Submittal Coversheet Project Name DPS Project Number DPS Moore k-8 General Renovation PP2218 Date 6/17/2014 Architect Short Elliot Hendrickson 2000 South Colorado Blvd Tower One Suite 6000 Denver, CO 80222 GH Phipps 5995 Greenwood Plaza Blvd. Suite 100 Greenwood Village, CO 80111 Walrath 7935 West 14th Ave Lakewood, CO 80215 Contractor Subcontractor/Prepared by. Supplier Manufacturer Carrier Submittal Number 235400.
SUBMITTAL COVER SHEET JOB: DPS – Dora Moore LOCATION: Denver, CO CONTRACTOR: Walrath ENGINEER: The CE Group EQUIPMENT TAG QTY MODEL NUMBER DESCRIPTION AHU-1 1 FBRCNF030000 CU-1 1 38HDR024---3 AHU-1 1 KFADK0201DSC FB4C Base Series Fan Coil with Puron, 30,000 BTU Cooling, 208/230-1-60 Performance 13 Series Air Conditioner with Puron, 2 Tons Cooling, 208/230-1-60 Electrical Disconnect Kit “ 1 VCMA15ULS Little Giant Condensate Pump “ 1 T2900 Venstar Programmable Thermostat “ 1 ACC0400 O
Fan Coil and Air Conditioner SUBMITTAL Tag: AHU-1, CU-1 Model #: FB4CNF/38HDR Electrical: 208/230 Volt - 1 Phase – 60 Hertz Qty: 1 ea. Revision Date: 06/16/14 4800 OSAGE STREET DENVER, COLORADO 80221 PHONE: (303) 825-4328 WWW.LOHMILLER.
Project: DPS - Dora Moore K-8 Prepared By: Robert Bernal Unit Report Performance Summary Acoustic Summary Certified Drawing Table Of Contents AHU-1 CU-1 06/16/2014 2 3 4 5 Page 1 of 7
Unit Report For AHU-1 CU-1 Project: DPS - Dora Moore K-8 Prepared By: Robert Bernal 06/16/2014 Unit Report Outdoor Unit Parameters Unit Model: Unit Size: Voltage: 38HDR 2 Tons 208/230-1-60 V-Ph-Hz Outdoor Unit Dimensions and Weight Unit Length: Unit Width: Unit Height: Unit Shipping Weight: 0 0 0 198 in in in lb Indoor Unit Parameters FB4C Unit Model: 30,000 Btuh Unit Size: Cabinet Insulation:Single-piece cabinet with 1-in.
Performance Summary For AHU-1 CU-1 Project: DPS - Dora Moore K-8 Prepared By: Robert Bernal 06/16/2014 Performance Summary System Performance System: System Quantity: Altitude: Linear Pipe Length: SEER @ ARI Conditions: EER @ ARI Conditions: 38HDR/FB4C 1 5200.0 ft 0.0 ft 14.5 12.0 Actual Airflow: Standard Airflow: Total Net Clg Capacity: Net Sensible Clg Capacity: Total System Power: 968.7 800.0 20.89 20.89 2.
Acoustic Summary For AHU-1 CU-1 Project: DPS - Dora Moore K-8 Prepared By: Robert Bernal 06/16/2014 Acoustic Summary Outdoor Unit Parameters: Unit Model: Unit Size: Variations: Octave Band Center Frequency, Hz Sound Power,dB A-Weighted Sound Power, dBA Indoor Unit Parameters: Unit Model: Unit Size: Cabinet Insulation: Octave Band Center Frequency, Hz Sound Power,dB A-Weighted Sound Power, dBA 38HDR 2 Tons Standard 63 0.0 125 57.5 250 61.5 500 63.0 1k 61.0 2k 60.0 4k 56.0 8k 45.0 dBA 69.
