VNT6656GEV00 USER'S MANUAL Revision 1.0 June 6, 2006 VIA TECHNOLOGIES, INC.
Copyright Notice: Copyright © 2006, VIA Technologies, Incorporated. All Rights Reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written permission of VIA Technologies, Incorporated. VNT6656GEV00 may only be used to identify WLAN products of VIA Technologies, Inc.
User's Manual VIA Technologies, Inc. Revision History Release 1.0 Date 2006-06-06 Revision 1.0 • June 6, 2006 Revision Initial release.
User's Manual VIA Technologies, Inc. Table of Contents 1. Features........................................................................................................................ 1 1.1. Drivers and Applications.......................................................................................... 1 1.2. Certifications ........................................................................................................... 1 1.3. Software Packages ........................................
For OEM integrators This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required.
Hardware Installation & Antenna Information Module is installed in the Personal Computer, located on the bottom side of the Personal Computer. Antennas are embedded in the two sides (see the two antennas shown below) Only the antenna types listed below can be used: Antenna 1: PIFA (Model: 6-23-7M59K-021 , made by FAVORTRON CO., LTD) Antenna 2: PIFA (Model: 6-23-7M59K-011 , made by FAVORTRON CO., LTD) Antenna 3: PIFA (Modle: 13-130-F14911, made by VSO ELECTRIC CO.
*Caution !! (1). This module cannot be bound in a tablet computer for RF exposure issues. (See label 1) (2). Due to the RF exposure issues, this module can be used in a laptop computer in normal operation, but cannot be used when it is put above the lap and the LCD screen is in the closed position.
(3). This module must be labeled with FCC ID. (See label 3) Label 3 (4). If the FCC ID is not visible when the module is installed inside another device, then the outside of device must also display a label referring to the enclosed module. The exterior label can be “ Contains Transmitter Module FCC ID:NKRDRCM ” or similar wording. (See label 4) Contains Transmitter Module VNT6656GEV00 FCC ID: NCI-VNT6656GEV0X Label 4 Please put Label 3 & Label 4 to the enclosure of end product to note the end user.
User's Manual VIA Technologies, Inc. 1. Features 1.1. Drivers and Applications Drivers available for Microsoft Windows 98/ME/NT/2000/XP and all major distributions of Linux. Setup utility for automatic driver installation on Windows. Mass-production support tool. Mass-production application interface for custom programs. PATCH utility for driver customization. This utility allows the manufacturers to customize the driver packages, such as changing the drivers’ icons and file names. 1.
User's Manual VIA Technologies, Inc. 2. Drivers and Utilities 2.1. Drivers DRIVER TYPE DESCRIPTION NDIS 5 Supports Windows SE, ME, 2000, XP, XPe, and Sever 2003. NDIS 4 Supports Windows NT 4.0. WinCE 4.2 Supports Windows CE 4.2. WinCE 5 Supports Windows CE 5.0. x64 Supports AMD 64-bit CPUs. 2.2. Utilities for end users UTILITY NAME DESCRIPTION Winsetup Automatic driver installation, uninstallation, and updating utility for Windows 98 SE, ME, NT 4.0, 2000, XP, and Sever 2003.
User's Manual VIA Technologies, Inc. 3. Software Package Information 3.1. Directory structure DIRECTORY DESCRIPTION / (Root directory) Drivers for Windows 98 SE, ME, NT 4.0, 2000, XP, and Sever 2003; release note; and other documentations. /XPe Driver for Windows XP Embedded. /WIFISET Wireless configuration setup tool for Windows. /WINSETUP Windows driver setup utility for Windows 98 SE, ME, NT 4.0, 2000, XP, and Sever 2003. /MPTOOL Mass-production tool and the EEPROM layout guide.
User's Manual VIA Technologies, Inc. 3.2. Driver Keywords/Parameters Figure 1. Properties—Advanced Adhoc Beacon Interval Defines the beacon interval in the ad hoc mode. Antenna Diversity Enables or disables antenna diversity. Connection Rate Specifies the connection rate (in Mbps): 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54, or Auto. Default Channel The user-defined connection channel—applicable in the ad hoc mode and AP mode.
User's Manual VIA Technologies, Inc. Network Address The user-defined network address—overrides the network address originally set by the hardware vendor. Operation Mode Determines the operation mode: Infrastructure or Ad Hoc. Preamble Type Determines the acceptable preamble type: Select Long to accept long preambles only; select Short to support short preambles. RadioControl Determines whether the radio is on or off. Receive Buffers Defines the size of the internal driver buffers for received packets.
