Install Guide BH61 Wireless Alarm Hub Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 sales@verkada.com All specifications are subject to change without notice Copyright © Verkada Inc. All rights reserved.
Document Document Details V1.0 (20210929) (V1.0 first published 20210929) Firmware Firmware version can be verified on Verkada Command command.verkada.com. 2 Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 sales@verkada.com All specifications are subject to change without notice Copyright © Verkada Inc. All rights reserved.
Introduction What’s in the box BH61 Wireless Alarm Hub 3 M4 x 50mm machine screws, wing nuts, and washers Mount plate (Attached to hub) 4 M4 x 25mm PH2 wall screws ● ● ● ● ● T10 Security Torx screwdriver Connect What you’ll need ● ● 4 wall anchors Mounting template A working Internet connection 802.3af / 802.3at POE Power over Ethernet (PoE) switch, or a PoE injector* A smartphone or laptop A Phillips screwdriver or power drill with a Phillips driver bit ¼ inch (6.
Introduction Sensor overview LED Placement LED Behavior To ensure a reliable connection with your sensors, mount the BH61 Wireless Alarm Hub in a location that minimizes the number of walls and other obstructions between the hub and the wireless sensors. Solid Orange Hub is on and booting up. Flashing Orange Hub is updating firmware. Flashing Blue Hub can receive events, but cannot reach the server Solid Blue Hub is running, connected, and receiving events. 4 Verkada Inc.
Installation Connect 1/1 Use the provided T10 Torx security screwdriver to loosen the screws and lift the top cover off the hub. Connect the hub to an 802.3af/at Power over Ethernet port on your network. Please note: Your BH61 Wireless Alarm Hub includes an integrated backup battery. The Hub must be connected for eight hours before the battery is fully charged. For easy registration and setup, scan the QR code on the product. If you prefer to manually register your product, please proceed to: verkada.
Installation Mounting 1/2 To remove the mount plate, loosen the mount plate screws and twist the device counterclockwise. Lift the device vertically off the base plate and set aside Use the provided mounting template to mark wall mount holes. For a junction box mount, use the mounting template to determine the correct hole pattern. For a solid material like wood or metal, drill ⅛ inch pilot holes. Drive mounting screws directly into the pilot holes. 6 For drywall, drill ¼ inch holes.
Installation Mounting 2/2 Place the hub over the mount plate screws and twist clockwise. Tighten the mount plate screws with a Phillips screwdriver. Replace the hub cover and secure it using the provided T10 Torx security screwdriver. 7 Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 sales@verkada.com All specifications are subject to change without notice Copyright © Verkada Inc. All rights reserved.
Appendix BH61 Compliance FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix BH61 Compliance Caution 1. 2. 3. 4. 5. 6. 9 Maintenance and repair work must always be carried out by qualified technical personnel. Disconnect power from the unit when performing a maintenance task. Wiring methods used for the connection of the equipment to earth shall be in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part 1, CSA C22.1.
Appendix Support Thank you for purchasing this Verkada product. If for any reason things don’t work right, or you need assistance, please contact us immediately. verkada.com/support Sincerely, The Verkada Team 10 Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401 sales@verkada.com All specifications are subject to change without notice Copyright © Verkada Inc. All rights reserved.