Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 EVX-261 OPERATING MANUAL PROGRAMMABLE FUNCTIONS/FEATURES IP55 Water Resistant Two Programmable Function Keys 2-Tone Encode/Decode 5-Tone Encode/Decode MDC-1200® Encode (ANI Encode) DTMF Encode Scan Dual Watch Follow-Me Scan Talk Around Scan Encryption VOX Talk Around Emergency Selective Call (2-Tone/5-Tone/Digital) Remote Control Decoder (Digital only) Transmit Battery Saver ARTS™ (Auto Range Transpond
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 CONTENTS Introduction ..................................................................... 1 Class B Digital Device ..................................................... 2 Warning! FCC RF Exposure Requirements................. 3 Warning! IC RSS General Requirement ...................... 5 Before You Begin ............................................................. 7 Battery Pack Installation and Removal .......................
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 INTRODUCTION The EVX-261 is full-featured Hand-Held Digital/Analog Transceiver designed for business communications in the VHF/ UHF Land Mobile bands. The EVX-261 supports up to 16 user configurable channels supporting a wide variety of business applications.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 CLASS B DIGITAL DEVICE NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 WARNING! FCC RF EXPOSURE REQUIREMENTS THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 WARNING! FCC RF EXPOSURE REQUIREMENTS 4 When transmitting, hold the radio in a vertical position with its microphone 1 inch (2.5 cm) away from your mouth and keep the antenna at least 1 inch (2.5 cm) away from your head. Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 WARNING! IC RSS GENERAL REQUIREMENT ENGLISH This device complies with Industry Canada’s license-exempt RSSs. Operation. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 WARNING! IC RSS GENERAL REQUIREMENT FRENCH Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 BEFORE YOU BEGIN Battery Pack Installation and Removal Battery Charging To install the battery pack, align the battery pack to the radio with an offset about 1/2 inch (1.5 cm) from the top edge of battery compartment, then slide the battery pack upward until it locks in place with a “Click.” Remove the Spacer Plate from the nest of the optional CD-58 Desktop Charger, if the Battery Spacer is installed.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 BEFORE YOU BEGIN the left side when viewing the charger from the front. If the battery pack is inserted correctly, the LED indicator will glow red. A fully-discharged battery pack will charge completely in 1.5 - 4.5 hours (depending on the battery pack being charged). When charging is completed, the LED indicator will change to green.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 BEFORE YOU BEGIN Belt Clip Installation and Removal MIC/SP CAP Installation To install the Belt Clip: align the Belt Clip to the groove of the Battery pack, then press the Belt Clip downward until it locks in place with a “Click.” Install the MIC/SP cap with the supplied screws.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 CONTROLS & CONNECTORS CH (Channel) Selector VOL (Volume)/PWR (Power) Knob LED Indicator (Programmable) Antenna Jack Default settings are: Steady Red: Transmitting in progress Blinking Green: Busy Channel Steady Green: Tone Squelch in defeated condition Blinking Red: Low Battery Power PTT Switch MIC/SP Jack (External MIC/SP) SIDE-1 Button SIDE-2 Button Speaker 10 Battery Pack Latch Microphone EVX-261 OPERATING MANUAL Vertex Stan
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 OPERATION Preliminary Steps Operation Quick Start Install a charged battery pack onto the transceiver, as described previously. Screw the supplied antenna onto the Antenna jack. It is not recommended to operate this transceiver without an antenna connected. If you have a Speaker/Microphone, we recommend that it not be connected until you are familiar with the basic operation of the EVX-261.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 OPERATION noise and resume normal (quiet) monitoring. To transmit, monitor the channel and make sure it is clear. Press and hold the PTT switch. Speak into the microphone area of the front panel grille in a normal voice level. To return to the Receive mode, release the PTT switch.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 OPERATION to two simultaneous transmissions. The second mode is Direct mode, which enables two communications paths on a single frequency, doubling your capacity with only the subscriber radios. No repeater is necessary when operating in Direct mode. If the BCLO (Busy Channel Lockout) feature has been programmed on an analog channel, the radio will not transmit when a carrier is present.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 OPERATION Remote Monitor: A priority radio can force another radio in the fleet to open transmission for a pre-programmed period with the CE156 software for the priority radio to hear any audio on the radio being monitored. For further details, contact your Vertex Standard dealer. Note: The EVX-261 cannot control other radio by the above features (decode only).
