Use and Care Manual

ManualsBrandsVEVOR ManualsElectricalMotorized TV Lift Stroke Length 35 in. Motorized TV Mount Fit for 32-65 in. TV Lift with Height Adjust 28.7-64.2 in.

Single column controller instruction manual

I.Function introduction

Intelligent single column controller has the following

characteristics:

1.It can control two motors` output to achieve

synchronous operation;

2.Showing the operating height every time;

3.Four-phase position setting and outage memoty;

4.It will rebound when meeting resistance.

II.System parameters

1.Input voltage:DC29V;

2.Input current: recommending above 1.8A and

according to the load;

3.Maximum output voltage of motor interface:DC29V;

4.Maximum output current of motor interface:4A;

5.Operating temperature:0~40℃

6.Working humidity:20~90%;

7.Storage temperature:20~70℃.

III.System connection

a.Handheld controller b.Main controller

c.telecontroller d.Non-part of the system

Summary of content (6 pages)

PAGE 1
a c b d Single column controller instruction manual I.Function introduction Intelligent single column controller has the following characteristics: 1.It can control two motors` output to achieve synchronous operation; 2.Showing the operating height every time; 3.Four-phase position setting and outage memoty; 4.It will rebound when meeting resistance. II.System parameters 1.Input voltage:DC29V; 2.Input current: recommending above 1.8A and according to the load; 3.
PAGE 2
IV.Motor interfase plug definition: Motor power:+(-) 0~29VDC Motor power:(+)Hall switch:2ch Hall switch:GND Hall switch: 1ch 5VDC Hall switch:Vcc V.Fault code and its treatment 1.Fault code Err1 When the manual controller shows Er1,it`s a foult of Err1.It meas there is something wrong with M1 interface channel (see the following picture).For exemple ,motors are not connected in a positive way;Hall sidnal boar is not connected;Paper line,etc.
PAGE 3
VI.System reset 1.Prompt reset When the manual controller shows ″RST″(see the following picture),the whole system needs to reset maunally. 2.Line reset When the manual controller shows the minimum heigh(for example,for a system with a reset height of 60cm,see the following picture),pressing″down button″ more than 5 seconds. When the manual controller shows RST,releasing the hand and starting to reset system. 3.
PAGE 4
The colunm will rise5~10mm after a short time when it reach the lowest point. After all arrive,rising a small distance. When the manual controller ″RST″disapper(see the following picture),releasing the hand and end at resetting. VII.Preset the target height 1.The number of presetting target height: The system provide 4 sets of target height,all of them can be saved more than 10 years. 2.
PAGE 5
In 2 seconds,pressing 2 before ″SET″ disappears Displaying ″S-2″means setting over. 5.The way of using target height: At any height(reset state,wrong state unable to perform this operation),can quickly reache for the target height by 1~4 keys. VIII.The way to change height 1.Colunm elongation 1).Operating by Handheld controller :Using″up button″ to achieve longation operation,stopping when travel limit.Releasing hand is the order to stop but not quickly.It stops after a short distance. 2).
PAGE 6
P: 1.Do not pass the″up button″ in 3 seconds repowering 2. Do not release when passing the″up button″ 3.The buzzing sound for success of matching is:di~~di~~di~~di~~ di~di~di~ 4.Releasing after liseaning the right buzzing sound 2).Operating by telecontroller :Using″down button″ to achieve longation operation,stopping when travel limit.Releasing hand is not the order to stop,passing any key again will stop,but not quickly.It stops after a short distance. IX.Telecontroller operation 1.