Verizon LTE UE Tester Model: INTTP20213425 Quick Installation Guide Manufacture By: Sercomm Corporation 8F, No. 3-1, YuanQu Street, Nankang, Taipei 115, Taiwan, R.O.C.
Table of Contents CHAPTER 1 INTRODUCTION .............................................................................................. 1 Package Contents .............................................................................................................. 1 Key Feature ........................................................................................................................ 1 LEDs ........................................................................................................
Chapter 1 Introduction 1 This Chapter provides an overview of the device's features and capabilities. The LTE INTTP20213425 series UE Tester is a Desktop Small Cell LTE Device Tester handles multiple scenarios, running different protocols simultaneously, and provides a complete, independent solution. Package Contents The following items should be included: If any of the above items are damaged or missing, please contact your dealer immediately.
LEDs Top-mounted LED POWER (Red) On - Power On/Normal Operation Off - Power off WAN1 (Red/Green) On Green - CPU1 LAN active On Red - CPU1 LAN inactive WAN2 (Red/Green) On Green – CPU2 LAN active On Red – CPU2 LAN inactive RF1 (Red/Green) On Green – Band RF1 in service On Red – Band RF2 RF not in service RF2 (Red/Green) On Green – Band RF2 in service On Red – Band RF2 RF not in service RF3 (Red/Green) On Green – Band RF3 in service On Red – Band RF3 RF not in service RF4 (Red/Green) On Green –
Rear Panel Power Input: 12 Vdc, 9A, Power Jack to Power Adaptor Reset 1 This button is used to reset or restore to factory default for CPU1 Reset 2 This button is used to reset or restore to factory default for CPU1 Ethernet Use standard LAN cable (RJ45 connectors) to connect to backhaul /broadband router RF1 Band SMA connection for Band RF1 External Antennas RF2 Band SMA connection for Band RF2 External Antennas RF3 Band SMA connection for Band RF3 External Antennas RF4 Band SMA connection
Chapter 2 Initial Installation 2 This Chapter covers the software installation of the device. Procedure 1. External Antenna Connect the external antennas (total 8 included in the package) to antenna connector ports. 2. Power Up Connect the supplied power adapter to the UE Tester. Use only the power adapter provided. Using a different one may cause hardware damage. 3. Connect LAN Cable Use a standard LAN cable to connect the device to the Ethernet port on the UE Tester and to LAN/PC 4.
Chapter 3 Specifications 3 General Specification Connectivity - 10x SMA RF connector for External Antennas - Four Gigabit Ethernet LAN ports Power Supply External Power Adapter: Input: AC100~240V~1.6A, 50Hz/60Hz, Altitude 0 to 5000 Meters Output: 12 Vdc, 9A Operating Requirement Operating Temp. 0ºC to 40ºC Storage Temp. -5ºC to 45ºC Operating Humidity 5% to 90% Non-Condensing Storage Humidity 5% to 95% Non-Condensing Reset button Two LED 9 LED for Status.
Regulatory Requirements 類別 Area Standard EMC USA FCC Part 15B RF USA FCC Part 24E/27/22H/27F Note FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Safety Information All instructions, warning and caution statements that accompany this equipment must be strictly followed at all times to ensure its safe use. Observe all warning and caution symbols that are fixed to this equipment. This electrical equipment is designed with the utmost care for the safety of those who install and use it.
At least one other trained person must be in attendance, who can immediately and safely disconnect the system if necessary. This second person must be trained in first aid for emergency purposes Some parts of all electrical installations are energized. Failure to follow safe work Practices and the safety warnings may lead to bodily injury and property damage.
Device Surface Cleaning You may clean the device case using a cloth dampened with mild liquid detergent (such as Dawn) and water. Always unplug/disconnect power before apply any cleaning to 13245 UE Tester.
Accessories Item Description P/N AC/DC Adapter (without power core) AC100~240V~1.