Model: VF01
Dear Customer, Thank you for purchasing the Verilux Original Natural Spectrum® Floor Lamp. You have received a quality product, backed by a one year limited warranty. As a Verilux customer, your satisfaction means everything to us. We look forward to serving you now and in the future. Many other healthy lighting products are available through our catalog and online. Visit us on the web at www.verilux.
READ ALL INSTRUCTIONS BEFORE USING Important Safeguards DANGER: • Do not operate this lamp near a water source to avoid electrocution. WARNING: • Do NOT dismantle. • Do not use with power supply voltage other than 120 VAC. • Do not operate lamp in close proximity to flammable or combustible vapors, such as aerosol spray products, or where oxygen is being administered. • Do not cut or shorten the power cord.
VEUILLEZ LIRE L’INTÉGRALITÉ DES INSTRUCTIONS AVANT TOUTE UTILISATION Mesures de sécurité importantes DANGER : • N’utilisez pas cet appareil à proximité d’une arrivée d’eau pour éviter tout risque d’électrocution. AVERTISSEMENT : • Avant de brancher la lampe, vérifier que la tension de la prise murale ne dépasse pas 120 volts. • Ne PAS utiliser de produit lubrifiant lors de l’assemblage; voir la section de dépannage en cas de difficulté lors de l’assemblage de la lampe.
Getting Started Main Parts & Controls A. B. C. D. E. F. G. H. I. Lamp Head Gooseneck Shaft Lamp Base Power Cord Polarized Plug Parabolic Grid Diffuser Bulb High/Off/Low Switch Close-up of Lamp Head B A H G I C E D F CAUTION: DO NOT LIFT THE LAMP BY THE GOOSENECK. THE LAMP SHOULD BE LIFTED BY THE SHAFT. MISE EN GARDE : NE PAS SOULEVER LA LAMPE PAR SON COL-DE-CYGNE. LA LAMPE DOIT ÊTRE SOULEVÉE PAR LA TIGE.
Unpacking Your Lamp 1. Remove all pieces from box. Locate 2 Phillips head screws. 2. Detach red plastic pieces and store them in the event you need to return the lamp. 3. Important: To avoid scratching the metal shaft, do not use a sharp object to cut the plastic covering. The clear plastic covering on the shaft is specially designed to tear away easily. IMPORTANT NOTE: Remove red plastic protective pieces prior to assembly.
Assembly Instructions Read Instructions Carefully Before Assembly: 1. Connect the two ends of the Power Cord (between the Base and the Shaft) using the lock connectors. 2. Carefully tuck excess Power Cord into the Shaft. WARNING: DO NOT CUT OR SHORTEN THE POWER CORD. 3. Insert the Gooseneck and the Shaft into the Base. Fig. 1 4. Check direction of the lamp and the hole on the Base, then use a Phillips Head Screwdriver (not included) to tighten the screw into the hole.
Assembly Instructions — continued 5. To prevent damage during shipping, the Verilux bulb is surrounded by protective padding. Carefully remove and dispose of the protective padding. Check to ensure that the bulb is fully seated and has not come loose from the socket during shipping. There should be no gap between the bulb and socket. 6.
Bulb Replacement Instructions Installation 1. Unplug lamp from power source. C 2. Firmly hold base (B) and push bulb (C) into the socket (A). 3. Be sure bulb is firmly seated in the socket (see below) and snapped into the metal bulb clip (D). A 4. Replace grid diffuser. B Removal C 1. Unplug lamp from power source. 2. To access the bulb, remove grid diffuser by depressing the tab and lifting it out (see page 8). 3. Firmly hold bulb base (B) and pull bulb (C) from the socket (A) in an outward motion.
Troubleshooting Before requesting service on your Verilux® lamp, please read the following: • Make sure all power connectors, cords and plugs are inserted fully and securely. • Be sure the bulb is securely seated into the socket (see page 9). • Make sure there is power to the wall outlet or try another outlet. CAUTION: Disconnect lamp before performing alignment activity. MISE EN GARDE : DÉBRANCHER LA LAMPE AVANT D’EFFECTUER SON ALIGNEMENT.
Care & Cleaning Your lamp is made from high quality materials that will last for many years with minimum care. You may want to periodically clean the lamp, using a mild non-abrasive cleaner and soft cloth. When cleaning, make sure you have turned off and unplugged the unit, and allowed sufficient time for the unit to cool. All liquid should be properly wiped away and dried prior to restoring power. CAUTION: DO NOT USE SOLVENTS OR CLEANERS CONTAINING ABRASIVES, OR AMMONIA BASED CLEANERS ON THIS PRODUCT.
One Year Limited Warranty ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED FOR REPAIR OR REPLACEMENT! Many questions may be answered by visiting www.verilux.com, or you may call our Customer Service Department at 1-800-786-6850 during normal business hours. This limited warranty is provided by: Verilux, Inc.