INSTRUCTION MANUAL HEAVY-DUTY PIPE GRAB MODEL PG (CAST IRON & STEEL) FRONT VIEW SIDE VIEW MODEL NO. ________________________ SERIAL NO. ________________________ VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868 FAX: (260) 665-1339 URL: WWW.VESTILMFG.COM EMAIL: SALES@VESTIL.
We produce several models of heavy duty pipe grab so that our customers may select a product that satisfies specific requirements. The products identified on the front page conform to the generalized specifications disclosed in this manual. Each model fulfills our demanding standards for quality, safety and durability. SAFETY PRINCIPLES Vestil Manufacturing Corp. recognizes the critical importance of workplace safety.
TABLE OF CONTENTS Safety Principles Product Introduction Safety Guidelines Use Instructions Inspections & Maintenance Markings 2 4 5 11-13 13-14 15 TABLE OF FIGURES FIG. 1: Labeled Photograph FIG. 2: Exploded Parts Diagram for PG-C/S-045 & PG-C/S-060 FIG. 3: Exploded Parts View for Models PG-C-100, PG-S-100 FIG. 4: Exploded Parts View for Models PG-C-140 and PG-S-140 FIG. 5: Exploded Parts View for Models PG-C-200 and PG-S-200 FIG.
PRODUCT INTRODUCTION Thank you for purchasing a Heavy Duty Pipe Grab (“pipe grab” or simply “grab”) made by Vestil Manufacturing Corporation (“Vestil”). Each pipe grab is a durable, high-quality product that combines safety features and superior lifting capabilities. Despite ease of use, all personnel must familiarize themselves with the safe operation instructions provided in this manual. We produce 2 main types of heavy duty pipe grab, the PG-C and PG-S.
SAFETY GUIDELINES Read the entire manual before attaching the pipe grab to a lifting device or using it for the first time. Refer to the manual for safe use and maintenance procedures (p. 11-14). If questions remain after you finish reading the manual, contact Vestil for answers. DO NOT attempt to resolve any problems with the pipe grab unless you are certain that it will be safe to use afterwards. NEVER modify the product in any way without the express written approval of Vestil.
FIG.
FIG. 2: Exploded Parts View for Models PG-C-045, PG-C-060, PG-S-045, PG-S-060 Item No. 1 Part No.
FIG. 3: Exploded Parts View for Models PG-C-100, PG-S-100 Item No. 1 2 3 4 5 6 7 Part No.
FIG. 4: Exploded Parts View for Models PG-C-140 and PG-S-140 Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part No. 28-514-168 28-014-199 28-014-200 28-016-090 28-516-044 28-014-201 26351 11109 37024 33008 28-112-024 28-112-025 33012 33434 68017 Description Lever Arm Weldment with Stop Block Lever Arm (Frame) Top Link (Frame) Formed Hook Bracket Outrigger Arm Weldment Link Arm (Frame) Socket Head Shoulder Bolt, ½ x 1-1/4 with ¼ Hex.
FIG. 5: Exploded Parts View for Models PG-C-200 and PG-S-200 Item No. 1 2 3 4 5 6 7 8 9 10 Part No.
Use Instructions: The operating instructions in this manual are meant to supplement the operating recommendations of ASME standard B30.20. Only trained, designated persons should use the Pipe grab. “Designated person” means someone selected by his or her employer, or by a representative of the employer, as competent to use the pipe grab. Trainees under the direct supervision of a designated person may use the device.
7 Step 5: Make sure that the load is balanced. Lift the load just a few inches off of the ground or supporting surface to see if it remains horizontal. If the load hangs lower on one side of the grab, lower the load until it fully rests on the ground/supporting surface and immobilize it. Release the load by lifting one of the pipe guide weldments. Move the grab slightly towards the end of the load that hung lower. Raise the object again just a few inches into the air to check the balance of the load.
Step 7: Lower the load to the ground/supporting surface (photos 11 and 12). Position the object above the surface that will receive it (ground, pallet, work platform, etc.). Make sure that the load is not swinging or rotating before beginning to lower it. 11 12 Step 8: Once the load has been fully lowered, immobilize it. Disengage the pipe grab by lifting one or both of the pipe guide weldments. Raise the grab so that it is completely free of the load.
Inspections Before & During EVERY lift: visual examination must be performed by the operator prior to AND during each lift. In particular, the operator should inspect for: 1. Debris on the load surfaces; AND 2. Condition and operation of the controls. Frequent Inspections: the specific meaning of “frequent” varies from daily to monthly depending on the service classification (normal, heavy, severe, and special/infrequent) of the pipe grab. Definitions of the service classifications appear in ASME B30.20.
Markings: Only use the pipe grab if ALL of the labels are readable and undamaged. Contact Vestil for replacement labels. FIG.
