User's Manual
095208 Wireless Optical Mouse User
Manual
Welcome
Thank you for selecting this
product! This mouse is one kind of
newly developed wireless serials
mice in our company, and it uses the
global-used frequency of 27MHz.
The comfortable and perfect shape is
designed according to somatology.
With it, You can get rid of the
bondage of wires and enjoy your
beautiful life from the high
technology.
Product Features
1. Radio frequency 27MHz,It has
256 ID code, there is no
interference even many mice
being used at the same time.
2. With receiver hidden inside
and the whole design looks
more ntimate and scientific.
3. Automatically save power
sleeping functions, battery life
be prolonged.
4. With charge and regular circuit,
it can use the attached
retraceable line to charge for
the mouse. Even if there is no
battery in the mouse, you can
use the mouse directly, thus it
resolve the problem of lack
the battery.
Systems Compatibility
IBM PC and Windows
Me/2000/XP
Push Receiver
Dig it with finger from the
push side then the receiver
is emerged.( Please see the
picture)
The Steps of Install Emitter Battery
1. Please prepare for two new
AAA chargeable batteries and
take 2. the battery cover
( please see the picture)
Please insert the batteries
correctly according to the
polarity marks of the battery
grooves., And Install the battery
cover.
Receiver Installation
1. We suggest that you use the
prolonged cable and place
the receiver on your desk,
which is good for you to get
better work capability.
2. If you use PS/2 connector,
please use the USB to PS/2
adaptor and connect with
the connector before your
computer start-up.
3. For laptop, you may connect
the receiver directly with the
USB connector.
ID Setup
1. Please move the mouse near
to the receiver
2. Press the ID button of the
receiver by your hand, the
receiver light begin to flash.
Press the ID button of the
mouse bottom with some hard
and acuate object within 10
seconds, the receiver light will
flash very fast, a few seconds
later it will be on which shows
it is successfully to finish the
digital transmission between
the mouse and the receiver.
You may start to use it.
3. Working distance: within
0.8-1.5 meters.
Charge Function
When using mouse, if the red
led of the low battery beside the
wheel flashes, please change
batteries or charge them. The mouse
can use USB line to charge, connect
one side of USB line to the connector
of the board, and the other side to
USB connector before the mouse,
thus it can successfully charge the
battery. It can charge while you use
the mouse. It is full within about 3-4
hours, and then unplug the connector
to stop the charge. Please note that
the time of charge may vary when the
degree of discharge is different.
Attention Please
1. Please don’t make the mouse
far away from the receiver in
order to work more smoothly.
2. You’d better use the mouse on
the white desk, in this way the
batteries can be used longer
time. Please remove the
batteries if the mouse will not
be used for a long time or if
you travel outside.
3. This mouse with save power
sleeping functions, please
press any key or scroll the
wheel to wake up the mouse
when it is sleeping.
4. If you want to take off the
mouse power,please continue
to press the ID switch of the
mouse bottom over 3 secons.If
you want to take on the
power,please click the ID
switch once again.
5. The optical mouse will not
work freely on a smooth
desk ,glass, any reflecting
surface, 3D mouse pad.
6. When you move the mouse, if
the light of the battery before
the receiver flashes, which
shows that the power is nearly
finished. Please change the
proper-sized new battery or
charge it immediately.
7. You can place the receiver in
the mouse when you want to
carry the mouse on business,
and press the switch of ID for a
long time so as to switch off
the power.
Caution
Any changes or modifications
not expressly approved by the
party responsible for
compliance could void the
user's authority to operate the
equipment.
Note
Note: This equipment has
been tested and found to
comply with the limits for a
Class B digital device,
pursuant to part 15 of the FCC
Rules. These limits are
designed to provide
reasonable protection against
harmful interference in a
residential installation. This
equipment generates, uses
and can radiate radio
frequency energy and, if not
installed and used in
accordance with the
instructions, may cause
harmful interfer- ence to radio
communications. However,
there is no guarantee that
interference will not occur in a
particular installation. If this
equipment does cause
harmful interference to radio
or television reception, which
can be determined by turning
the equipment off and on, the
user is encouraged to try to
correct the interference by one
or more of the following
measures:
--Reorient or relocate the
receiving antenna.
--Increase the separation
between the equipment and receiver.
--Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
--Consult the dealer or an
experienced radio/TV
technician for help.
This device complies with Part 15
of the FCC Rules. Operation is
subject to the following two
conditions: (1) this device may
not cause harmful interference,
and (2) this device must accept
any interference received,
including interference that may
cause undesired operation.