PJ-vTouch-10S Projector Interactive Kits User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www.viewsonic.
Thank you for choosing ViewSonic As a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic product you have chosen will serve you well.
Compliance Information Please read before proceeding • Use only the batteries and power adapter provided by the manufacturer. The use of unauthorized accessories may void your warranty. • Do not store your device in temperatures higher than 50°C (122°F). • The operating temperature for this device is from 0°C (32°F) to 35°C (95°F). FCC Notice The following statement applies to all products that have received FCC approval.
FCC SAR Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration 0.1% 0.1% 0.01% 0.1% 0.1% 0.
Copyright Information Copyright © ViewSonic® Corporation, 2017. All rights reserved. ViewSonic®, the three birds logo, OnView®, ViewMatch™, and ViewMeter® are registered trademarks of ViewSonic® Corporation. Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
Contents Compliance Information Please read before proceeding...............................................................................i FCC Notice..............................................................................................................i FCC SAR Information.............................................................................................ii CE Conformity for European Countries..................................................................
Troubleshooting The stylus pen does not work...............................................................................18 The finger touch operation does not work............................................................18 Lines traced with the stylus pen do not match screen..........................................18 You can check the installation condition of the camera unit when the troubleshooting in the EyeRIS setup menu is displayed on.................................
Packaged Items Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Part names of the supplied stylus pen Tip LED indicator Charging jack (Mini USB) Charging Stylus Please use the Stylus charging cable and connect the charging jack of Stylus to a USB port on a computer and Stylus will start charging; it takes approximately 3 minutes to charge Stylus. • Press the tip of Stylus and the LED indicator will turn red. This means that Stylus charging is completed.
2 Setup Procedure Setup Flow • Mount the camera onto the projector. • Connect the projector to the computer. • Turn on the power of the projector and adjust its position and focus of the projection. • Connect the computer and camera using the USB cable. • Laser Module installation • Install the driver and calibration software on the computer and perform calibration. 1. Mounting the camera onto the projector.
ick Start Guide Magnet or Adhesive and solution Kit PC System Requirements Intel® Pentium® processor o r greater running on Windows® Platform, 4x CD-ROM drive; 64MB or more of available RAM; 800x600 color display. 4. Laser Module installation Mac® System Requirements Mac OS version 10.x; 4x CD-ROM drive; 64MB or more of available RAM; 800x600 color display. All rights reserved. All trademarks, eir respective companies.
4 6. The laser module must be installed for the finger touch control function, and the laser light must be adjusted parallel to the surface of the screen. Please perform adjustments according to the steps below: 6.1 Open the top cover of the Laser Module and press the Red Laser switch; a levelled laser beam will appear used to calibrate the flatness of the Laser Module and whiteboard.
6.2 Red Laser flatness calibration steps: 6.2.1 Adjust Gear B; make the distance between the two points b / c in the image below and the whiteboard parallel. 6.2.2 Adjust Gear A, check and make sure that the distance between the two points b / c and the whiteboard is 6±1.5mm. 6.2.3 Check and make sure that the distance between the three points a / b / c and the whiteboard is approximately 6±1.5mm. 6.2.4 Calibration complete; press the red laser switch to turn off the red laser.
Operating Environment / EyeRIS Supported OSs are as follows Windows 7, Windows 8/8.1 and above • For starting up the software, Microsoft .NET Framework 4 or later is required. Download the Microsoft .NET Framework from the website of Microsoft and install it onto the computer. About trademarks Microsoft, Windows, .NET Framework are either registered trademarks or trademarks of Microsoft Corporation in the U.S. or other countries.
1. Download the software Access to our projector support page in our website with the below URL: HTTP://www.viewsonic.com/support/ Find the software for the IWB Setup Software, EyeRIS, download and install it onto the computer according to the displayed instructions. 2. Double click [EyeRIS_3.0.6.21_20160517_ViewSonic.msi] The Setup window is displayed. 3. Click [Next>]. Displays the Terms of Use screen. 4.
5. Click [Next>]. After that, follow the displayed instructions to complete installation. When the installation is complete,EyeRIS and SensorViewer icon is added to the desktop.
How to uninstall the software 1. Click [Control Panel] in the start menu, and double-click [Add or Remove Programs]. 2. Right-click [EyeRIS] and click [Uninstall] in the list. After that, follow the displayed instructions to complete uninstallation. 3. When uninstallation is completed properly, reboot the computer.
Startup the Software Preparation: • First of all, perform setup according to the user’s manual supplied with the projector or the installation manual supplied with the Interactive White Board Kit or the Touch Module. • If the computer and the camera unit are not connected by a USB cable, the message at right would be displayed on and the software would not be started up. 1. Double click the EyeRIS icon on the desktop. Driver installation message is displayed on.
