OPERATION Preparing for Use {. Place the HEADSET on the BASE UNIT for 12 hours of charging. 2. After] hours, remove the HEADSET from the BASE UNIT. Placing a Cali Using the HEADSET: f. Press the [TALK] button on the HEADSET. The HEADSET JN USE indicator and the BASE UNIT IN USE/CHARGE indicator will light up. Or rotate downward the microphone arm to activate the auto hook-up system on the HEADSET. 2. Listen for a dial tone. 3. Diophantine number, Using the BASE UNIT: I.
[I Ending a Cali — Using the HEADSET. I. Since the unit features “Auto-Standby”, return the HEADSET to the BASE UNIT OR press the [TALK] button CR just rotate the microphone arm backward to the vertical position up when you are away from the BASE UNIT. Using the BASE UNIT. i. Press the [SP-PHONE] button to hang up. Last Number Redial 1. If you ger a busy signal, use the Redial function to automatically dial the fast phone number died (up to 32 digits). Redial Using the HEADSET I.
Channel Selection Channel Scan (Auto scan! If you are reeving a call or dialing out and [TALK] is pressed, the unit auto scans for the best channel available. Channel Scan (Manual) If the existing channel becomes noisy or starts having interference, press the [SCAN] button on the HEADSET. The unit will automatically scan for the best channel available. NOTE: It takes about 2 seconds for the unit to scan to the next channel. Intercom Function Activating the Intercom using the BASE UNIT I.
If the BASE UNIT user wants to access the telephone call while in the intercom mode, press the [SP-Buttonhole. A three-way conversation is established. 1 the HEADSET user does not want to share in the conversation between the BASE UNIT user and the third party, press the [TALK] button on the HEADSET. The HEADSET will be disconnected.
EXAMPLE: To store the number 611-4834 under the index number 1 on the keypad: Press the [MEMO] button. Dial 611-4834. Press the [MEMO] Burton again. Press | on the keypad. You have stored 611-4834 under key | on the keypad Recalling Stored Numbers from Memory if the HEADSET is used to recall a phone number Press the [TALK] button. Press the [MEMO] button. Press the index number for the number you have stored. The stored number will be dialed automatically.
Security System Your cordless telephone uses a digital security coding system ta prevent unauthorized use of your telephone line by another nearby cordless telephone. The system has its awn identifying signal created by microprocessors in both the BASE UNIT and HEADSET. Security Code This telephone has an internal security code with 65,536 possible combinations, Each time you pick up the HEADSET, the code is randomly set to a new combination.
CARE AND MAINTENANCE Your cordless headset telephone has been designed to give years of trouble free electromagnetically service, To assure it's longevity, please read the following maintenance instructions. I Keep your telephone away from heat as high temperatures can shorten the fife of the electrical components and distort or melt it's plastic parts, Keep your telephone free of dust and moisture. IF it gets wet, wipe it dry immediately. Liquids can contain minerals that can corrode electronic circuits.
RECHARGING THE Ei" ' Battery Type Use the following type and size battery pac: 5Y, & Ni-MG Battery Pack: GPI GP6OAAAHIBML Nigh Recharging the Battery Pack The nickel metathesis (Ni-MG) battery pack in the HEADSET cane recharged many times using the built-n charger in the BASE UNIT. ‘When the battery packs low, a beep"sourid wil be heard every seconds and the IN BATHHOUSE LOW LED indicator wil blink rapidly. This indicates that recharging the battery pack will be necessary.
DOUBLE SHOOTING : Problem Solving Section For your assistance, we have listed below a few common problems. Phone does not work, check the following: I. BASE UNIT is plugged into power source. 2. HEADSET is charged. 3. TONEPULSESWITCHisintheright position. 4 LINE CORD is plugged in the jack. Range of phone limited, check the following: I. ANTENNA on BASE UNIT is raised or re positioned. 2. BASE UNIT is centrally located in your residence. 3. BASE UNIT is not located near appliances.
[— CC REQUIREMENTS : EQUIPMENT NOTES This equipment is registered with the Federal Communications Commission and is in compliance with Part 68 of the FCC Rules and Regulations. On the bottom of this equipment is a label indicating among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. Upon request, you must provide this information to your telephone company.
LIMITED WARRANTY STATEMENT Statement of limited warranty: TT Systems LLC warrants that for a period of one year from the date of purchase that this product |) is free from defects in materials and workmanship and 2) conforms to its specifications. If this product does not function as warranted during the warranty period, TT Systems LLC, at its option, will either replace this product with cre that is functionally equivalent or will refund your purchase price.