X X X X X X O O O O O O 230-1-60 208-230-1-60 O O O X X X O O O X X X 18,24 30,36,48,60 23" X 42" 24" X 50" B B X = YES O = NO 25 1/8" 36 15/16" 31 1/8" 36 15/16" 37 3/16" 44 9/16" 37 3/16" 44 9/16" 43 3/16" 44 9/16" 43 3/16" 44 9/16" MINIMUM UNIT SIZE MOUNTINGPAD DIMENSIONS A 38HDR018 1 38HDR024 1,2 38HDR030 1 38HDR036 1 38HDR048 1,2 38HDR060 1,2 208/230-3-60 ELECTRICAL A UNITSERIES CHARACTERISTICS DIM ENSI ONS -- ENGLI SH 460-3-60 C F D E F E G AIR H 22" 28" 34 1/16" 34 1/16" 40
Certified Drawing for AHU-1 CU-1 Project: DPS - Dora Moore K-8 Prepared By: Robert Bernal 06/16/2014 DIMENSIONS A12512 Fig.
Certified Drawing for AHU-1 CU-1 Project: DPS - Dora Moore K-8 Prepared By: Robert Bernal 06/16/2014 (cont.) DIMENSIONS A12508 Fig.
Electrical Disconnect SUBMITTAL Tag: AHU-1 Model #: DFADK0201DSC Qty: 1 Revision Date: 06/16/14 4800 OSAGE STREET DENVER, COLORADO 80221 PHONE: (303) 825-4328 WWW.LOHMILLER.
Installation Instructions Electrical Disconnect Kit KFADK0201DSC NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. SAFETY CONSIDERATIONS Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may cause personal injury or property damage.
CASING UNIT GROUND FAN COIL BLOWER SHELF MOUNTING BRACKET COVER PLATE A90084 Fig. 1—Installation of Disconnect Kit 9. Cut insulation away from rectangular access hole in blower access panel. → 10. Remove adhesive backing from window bezel. From the outside of the door, insert the window through the rectangular hole in the door. Press the frame firmly on the door surface to seat the adhesive. (See fig.3) 11. Replace blower access panel. 12.
ADHESIVE LINE WINDOW BEZEL PULL TO DISCONNECT LOAD GROUND PRIOR TO ADHERING WINDOW SEAL TO DOOR PANEL, MAKE CERTAIN THAT THE RECTANGULAR CUTOUT IS DOWN. NOTE: Route wires as shown A00001 A03064 Fig. 2—Wiring Connections Fig.
Condensate Pump SUBMITTAL Tag: AHU-1 Model #: VCMA15ULS Electrical: 115 Volt - 60 Hertz Qty: 1 Revision Date: 06/16/14 4800 OSAGE STREET DENVER, COLORADO 80221 PHONE: (303) 825-4328 WWW.LOHMILLER.
HVAC VCMA-15 Series Applications •• Designed for automatic collection and removal of condensate from air conditioning, refrigeration and dehumidification equipment when gravity drainage is not possible or practical. Also suitable for high efficiency oil and gas-fired condensing furnace and condensing boiler equipment.
Engineering Data " " " " " " " " " " " " " Specifications Item No. Model No. Discharge Size Performance (GPH@Head) HP Volts Hertz Amps Watts 1' 5' 10' Shutoff 20' Ft PSI Cord Length (ft) Weight (lbs) 554401 VCMA-15UL 3/8" OD Barbed 1/50 115 60 1 60 65 50 25 0 15 6.5 6 4.40 554411 VCMA-15ULT 3/8" OD Barbed 1/50 115 60 1 60 65 50 25 0 15 6.5 6 5.80 554405 VCMA-15ULS 3/8" OD Barbed 1/50 115 60 1 60 65 50 25 0 15 6.5 6 4.
Thermostat and Sensor SUBMITTAL Tag: AHU-1 Model #: T2900/ACC0400 Qty: 1 ea. Revision Date: 06/16/14 4800 OSAGE STREET DENVER, COLORADO 80221 PHONE: (303) 825-4328 WWW.LOHMILLER.
