FCC ID: AXI11133020 IC: 10239A-11133020 EVX-531 Operating Manual Programmable Functions/Features IP57 Submersible (1 m/30 min.
FCC ID: AXI11133020 IC: 10239A-11133020 Contents Introduction...............................................................1 Warning! FCC RF Exposure Requirements...........2 Before You Begin.......................................................4 Battery Pack Installation and Removal................4 Battery Charging...................................................4 Low Battery Indication.........................................5 Belt Clip Installation and Removal......................
FCC ID: AXI11133020 IC: 10239A-11133020 Introduction The EVX-531 is full-featured Hand-Held Digital/Analog Transceiver designed for business communications in the VHF/UHF Land Mobile bands. This transceiver is designed for reliable business communications in a wide variety of applications with a wide range of operating capability provided by their leading-edge design. The EVX-531 allows to 32-channel capacity and 2 groups.
FCC ID: AXI11133020 IC: 10239A-11133020 Warning! FCC RF Exposure Requirements This Radio has been tested and complies with the Federal Communications Commission (FCC) RF exposure limits for Occupational Use/Controlled exposure environment. In addition, it complies with the following Standards and Guidelines: FCC 96-326, Guidelines for Evaluating the Environmental Effects of Radio-Frequency Radiation.
FCC ID: AXI11133020 IC: 10239A-11133020 Warning! FCC RF Exposure Requirements When transmitting, hold the radio in a vertical position with its microphone 2 inches (5 cm) away from your mouth and keep the antenna at least 2 inches (5 cm) away from your head and body. The radio must be used with a maximum operating duty cycle not exceeding 50%, in typical Push-toTalk configurations. DO NOT transmit for more than 50% of total radio use time (50% duty cycle).
FCC ID: AXI11133020 IC: 10239A-11133020 Before You Begin Battery Pack Installation and Removal To install the battery pack, align the battery pack to the radio with an offset about 1/2 inch (1.5 cm) from the top edge of battery compartment, then slide the battery pack upward until it locks in place with a “Click.” To remove the battery, turn the radio off and remove any protective cases.
FCC ID: AXI11133020 IC: 10239A-11133020 Before You Begin proper positioning of the battery pack. If charging with the transceiver attached, turn the transceiver off. The antenna jack should be at the left side when viewing the charger from the front. If the battery pack is inserted correctly, the LED indicator will glow red. A fully-discharged battery pack will charge completely in 1.5 - 3.0 hours (depending on the battery pack being charged).
FCC ID: AXI11133020 IC: 10239A-11133020 Before You Begin Belt Clip Installation and Removal To install the Belt Clip: align the Belt Clip to the groove of the Battery pack, then press the Belt Clip downward until it locks in place with a “Click.” To remove the Belt Clip: use a flat head screw driver to press the Belt Clip Tab away from the battery pack to unlock the Belt Clip, then slide the Belt Clip upward to remove it.
FCC ID: AXI11133020 IC: 10239A-11133020 Controls & Connectors VOL/PWR Knob CH (Channel) Selector Antenna Jack 3 TOP SEL Key LED Indicator (Programmable) Default settings are: Steady Red: Transmitting in progress (Analog) Steady Blue: Transmitting in progress (Digital) Blinking Green: Busy Channel Steady Green: Tone Squelch in defeated condition PTT Switch MIC/SP Jack (External MIC/SP) SIDE-1 Button SIDE-2 Button Speaker EVX-531 Operating Manual Battery Pack Latch Microphone 7
FCC ID: AXI11133020 IC: 10239A-11133020 Preliminary Steps Operation Install a charged battery pack onto the transceiver, as described previously. Screw the supplied antenna onto the Antenna jack. Never attempt to operate this transceiver without an antenna connected. If you have a Speaker/Mi crophone, we recommend that it not be connected until you are familiar with the basic operation of the EVX-531.
FCC ID: AXI11133020 IC: 10239A-11133020 Operation EVX-531 Operating Manual To transmit, monitor the channel and make sure it is clear. Press and hold the PTT switch. Speak into the microphone area of the front panel grille in a normal voice level. To return to the Receive mode, release the PTT switch. Press the (Orange) TOP SEL key or SIDE-2 button to activate one of the pre programmed functions which may have been enabled at the time of programming by the dealer.
FCC ID: AXI11133020 IC: 10239A-11133020 Operation If a Speaker/Microphone is available, remove the plastic cap and its two mounting screws from the right side of the transceiver, then align t h e c o n n e c t o r o f t h e VX-200 Speaker/Microphone on the radio; secure the connector pin using the screws supplied with the Speaker/Microphone. Hold the speaker grille up next to your ear while receiving.
