VMS-8 Subwoofer USER’S MANUAL Small, High-Performance Subwoofer
. www.velodyne.
Ta b l e o f C o n t e n t s Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Prepare for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Line-Level Connection - Option A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Congratulations! Congratulations on your purchase of a Velodyne VMS subwoofer system. This system represents the state-of-the-art in home audio reproduction and will provide you with years of listening pleasure when properly cared for. Read and follow this instruction manual to insure safe and proper system connection and operation. Caution! Please observe the following instructions to insure safe and proper system operation.
P r e p a r e f o r I n s ta l l a t i o n Your new Velodyne subwoofer provides for a number of installation options. Read all the installation information below in order to determine which installation option is best for your system. Remember to perform all installation procedures with system power turned off to prevent possible damage. Placement The first step in installing your new VMS is to determine where it will be placed in the room.
I n s ta l l a t i o n Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when connecting your subwoofer to a pre-amp, signal processor, line-level crossover or receiver with pre-amp level outputs. The SPEAKER LEVEL jacks connect directly to the speaker outputs of any amplifier, integrated amplifier or receiver. Your amplifier section will notice no additional loading effects when you use these inputs due to their very high impedance.
Crossover Switch - INTERNAL X-OVER/SUBWOOFER DIRECT This switch allows the internal crossover circuitry to be removed from the signal path. This is required in certain installations which route the signal through external processors with a crossover circuit of their own, such as the new digital units. Simply move the switch to SUBWOOFER DIRECT to disengage the built-in crossover.
Figure 1. Installation Using LFE Line-Level Inputs Note: If not using an external crossover, you should use the built-in crossover for optimal performance. When using a single channel input (such as a surround sound processor’s subwoofer out or LFE), the auto on/off circuit sensitivity will be affected. When one input channel is used instead of two, the unit will see lower signal levels present at the inputs. This may cause the unit to turn off when listening at low volume levels.
Line-Level Connection - Option B Figure 2 shows connection from a pre-amplifier’s main outputs to the left and right inputs of your Velodyne subwoofer. You will also need to connect a second pair of RCA cables from the outputs on the back of your subwoofer to the inputs on the back of your amplifier.
Speaker-Level Connections Figure 3 shows an easy way to connect your Velodyne subwoofer directly to your receiver or integrated amplifier, if it lacks line-level outputs. You may also connect your satellites directly to your receiver or amplifier along with the subwoofer. Your receiver or amplifier will not notice the additional load of the subwoofer due to the high input impedance. Figure 3.
Subwoofer Outputs The Velodyne subwoofer is designed to operate using the full range audio signal for input when using the built-in crossover. Many home theater processors/receivers (Dolby Digital®, DTS®, THX™) have a “subwoofer out” jack that is internally filtered and designed to be used with a powered subwoofer. In these installations, you may bypass the internal crossover in either the processor or the Velodyne subwoofer.
C a r e o f Yo u r S u b w o o f e r Your Velodyne subwoofer does not require any regular maintenance. Normal dusting or cleaning of the surface for appearance purposes is all that is required. We suggest you avoid any harsh detergents or chemicals when cleaning the cabinet. Abrasives, detergents, or cleaning solutions may damage the finish on the cabinet. We recommend using only a damp cloth to clean the cabinet. During normal conditions, your new subwoofer may be left on continuously without any problems.
Specifications . Specifications VMS-8 Woofer 8” forward firing (6.5” piston diameter) Amplifier (Class D) 2000 watts Dynamic 1000 watts RMS Power High Pass Crossover 80 Hz (6 dB/octave) Low Pass Crossover 40 Hz-120 Hz 12 dB octave initial, 48 dB octave ultimate Frequency Response 26-120 Hz (+/-3 dB) Harmonic Distortion <5% (typical) Magnet Structure 204 oz. (12.7 lbs) Voice Coil 2.
Velodyne Products 115 - 120V DD ® Series DD-10 DD-12 DD-15 DD-18 Digital Drive 1812 Signature Edition DEQ-R Series DEQ-8R DEQ-10R DEQ-12R DEQ-15R DLS™-R Series DLS -3500R DLS -3750R DLS -4000R DLS -5000R Impact Series Impact - Mini Impact -10 Impact -12 MicroVee™ Optimum Series Optimum-8 Optimum-10 Optimum-12 SMS™-1 SubContractor™ Series SC-1250 SC-10 SC-12 SC-15 SC-IW SC-IF/IC SC-600 Amp SC-600 IW SC-600 IF/IC VDR Series VDR-10 VDR-12 220 - 240V DD ® Series DD-10 DD-12 DD-15 DD-18 Digital Drive 1812 Sig
FOR YOUR RECORDS. . . Date Purchased_________________________________________________________________ Dealer_________________________________________________________________________ Serial #________________________________________________________________________ *NOTE: Please complete and return your warranty card within ten (10) days or Register. . . ON LINE . . . It’s faster . . . and easier www.velodyne.com LIMITED WARRANTY - U.S. AND CANADA ONLY VELODYNE ACOUSTICS, Inc.
Velodyne Acoustics, Inc. 345 Digital Drive Morgan Hill, CA 95037 408.465.2800 voice 408.779.9227 fax 408.779.9208 service fax www.velodyne.com Service E-mail: service@velodyne.com Product E-mail: help@velodyne.com Technical E-mail: techhelp@velodyne.com . 63-VMS Rev A MAY09 www.velodyne.