Calibration Menu Display Indicate status of the stylus pen or the finger touch operation. [Calibrated] The stylus pen or the finger touch operation is ready to use [Not calibrated] Cannot use the stylus pen or the finger touch operation because calibration is not performed, or the trouble shooting is displayed on Indicate connection status of the camera unit and the computer Close EyeRIS Setup Menu. * The software will continue to run. It will be displayed when you detect your software update.
Performing Calibration Before starting to use the stylus pen or the Touch Module, make sure to perform calibration in order to make the computer to recognize exact position touched by the stylus pen or a finger. Start Manual Start Automatic Align Finger Touch Module Automatically calibrate the stylus pen position. Recommend this when simple calibration is preferred. Manually calibrate the stylus pen position. Recommend this for installing the projector permanently or when precise calibration is preferred.
Perform Calibration Automatically [Automatic Calibration] Click the [Start Automatic] button on the displayed calibration menu. Projected image on the screen will be switched to the Automatic Calibration Screen After five to eight seconds, calibration will be completed and the screen will return to display the projected image.
Perform Calibration Manually [Manual Calibration] 1. Click [Start Manual] button on the displayed calibration menu. Projected image on the screen is switched to the Manual Calibration Screen and red dot is indicated at the top left on the screen. 2. Press the center of the red dot with the stylus pen. The red dot is indicated at 25 points in order on the screen. Press briefly on the red dot to calibrate (see top left). Use Stylus.
3. Touch icon in the task tray by the stylus pen. This message is popped up when calibration is completed properly. 4. In order to align EyeRIS more precisely with visual aid, click on Power button to exit EyeRIS U I and Open "Sensor Viewer"application to physically align EyeRIS module with Projection area. Open "Sensor Viewer" application from START » All Programs » EyeRIS » Sensor Viewer 5. A live-feed of EyeRIS image sensor can be seen as below.
Troubleshooting Tips: If the Projection area is not visible due to high ambient light, try reducing and click "Confirm" to adjust to the reduced or increased exposure settings. Please note that this adjustment is just to confirm that projection area is fully covered by EyeRIS sensor and has no correlation with the working of EyeRIS. Notes: • For disconnecting the USB cable connecting the computer and the camera unit, make sure to exit for finishing the software.
Troubleshooting The stylus pen does not work • Have the driver and the calibration software been installed on the computer? • Is the USB cable connected between the computer (type A USB port) and the camera unit (type Mini USB port)? • Has calibration performed properly? Even calibration is performed at the beginning, please perform calibration again when the stylus pen becomes inactive during operation • Are you using the stylus pen in one of the following environment? - If direct sunlight strikes the scr
You can check the installation condition of the camera unit when the troubleshooting in the EyeRIS setup menu is displayed on • Troubleshooting screen Change the stylus pen status. Switch to the calibration menu If clicking / pressing this by the mouse / the stylus pen when PAUSE CALIBRATION is indicated on this button, the stylus pen becomes unavailable. Enable/disable the Auto Run function. When this function is checked, the software starts automatically when the computer is started up.
Windows Operating System Version Windows 8.1 Windows 8 Windows 7 Windows 10 Windows 8.1 Windows 8.1 Pro Windows 8 Windows 8 Pro Windows 8 OEM Windows 7 Home Premium Windows 7 Professional Windows 7 Enterprise Windows 7 Ultimate Windows 10 Home Windows 10 Pro 20 CNY EyeRIS 3.1.
Specifications • Camere • Output resolution: 752 x 480 • Frame Rate: 60 fps/sec • Optical Lens: 1/3.2 inch // F#2.8 // FOV-D 181 degree // TTL18.80mm // 6G // M12 14pie • Tracking Active Area: 100" for 16:9 aspect ratio / 80" for 4:3 aspect ratio • Inter-Finger Distance Specification: Middle/Center <3CM, Left &Right Side(Bottom)< 4.5CM • Connector: Mini USB × 1 • Power Consumption: 5 V/120mA, Less than 1 watt • Weight: 60 g/ 2.
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Country/Region Website T= Telephone C = CHAT ONLINE Email Australia New Zealand www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 service@au.viewsonic.com Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com Europe www.viewsoniceurope.com http://www.viewsoniceurope.com/eu/support/call-desk/ Hong Kong www.hk.viewsonic.
Limited Warranty ViewSonic® Wireless Presentation Gateway What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Limitation of implied warranties: There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose. Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1.
Mexico Limited Warranty ViewSonic® Wireless Presentation Gateway What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.