FCC ID: AXI11133020 IC: 10239A-11133020 Advanced Operation Programmable Key Functions The EVX-531 provides the programmable TOP SEL, SIDE-1, and SIDE-2 function keys. These Programmable Function keys can be customized, via programming by your Vertex Standard dealer, to meet your communications/network requirements. The possible Programmable key programming features are illustrated on the next page, and their functions are explained beginning after page 13.
FCC ID: AXI11133020 IC: 10239A-11133020 Advanced Operation Function None Monitor Monitor -MomentarilyLow Power Privacy SQL OFF SQL OFF -MomentarilyBeep Off Whisper VOX CH Announcement VOX Anti-Trip Emergency Lone Worker Group Change PRI-2 PRI-2 Set 12 Programmable Key (Press Key / Press and Hold Key) TOP SEL SIDE-1 SIDE-2 / / / / / / /--/--/--/ / / / / / / / / /--/--/--/ / / / / / / / / / / / / / / /--/--/--/ / / / / / / / / / / / Function PRI-2 Disable Scan Group Scan Dual Watch FM Scan (Follow-Me Scan
FCC ID: AXI11133020 IC: 10239A-11133020 Advanced Operation Description of Operating Functions Monitor SQL OFF Monitor -Momentarily- SQL OFF -Momentarily- Low Power key. Press (or press and hold) the assigned Programmable key to cancel any signaling features; the LED indicator will glow green. Cancel any signaling features while pressing the assigned programmable key. Press (or press and hold) the assigned programmable key to open the SQL to hear background noise (unmute the audio).
FCC ID: AXI11133020 IC: 10239A-11133020 VOX Advanced Operation Press (or press and hold) the assigned programmable key to turn the VOX function “On” or “Off”. You may disable the VOX function temporarily by pressing the PTT switch. VOX Anti-Trip Press (or press and hold) the assigned Programmable key to toggle the VOX Anti-Trip feature “On” and “Off”. When the VOX Anti-Trip feature is set to “On”, the transceiver does not activate the transmitter section from the receiver audio and own beep sound.
FCC ID: AXI11133020 IC: 10239A-11133020 PRI-2 Set Advanced Operation Press (or press and hold) the assigned programmable key to toggle the current channel to the priority channel 2 “enable” and “disable”. PRI-2 Disable Press (or press and hold) the assigned programmable key to disable the priority channel 2 of the group temporarily. Scan The Scanning feature is used to monitor multiple signals programmed into the transceiver.
FCC ID: AXI11133020 IC: 10239A-11133020 Group Scan Advanced Operation The Scanning feature is used to monitor multiple channels programmed into the transceiver. While scanning, the transceiver will check each channel of the programmed group for the presence of the signal, and will stop on a channel if a signal is present. Press (or press and hold) the assigned programmable key to activate the scanning on the selected groups.
FCC ID: AXI11133020 IC: 10239A-11133020 TA Scan Advanced Operation Press (or press and hold) the assigned Programmable key to toggle the TA (Talk Around) scan feature “On” and “Off”. While TA scan is proceeding, the transceiver will search both the transmit and receive frequencies. When a signal is encountered on the receive frequency, the EVX-531 will pause until the signal disappears.
FCC ID: AXI11133020 IC: 10239A-11133020 Call 1 to Call 3 Advanced Operation Press (or press and hold) the assigned Programmable key to send a 2-tone sequential tone group which is pre-defined. Speed Dial Press (or press and hold) the assigned Programmable key to prepare the Speed Dial function. Press the PTT switch within 5 seconds of releasing the key to send a DTMF tone which is pre-defined. Call Press (or press and hold) the assigned programmable key to send a 2-tone sequential tone.
FCC ID: AXI11133020 IC: 10239A-11133020 LOCK In order to prevent accidental channel change or inadvertent transmission, various aspects of the CH Selector knob, Programmable keys, and PTT switch may be locked. The precise lockout configuration is programmed by your Dealer. To locked out the key locking, turn the radio off. Now, press and hold the PTT and SIDE-2 key while turning the radio on again. To cancel locking, repeat this process.
FCC ID: AXI11133020 IC: 10239A-11133020 FNB-V133LI FNB-V134LI CD-58 PA-51 MH-66A4B MH-81A4B ATU-16B ATU-16C ATU-16D ATU-16F CSS450 CLIP-20 CE142 FIF-12 CT-106 CT-27 20 Optional Accessories 7.4V, 1380 mAh Li-Ion Battery Pack 7.
FCC ID: AXI11133020 IC: 10239A-11133020 The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment.
FCC ID: AXI11133020 IC: 10239A-11133020 Vertex Standard LMR, Inc. Copyright 2012 Vertex Standard LMR, Inc. All rights reserved. No portion of this manual may be reproduced without the permission of Vertex Standard LMR, Inc.