User's Manual

ON/off button
ON/OFF button
Microphone
Sensitivity
Power On/OFF
Battery
compartment
Battery Installation
+
+
Insert 2 AAA battery compartment
Turn ON and turn OFF
This device has two ways to turn power on and off.
Hardware ON/OFF Slide the switch to ON or OFF
position.
If the slide switch is OFF, you cannot use the
software switch to turn on the power. If the unit is
not in use for a long period, use the hardware
switch to turn off the unit
Software ON/OFF This allows the transmitter to
be controlled externally.
Off: If the sensor is ON, press and hold the
software ON/OFF switch 5 seconds, the LED will
flash.
ON: If the sensor is OFF, press and hold the
software ON/OFF switch 5 seconds, the LED will
flash.
The sound sensor defaults to "ON" when the
hardware switch is moved from OFF to ON.
Hardware switch
Software switch
Code Matching & Melody Selection
The sound sensor works with the receiver (chime) and must be
paired prior to use.
Step 1: Insert batteries in the sensor to be used.
Step 2: Insert batteries in the receiver to be
used.
Step 3: Enter pairing mode for receiver
(chime unit). Press and hold the
learning button 3 seconds.
The LED #1 will flash.
Step 4: Press the button again to move to
the zone you want to pair with.
Press melody selector to scroll through
the melodies. Once you hear your
preferred melody, do not press again as
it is now selected.
There are 18 melodies & sound effects in
sequence.
Step 5: Switch on the sensor and speak into the microphone, the
red LED indicator will light. If successful, the receiver will
generate a short tone.
Press the button to exit pairing mode, the system is ready
to use
ID
Learning
button
Melody
selector
CHIM E
LIGHT
LIGHT & CHIME
Operation
1.Open the cover. 2. Slide the power to the ON position,
3.Select the desired sensitivity low, mid, or high, this sets the level
of sound required to trigger the transmitter.
4.Stick the microphone to the device you want to detect.
Open the cover
Slide the on/off switch
to OFF position
While pressing the test button
Slide the on/off switch to 'on'
position and hold the button 5
seconds. The LED will flash 5 times
when a new code is generated
Code Conflict
If the sound sensor coding and another transmitter is the same.
you must change the code of the sound sensor.
When you have changed the code of the sound sensor you will then
need to re- pair the sound sensor with the receiver.
FCC Statement:
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TY P E . D I SP O S E O F U S E D BAT TE R I E S AC CO R D I N G TO T H E
INSTRUCTIONS
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: Modifications to this product will void the user's authority to
operate this equipment.
USER MANUAL
SSX-201