User's Manual VIA Technologies, Inc. 4. Windows Utilities 4.1. WiFiset1 The VIA WiFiset is a Windows-based application. Its main features are listed below. 4.1.1. Status Displays the network status of the device. Figure 2. WiFiset—Status 4.1.2. Config Displays and controls the link configurations for the device. 1 To avoid software conflict, WiFiset does not synchronize its settings with Windows Zero Configuration (WZC), nor vice versa. Revision 1.
User's Manual VIA Technologies, Inc. Figure 3. WiFiset—Config SSID The service set identifier (SSID) is the name given to a wireless network by its administrator(s). The default value is Any, which allows the device to connect to any access point in the Infrastructure Mode, or to any other wireless device in the Ad Hoc Mode. The SSID can be up to 32 characters long, and is case sensitive.
User's Manual VIA Technologies, Inc. Radio Status Shows whether the radio is on or off. Data Rate Selects the rate of transmission between your computer and the access point (in the infrastructure mode) or another wireless device (in the ad hoc mode). In general, a higher transmission rate would provide a smaller coverage area, and a lower transmission rate would cover a greater distance.
User's Manual VIA Technologies, Inc. Figure 4. WiFiset—WEP config Encryption state Determines whether Wired Equivalent Privacy (WEP) is used for data encryption. • None (default) No encryption. • WEP Data is encrypted with a WEP key. Up to four WEP keys can be specified. Each key can have a length of 40, 128, or 256 bits. Authentication Mode Determines the method of authentication.
User's Manual VIA Technologies, Inc. 4.1.3. Site Survey Displays a list of all available networks within range. Figure 5. WiFiset—Site Survey Join Network Joins the device to the selected network. Re-Scan it! Re-scans to discover all currently available networks within range. Revision 1.
User's Manual VIA Technologies, Inc. 4.1.4. Statistics Displays the real-time transmission and reception statistics of the device. Figure 6. WiFiset—Statistic Pause Pauses, or freezes, the currently displayed statistics. Clicking Pause again will resume the real-time display. Reset Resets all values to zero. 4.1.5. Signal Displays the current and past values of signal strength (SS) and signal quality (SQ) for the connected network. Revision 1.
User's Manual VIA Technologies, Inc. Figure 7. WiFiset—Signal 4.1.6. Profiles A profile is a set of preconfigured settings for a particular network environment. Having different profiles stored in WiFiset, you can move from one network to another without having to reconfigure the network settings. 4.1.6.1. Adding a new profile Before adding the current network configuration as a new profile, make sure that your device is connected to a network and that all settings are properly configured.
User's Manual VIA Technologies, Inc. Figure 8. WiFiset—Adding a new profile Step 2. Enter a name for the new profile, and then click OK. Figure 9. WiFiset—Profile Name Revision 1.
User's Manual VIA Technologies, Inc. Step 3. The new profile is now successfully added to the Profile List, and it’s set to be a default one automatically. Figure 10. WiFiset—New profile added 4.1.6.2. Default profile and automatic connection You can configure your device to automatically connect to a network according to the default profile. Step 1. Select a profile name from the Profile Select box. Step 2. Click the Default Profile button. Step 3.
User's Manual VIA Technologies, Inc. Figure 11. WiFiset—Auto Connect with Default Profile Note: Once the device is set to automatically connect with a netowork according to the default profile, most of the options under WiFiset’s Config tab would become unavailable, and therefore appear dimmed—except for Power Save Mode and Auto connect. In addition, a check mark would now appear in the Auto connect check box. Revision 1.
User's Manual VIA Technologies, Inc. Figure 12. WiFiset—Auto connect 4.2. WPA Networking VT6655 supports Windows XP Wireless Zero Configuration service for connecting to a Wi-Fi Protected Access (WPA) network. Step 1. Open Wireless Network Connection. Revision 1.
User's Manual VIA Technologies, Inc. Figure 13. Wireless Network Connection Step 2. Click a wireless network from the list of available networks, and then click Connect. Step 3. Enter the network key, also known as WEP key or WPA key. Revision 1.
User's Manual VIA Technologies, Inc. Figure 14. Wireless Network Connection—Network key Revision 1.
User's Manual VIA Technologies, Inc. Appendix A: Terminology ad hoc network A network composed solely of stations within mutual communication range of each other via the wireless medium (WM). access point (AP) Any entity that has station functionality and provides access to the distribution ser-vices, via the wireless medium (WM) for associated stations. Station (STA) Any device that contains an IEEE 802.
User's Manual VIA Technologies, Inc. Appendix B: Important Notices Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User's Manual VIA Technologies, Inc. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
User's Manual VIA Technologies, Inc. Manual Information That Must be Included The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrate this module.
