Install Instructions

1.
2.
3.
4.
5.
6.
7.
Testing
From the Installer Toolbox, select walk test.
To test the disarm button, hold the button down for 2
seconds. This disarms the Control Panel as well as the doors,
windows, and motion detectors.
To test the away button, hold the button down for 2
seconds. This arms the Control Panel as well as the doors
and windows (in Away mode).
To test the stay button, hold the button down for 2
seconds. This arms the Control Panel as well as the doors
and windows (in Stay mode).
To test the Auxiliary button (if previously programmed,
this button can trigger a pre-selected output).
To test the Away and Disarm buttons (if the emergency key
was programmed in step 6 above), pressing both the Away
and Disarm buttons at the same time for 5 seconds sends
one of four types of emergency signals:
(1) silent panic (2) audible alarm (3) silent panic (4) fire
Exit the Installer Toolbox.
Inserting & Replacing
Batteries continued...
Replace only with the same or
equivalent type of battery as
recommended by the
manufacturer. See
specifications. Batteries must
not be recharged,
disassembled or disposed of in
fire. Disposal of used batteries
must be made in accordance
with the waste recovery and
recycling regulations in your
area. Keep away from small
children. If batteries are
swallowed, promptly seek
medical attention.
California Only: This Perchlorate
warning applies only to
Manganese Dioxide Lithium cells
sold or distributed ONLY in /
California, U.S.A. Perchlorate
Material‐special handling may
apply. See dtsc.ca.gov/hazard-
ouswaste/perchlorate.
•
•
•
•
•
•
•
Arm the system (doors, windows, and motion sensors).
Arm the system with no entry delay (if programmed).
Disarm the system.
Trigger panic alarms.
Turn system‐controlled lights on or o (via the open collector
output)
Other open collector output functions (if applicable)
Use with the GE Alarm System to open a garage door. See the
GE install instructions.
GE Keyfob Manual
Installation Instructions
The Versa KeyfobG is a 4‐button key ring remote. The KeyfobG enables you
to turn the GE system on and off before entering the home or after exiting. If
there is an emergency, you can turn on the siren and automatically call the
central monitoring station. If lamp modules have been installed, you can use
the key fob to turn all system‐controlled lights on or off via the open
collector output. Use with the GE Alarm System to open a garage door. The
KeyfobG is a lithium coin battery‐powered, wireless key fob designed to fit
on a keychain, in a pocket, or in a purse. It provides a convenient option for
the following system operations:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Programming
The following steps are for programming (learning) the sensor Versa
KeyfobG into the GE control panel. Scroll between options using the ←
and → arrows. Move to the previous or next prompt by pressing the ↑
and ↓ arrows.
Go to Q3: Select fob # (1 to 8).
Fob used (0 to 1) or Fob enabled (0 to 1).
(0) unused (1) used (0) disabled (1) enabled
Select RF sensor equipment code. Enter 0866 for the Versa
Key 4‐button key ring remote.
Enter RF sensor serial number (7 digits).
Manual Entry: Type in the last 7 digits of the TX ID that is found
outside of the box or on the back of the device.
Auto Entry: With the panel in learn‐in mode (press Shift then
Learn). The correct TX ID should appear. Accept the correct TX ID
by pressing OK. Remember to press the ↓ arrow to continue going
through the 2GIG system configuration prompts.
Select RF sensor equipment age (0 to 1).
(0) new (product is new) (1) existing (product already exists)
Select fob emergency key (0 to 4).
(0) disabled (1) auxiliary alarm (2) audible alarm (3) silent panic
(4) fire
Select fob key 2 can disarm (0 to 1).
(0) disabled (1) enabled
Construct RF sensor voice descriptor.
Press Insert then press any number between 002 and 255 to add a
word. For example, if you wanted to name this key ring remote as
“main key remote,” press Insert then press 138 for MAIN. Press
Insert then press 121 for KEY. Press Insert then press 183 for
Remote.
Select fob arm no delay (0 to 1).
(0) disabled (1) enabled
Select fob key 4 output (0 to 2).
(0) disabled (1) toggle output (2) momentary output
To program another sensor click next.
To exit programming, click skip then end and exit. Upon exit,
the panel takes a several seconds to reboot.
Tip: Each key fob that is learned in uses one of the available fob sensor
numbers as programmed in step 1.
WARNING: The polarity of the battery must be observed, as shown.
Improper handling of lithium batteries may result in heat generation,
explosion or fire, resulting in personal injuries.
Continued >
Inserting & Replacing Batteries
Away
Disarm
Stay
Auxiliary
this device may not cause interference, and
this device must accept any interference, including interference
that may cause undesired operation of the device¹.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT
This device comples with FCC Rules Part 15. Operation is subject to the
following two conditions:
1.
2.
FCC Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC Notice