ＷＡＮ口 ＬＡＮ口 Ｐｏｗｅｒ ＬＡＮ ｐｏｒｔ ｃｏｎｎｅｃｔ ｗｉｔｈ ａ ＰＣ ｏｒ ａ ｒｏｕｔｅｒ Ｐｏｗｅｒ ＰＯＥ ｐｏｒｔ ｃｏｎｎｅｃｔ ｄｅｖｉｃｅ ＬＡＮ ｐｏｒｔ （ｓｕｐｐｌｙ ｐｏｗｅｒ ｔｏ ｔｈｅ ｄｅｖｉｃｅ） ＮＯＴＥ ：Ｕｓｅ ＬＡＮ ｐｏｒｔｓ ｏｆ ｔｈｅ ｄｅｖｉｃｅ ｔｏ ｌｏｇ ｉｎ ｓｏｆｔｗａｒｅ
Ｓ ｅｔ ｙｏｕｒ ＩＰ ｔｏ ＂Ｕｓｅ ｔｈｅ ｆｏｌｌｏｗｉｎｇ ＩＰ ａｄｄｒｅｓｓ＂ 192.168.110.3 255.255.255.
ＡＰ Ｍｏｄｅ （ｓｅｎｄｉｎｇ）＋ＷＤＳ DHCP Connection Basic Authentication DHCP LAN DHCP Server Enabled DHCP range： Start： End： Lease Time： 192.168.110. 10 192.168.110.
＋ＷＤＳ １．Ｃ ｈａｎｇｅ ＷＡＮ ｐｏｒｔ ｉｎｔｏ ＬＡＮ ｐｏｒｔ ａｃｃｏｄｒｉｎｇ ｔｏ ｄｅｍａｎｄ ２．Ｓ ｅｔ ｕｐ ＩＰ ａｄｄｒｅｓｓ ｏｆ Ｒ ｏｕｔｅｒ （ｆｏｒ ｅｘａｍｐｌｅ：１９２．１６８．１１０．１） ３．Ｓ ｅｔｔｉｎｇ Ｓ Ｓ ＩＤ， ｓｃａｎ ｔｈｅ ａｖａｌｉａｂｌｅ ｗｉｆｉ ｓｉｎｇａｌ ６ ADSL AP+WDS Wireless Bridge/Repeater Bridge IP： 192.168.110.2 (must be in AP subnet) Subnet Mask： 255.255.255.0 (same as AP mask) AP/Gateway IP： 192.168.110.1 Wan Ethernet Port： Disable DNS Servers: Use Gateway As DNS Server Connect Via WDS Operation Mode： N+A Channel Width： 40MHz (2nd chan.
ADSL Current IP： Current Lease Expires： Renew Lease Now Wan Ethernet Port： Disable AP+WDS Wireless Ｄｅｆａｕｌｔ ｂａｎｄｗ ｉｄｔｈ Disable SSID to Join: MAC Binding(Blank if not binding): Wireless Channel: Encryption: Access Point SSID: 1111 2462MHz[11] None 2222 2452MHz[11] None Clients Quantity Ｉ scan
FCC Warnning: ７－ １０ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