Venstar Programmable Thermostat T2900 STANDARD FEATURES: • Up to 3-Occupied, 1-Unoccupied periods per day, with copy command for easy programming • Light Activated occupied period (defeatable) • Accepts humidification/dehumidification control module (Venstar part number ACC0430) • Auto changeover, 3-stage heat, 2-stage cool for use with gas/electric, heat pump, electric & hydronic heat • Configurable for manual changeover, also configurable programmable or non-programmable • Adjustable deadbands and timers
wired sensors accessories Model ACC0401 The remote indoor temperature sensor with override button offers the user the ability to change commercial thermostats to Occupied mode for after-hours heating or cooling. It will measure indoor-air temperature at a remote location from the thermostat. It is a digital sensor designed for use with Venstar thermostats. It can be used with the Venstar T1800, T1900, T2700, T2900, T2900SCH and T2300FS thermostats.
Low Ambient, Evap Freeze T-stat, TimeDelay Relay, Winter Start Control, Wind Baffle, Crankcase Heater SUBMITTAL Tag: CU-1 Model #: 53DS-900---086, KAAFT0102AA, KAATD0101TDR, KAAWS0101AAA, 53DS-900---087, KAACH1401AAA Qty: 1 ea. Revision Date: 06/16/14 4800 OSAGE STREET DENVER, COLORADO 80221 PHONE: (303) 825-4328 WWW.LOHMILLER.
53DS---900--- --- ---086 53DS---900--- --- ---095 Duct---Free Systems Cooling Only and Heat Pump Units Low Ambient Temperature Control Accessory Installation Instructions NOTE: Read and become familiar with these instructions before beginning installation. SAFETY CONSIDERATIONS Installing and servicing air--conditioning equipment can be hazardous due to system pressures and electrical components. Only trained and qualified personnel should install or service air--conditioning equipment.
Winter Start Control (part number KAAWS0101AAA) is required when low ambient operation (cooling below 55_F/13_C) is required for cooling and heat pump models (018--060) that have a low pressure switch. INSTALLATION For 38HDR/QRR Models 1. Remove access panels and locate pressure tap on liquid header. 2. Place three drops of compressor oil in the pressure switch for lubrication. 3. Mount switch as shown in Fig. 1. 4. For heat pump units only, mount isolation relay in control box. 5.
COOLING ONLY MODELS Wire Color Black = 009 & 012 Red = 018 & 024 Black Black Black Black 38MVC009--- 024 38HDF018--- 036 38HDR018--- 060 538A Series 538E Series LAC SEE CHART FOR COLOR BLU TO TERMINAL CONNECTION MAIN POWER BLU FAN MOTOR LEGEND LAC = Low Ambient Control A08047 Fig. 3 -- Low Ambient Temperature Control Wiring -- Cooling Only Models HEAT PUMP MODELS (Reversing Valve Energized in Cooling) Model No.
CHECK OPERATION 53DS-- 900-- -- -- 086, 095 Before starting the system to check operation of low ambient temperature control, ensure that the power wiring and location of control assembly are correct. To check operation of low ambient temperature control: 1. Turn power on to system. 2. Set thermostat below room temperature. 3. Ensure that there is the standard 3--minute time delay for the microprocessor controlled high wall fan coil systems. 4.
Installation Instructions Evaporator Freeze Thermostat KAAFT0101AAA NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. INTRODUCTION This instruction covers the installation of evaporator freeze thermostat Part No. KAAFT0101AAA on split-system air conditioners and heat pumps. The device is designed to shutdown the outdoor section in the event of indoor coil freeze up, preventing damage to the compressor.
