User's Manual

ManualsBrandsVenture Global ManualsElectronicsDriveway Alert Sensor

Table Of Contents

USER MANUAL

Key Function On Receiver

Power

On/Off

DC jack

Volume

Indications on Receiver

* AC Power Operate: Light up blur LED while using

AC adaptor

* Back up Battery Operate: Light red LED while

operated by battery

* RX Battery Low: Flashs red LED with 0.3 sec. On /

5 sec. Off and sounds "beep" every half minute

* Remote Sensor Battery low: Flash red LED with 0.3

sec. On / 5 sec. Off and sound "beep"

AC Power on/

RX Batt. Low

#1 Zone/ Sensor

#2 Zone/ Sensor

#3 Zone/ Sensor

Remote sensor

battery low

#4 Zone/

Learn/Next

Melody/Batt.Chk

Pause/Reset

Cable come out

from Relay

Battery Cover

Power on/off : To switch on or switch off the receiver using this switch.

Volume: To adjust the volume level by rotating volume

DC jack: The AC/DC adaptor plug to this jack

Pause/Reset: Pause - Temporarily stop the receiver bypress and hold this button 3 sec.

Reset - Clear the sound and light on the receiver by press this button once

Melody / Batt. chk: See the chapter of learn and Check which sensor in battery low

Learn/Next: See the chapter of learn and Check which sensor in battery low

Bottom on Receiver

Remove the battery cover for setting the connection / time delay.

12V out

COM

+ -

Pause Time Setting

Pause mode

12V output control

1 S 5 S 10 S 60 S

Delay time setting

NO/NC control

30 min

60 min

Off On

A Output terminal: Connect to the device that you wanted control, such as Gate opener, Door

release or external alarm speaker .....

--- : this terminal output 12v 300mA when the select zone has been 12V out

trigger. (This terminal can not output 12V when using the backup battery.)

This output cooperate with "E". you can select which zone relayed to this

output by slide the DIP witch 1,2,3,4 on or off.

--- NO (Normal Open): this terminal output short circuit when the select zone

has been trigger.

--- NC (Normal Close): this terminal output open circuit when the select zone

has been trigger.

The NO and NS outputs cooperate with "F". you can select which zone

relayed to these output by slide the DIP witch 1,2,3,4 on or off.

B. Pause timer setting: Select the pause time 30 min or 60 min

C. Pause mode: EU mode: auto turn on when the pause time is over.

US mode: the receiver generat a beep tone when the pause time is over.

D. Delay time setting: These switch adjust the output time of the output terminal.

E. 12V output control: To choose which zone connect to the 12V output.

F. NC/NO output control: To choose which zone connect to NO/NC output.

Power & Setting

Install the 4 AAA batteries

into the battery compartment

as the indication on the

compartment

Although this receiver operate with AC/DC adaptor, we still need to install battery for backup.

Slide to open the battery cover

Replace the battery cover

Adjust the dip switch as you need and

Connect the wire to the device that you

want to control

The main power of this unit is 12V/500mA AC/DC adaptor

FCC Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Note: Modiﬁcations to this product will void the user's authority to operate this equipment.

Sensor

Summary of content (3 pages)

PAGE 1
USER MANUAL Key Function On Receiver Power On/Off Volume Pause/Reset Melody/Batt.Chk DC jack Learn/Next Battery Cover Cable come out from Relay Power on/off : To switch on or switch off the receiver using this switch. Volume: To adjust the volume level by rotating volume DC jack: The AC/DC adaptor plug to this jack Pause/Reset: Pause - Temporarily stop the receiver bypress and hold this button 3 sec. Reset - Clear the sound and light on the receiver by press this button once Melody / Batt.
PAGE 2
Installation Switch inside the transmitter Mount the transmitter on the wall 1.5m from the ground and slightly toward the ground and point to the target sensing area. Remove the screw from the top cabinet. Battery compartment Interval Timer 30 sec 7 sec After detect an intrude the sensor will sleep 7 seconds or 30 seconds. Test Button Sensitivity Photo sensor On/Off Off 12m 8m Filter 1-2m/sec Mark the 4 hole on the wall using a pencil. 7m On 4m 0.
PAGE 3
Learn (Pairing with remote sensor) 1. Press "learn" button and hold 3 second to entering to "learn mode" Battery low Receiver The "RX Batt. Low" LED (Red) will blink every 5 second and beep every 15 minute to indicate the backup batter low or no battery installed AC Power on (Blue)/ RX Batt. Low (Red) Battery Low Indication Power AC Power Battery Normal Indication Battery Low Beep sound every LED Indication 30 minutes Blue No Battery installed 2.