1. Input Selection Mapping

Selection 1: VIDEO

Selection 2: VIDEO

Selection 3: RGB 1

Selection 4: RGB 2

2. Hidden Function Mapping (Default Configuration)

Using the ON button as a shift key, press the following buttons to access the specified projector features.

Selection 1: BLANK

Selection 2: MUTE

Selection 3: ADJ LEFT

Selection 4: ADJ RIGHT

Off: MENU

Volume Up: ADJ UP

Volume Down: ADJ DOWN

3. Other Driver Features

Power Status Feedback Method RS-232 Power Polling

Control Wiring RS-232 and Infrared Emitter

II. Wiring Specifications

NOTE: For a wiring diagram, please see the SP Controls Application Note.

1. RS-232:

Wire the Panel RS-232 port to a female HD15 as follows:

TX to 13

RX to 14

GND to 10

Connect this female HD15 to the projector port labeled CONTROL.

2. Infrared Emitter:

Wire the Panel IR/Serial port to a female 1/8" Mini as follows:

IR/SER to tip

GND to ring

Connect to the included IR Emitter and attach the emitter bud to any projector IR window.

III. Additional Projector Information

The MP8670 must be configured in the following way for use with the Panel:

• Baud Rate 9600: Set the projector to 9600bps in the onscreen OPT. (OPTIONS) Menu: COM.

SPEED setting.

• Data Word 8N1: Set the projector to use data word 8N1 in the onscreen OPT. (OPTIONS) Menu:

COM. BITS setting.

Summary of content (6 pages)

PAGE 1
Quick Start Reference Sheet Viewsonic PJ1060 Revision A NOTE: This document is intended only as a quick reference for installation – please read the SP Controls Application Note for a complete description of this projector driver prior to installation. I. Driver Features 1. Input Selection Mapping Selection 1: Selection 2: Selection 3: Selection 4: VIDEO VIDEO RGB 1 RGB 2 2.
PAGE 2
Projector Driver Application Note Viewsonic PJ1060 Revision A This document describes the Smart Panel Projector Driver for the Viewsonic PJ1060 projector. For more information on configuring and using the Panel see the Smart Panel Configuration and Installation Guide. Please read the SPECIAL CONTROL NOTE below before attempting to control the Viewsonic. This driver is known to work only when the projector is configured for serial communication at 9600 8N1. I. PROJECTOR CONTROL A.
PAGE 3
Smart Panel Projector Driver Application Note Viewsonic PJ1060 The hidden functions available for the Viewsonic with this Driver are as follows: MENU ZOOM + ZOOM – FOCUS + FOCUS – ADJ UP ADJ DOWN ADJ LEFT ADJ RIGHT BLANK MUTE RIGHT CLICK LEFT CLICK POSITION TIMER D. Relays 500mA MAX. CURRENT 1 7B 7A 6B 6A 5B 5A SELECTION (EXT. SWITCHER CTRL) 3 2 4B 4 4A 3A 3B PWR OFF MOM. 2B PWR ON MOM. 2A ON Maintained ON Momentary OFF Momentary Momentary; not Binary PWR ON MAINT.
PAGE 4
Smart Panel Projector Driver Application Note Viewsonic PJ1060 II. CONTROL WIRING This section specifies how RS-232 and Infrared should be wired to the Viewsonic projector. PROJECTOR CONTROL Female HD15 TX to pin 13 RX to pin 14 GND to pin 10 A. RS-232 should be connected to the D-sub 15 female terminal labeled CONTROL. Connection should be as follows: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 GND SENSE IR/SER +12V GND IR/SERIAL CTS RTS TX RX RS232 1/8" Mini Female 1.
PAGE 5
Smart Panel Projector Driver Application Note Viewsonic PJ1060 III. TROUBLESHOOTING Additional tips can be found in the Smart Panel Configuration and Installation Guide. The Panel does not do anything at all. When power is applied to the Panel it should run through a brief power on self-test, during which all of the Panel lights will turn on and off in sequence. If you do not see this self test, make sure power is connected correctly and that polarity is correct.
PAGE 6
Smart Panel Projector Driver Application Note Viewsonic PJ1060 V. REVISION HISTORY 1. Revision A (December,2003) Initial Release © 2003 SP Controls Inc. 601 Minnesota Suite 115, San Francisco, CA 94107 help@spcontrols.