3⁄16-IN. HOLES TO CONTROL WIRING A97510 → Fig. 1—Mounting Thermostat on Coil Casing 6. Mount electrical box to plenum or casing using 2 No. 10-24 X 1/2-in. sheet metal screws. (See Fig. 1.) 7. Mount evaporator freeze thermostat to side of electrical box using 2 No. 8-32 X 1/2-in. sheet metal screws. 8. Route wires for bulb through knockout hole in electrical box, and connect to evaporator freeze thermostat. 9.
TIME--DELAY RELAY KIT KAATD0101TDR Installation Instructions NOTE: Read the entire instruction before beginning the installation. INTRODUCTION The Time--Delay Relay permits the indoor fan to briefly continue to operate and provide additional cooling after the compressor cycles off. SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment can be hazardous due to system pressure and electrical components. Only trained personnel should install or service air conditioning equipment.
FAN-COIL OR FURNACE LOW-VOLTAGE TERMINAL BOARD R G Y W C FIELD CONNECTIONS BRN RED ORN BLK KAATD 1/ 8 IN. DIA FAN TIME- (2) SCREW DELAY HOLES FROM G ON THERMOSTAT 2 15/16″ 1 15/16″ Fig. 1 -- Typical Time--Delay Relay Wiring Connection Copyright 2006 CAC / BDP S 7310 W. Morris St. S Indianapolis, IN 46231 Printed in U.S.A. Edition Date: 05/06 Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
KAAWS0101AAA Winter Start Control Installation Instruction NOTE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment can be hazardous due to system pressures and electrical components. Only trained personnel should install or service air conditioning equipment. Untrained personnel can perform basic maintenance functions such as cleaning coils, or cleaning and replacing filters.
LPS Run Wire Blue Tap Wire Wire Contact Base Blue Tap Wire Wire Stop Yellow w/ Red Plastic Flange A07934 A07944 Fig. 1 -- Installation 24 VAC 24 VAC (Y) T3 LPS (C) C T1 LPS = Low Pressure Switch C = Contactor Coil T1 = 24 VAC Input T2 = Switch Override T3 = 24 VAC Com TDR = Time Delay Relay Circuit Board T2 A07933 Fig.
53DS---900--- --- ---070 53DS---900--- --- ---071 53DS---900--- --- ---087 53DS---900--- --- ---088 Duct---Free Systems Cooling Only and Heat Pump Units (Size 018---060) Accessory Wind Baffle Kit Installation Instructions 2 To 5 Nominal Tons NOTE: Read and become familiar with these instructions before beginning installation. SAFETY CONSIDERATIONS Installing and servicing air--conditioning equipment can be hazardous due to system pressures and electrical components.
Table 1—Kit Contents and Usage Wind Baffle Kit Part No.
KAACH1201 KAACH1301 KAACH1401 KAACH1501 KAACH1601 KAACH1701 KAACH1801 KAACH1901 KAACH2001 KAACH2101 KAACH2201 KAACH2301 KAACH2401 Crankcase Heater Kit Installation Instructions NOTE: Read the entire instruction manual before starting the installation. Use only the kit components described in this installation procedure. SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment can be hazardous due to system pressures and electrical components.
CRANKCASE HEATER 2” (50.8 mm) HEATER FASTENING CLIP COMPRESSOR POWER LEADS A90297 Fig. 1 -- Crankcase Heater Installation CRANKCASE HTR BLK BLK 11 TEMP SWITCH CRANKCASE HTR BLK BLK BLK 11 21 BLK 21 A06075 A97586 Fig. 2 -- Crankcase Heater Wiring (for kit numbers 1201, 1301, 1401, 1501, 1801, 1901, and 2001) Fig. 3 -- Crankcase Heater Wiring (for kit numbers 1601, 1701, and 2101) CONTROL BOARD CCH BLK CRANKCASE HTR BLK BLK 11 21 A11629 Fig.
A11630 Fig.
Edition Date: 09/12 Copyright 2012 CAC / BDP S 7310 W. Morris St. S Indianapolis, IN 46231 Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.