ViewSonic by Premier Mounts INSTALLATION INSTRUCTIONS PJ-WMK-006 Universal Projector Mount NORTH AMERICA 1321 S. State College Blvd.
PJ-WMK-006 Table of Contents Warning Statements .............................................................................................................................2 Part List ................................................................................................................................................3 Installation Tools ....................................................................................................................................3 Features ..................
PJ-WMK-006 This Mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700). Included components x4 x1 M2.
PJ-WMK-006 Features Congratulations on your recent purchase of your PBC Universal Projector Mount. This mounting system is designed for projectors weighing 60 lbs. (27.2kg) or less. The mount is easy to install and is loaded with additional installation features built into the mount. These features allow you to optimize the projector's position to the screen for the best projector performance and picture quality.
PJ-WMK-006 Projector Preparation Step 3. Separate the upper assembly from the projector mounting bracket by slightly loosening the two tension knurl knobs to create free play between the bracket tri-lock assembly and the upper section tri-lock assembly points (Figure 2A and 2B). Step 4. Loosen the security screw knurl knob far enough to allow the two parts to be rotated 180º apart and separate (Figure 2C).
PJ-WMK-006 Bracket Installation Only attach to the projector manufacturer's specified mounting points on the projector chassis with a minimum of three mounting legs. Please follow all safety instructions specified by the projector manufacturer as well as the safety instructions outlined in this manual. The two-piece mounting legs are designed to allow for the positioning of each leg around projector air vents located on the base of the projector.
PJ-WMK-006 Leveling the Mounting Bracket Secure but do not overtighten the mounting hardware. Overtightening will result in damaging the threads in the projector. Step 1. Rotate the leveling barrels to level the mounting bracket. Step 2. Position the mounting bracket so that it avoids most, if not all, ventilation points (including lamp and filter access doors). Step 3.
PJ-WMK-006 Securing the Upper Assembly Ceiling Plate 1 2 Minimum of 2 X 4 wood stud to be used Use a pencil and mark 2 mounting hole locations through nn Use a stud finder to locate a ceiling stud closest to your nn the slots. desired installation location. Identify the center of the ceiling stud. oo Use a pencil to mark the location of the ceiling stud center. pp 4 3 (2) #14 x 2" Wood Screw Drill a “pilot hole” in the center using a 1/8” drill bit and power drill.
PJ-WMK-006 Securing the Projector to the Upper Assembly Step 1. Make sure the three knurl knobs are loosened to fully expose to the "tri-lock" mounting plate in the base of the upper assembly. Step 2. Carefully lift the projector and insert the mounting bracket mating special tri-lock cutout into the mating portion of the upper assembly. Step.
PJ-WMK-006 Final Adjustments Step 1. With the projector secured in the mount and power on and signal supplied to the projector you can now proceed with the final height, tilt, roll and yaw to optimize the projected image. Wooden Stud Ceiling Structure A A Locking Set Screw The height can be adjusted by rotating the coupler clockwise (higher) / counterclockwise (lower). Once the height is achieved, tighten the locking set screw using the supplied Security Allen Wrench.
PJ-WMK-006 Plastic Cap Installation Step 1. Once all the final adjustments have been finished, install the plastic caps on the leveling barrels (Figure 8). Figure 8.
PJ-WMK-006 Technical Specifications All measurements are in inches (mm). Security 1.5” (NPT) Nipple Figure 9. Technical Dimensions Figure 9.
PJ-WMK-006 WMK-005 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original installation of this product. The limited warranty is valid only for the original purchaser of the product.