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 ADVANCED OPERATION Programmable Key Functions The EVX-261 provides two Programmable Function (PF) keys: SIDE-1 and SIDE-2 keys. Both PF keys can be customized, via programming by your Vertex Standard dealer, to meet your communications/network requirements. The possible PF key programming features are illustrated at the right, and their functions are explained in more detail in the next pages.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 ADVANCED OPERATION Description of Operating Functions All functions listed in this section can be assigned to any PF Key. Up to two functions can be assigned per key, with the feature being activated by: Short Press (SP) - Press and release Long Press (LP) - Press and hold MONITOR Any signaling features can be activated/deactivated by an assigned PF key. The LED indicator will glow green when the signaling feature is deactivated.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 ADVANCED OPERATION VOX ANTI-TRIP SCAN VOX Anti-trip prevents the transceiver from activating a VOX transmission from either internal or external radio alert tones (radio beeps). The Scanning feature is used to monitor multiple channels programmed into the transceiver. When scanning, the transceiver will check each channel for the presence of a signal and will stop on a channel if a signal is present.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 ADVANCED OPERATION To stop Dual Watch: Press, (or press and hold), the assigned PF key to disable the Dual Watch feature. The radio receives the channel which was selected by the CH Selector knob. When operating on a duplex channel system (for example, a repeater station), TA Scan allows the transceiver to search both transmit and receive frequencies on your duplex system.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 ADVANCED OPERATION Note that your dealer may have mode provision for “Talk Around” channels by programming “repeater” and “Talk Around” frequencies on two adjacent channels. If so, the key may be used for one of the other Pre-Programmed Functions. RESET When operating in the selective call feature, resets the communication by an assigned PF key. CALL Send a pre-programmed 2 Tone call signal with a one touch PF key.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 LOCK ARTS™ (AUTO RANGE TRANSPOND SYSTEM) In order to prevent accidental channel changes or inadvertent transmissions, various aspects of the CH Selector knob, Programmable keys, and PTT switch may be locked. The precise lockout configuration is programmed by your Authorized Vertex Standard dealer.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 OPTIONAL ACCESSORIES FNB-V133LI-UNI FNB-V134LI-UNI FNB-V136-UNI CD-58 PA-55 VAC-UNI VAC-6058 MH-37A4B-1 MH-66A4B MH-100 MH-101A4B MH-102A4B MH-103A4B MH-201A4B MH-360S MH-450S VH-150A VH-150B VCM-5 7.4V DC , 1380 mAh Li-Ion Battery Pack 7.4V DC , 2300 mAh Li-Ion Battery Pack 7.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 WARRANTY POLICY Vertex Standard warrants, to the original purchaser only, its Vertex Standard manufactured communications products against defects in materials and workmanship under normal use and service for a given period of time from the date of purchase. Limited Warranty Details: North America customers (USA and Canada): http://www.vertexstandard.com/lmr/warranty-terms.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 NOTE EVX-261 OPERATING MANUAL 23 Vertex Standard LMR, Inc.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 NOTE 24 EVX-261 OPERATING MANUAL Vertex Standard LMR, Inc.
Exhibit 8: Operating Manual FCC ID: AXI11374720 IC: 10239A-11374720 The AMBE+2™ voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment.
Exhibit 8: Operating Manual No portion of this manual may be reproduced without the permission of Vertex Standard LMR, Inc. FCC ID: AXI11374720 IC: 10239A-11374720 Vertex Standard LMR, Inc. 4-6-8 Shibaura, Minato-ku, Tokyo 108-0023, Japan Vertex Standard is a trademark of Vertex Standard LMR, Inc. All other trademarks are the property of their respective owners. ©2016 Vertex Standard LMR, Inc. All rights reserved. Vertex Standard LMR, Inc.