Velodyne DLS-3500R™ DLS-3750R™ DLS-4000R™ and DLS-5000R™ Userls Manual DSP-Controlled Home Theater Subwoofer
A_I IA Caution To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. The lighting flash with arrowhead symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
I Congratulations! Congratulations on your purchase of a Velodyne Distortion Limiting System™ Remote (DLS-R) subwoofer. This system represents the state-of-the-art in low frequency reproduction. Read and follow the instructions below to insure safe and proper system operation. Warning! To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open speaker enclosure or amp chassis cover. Please observe all warnings on the equipment itself.
• • • Anti-clipping circuit Over excursion protection Slot loaded design Installation Your new subwoofer system provides for a number of installation options. Read all the installation information below in order to determine which installation option is best for your system. Remember to perform all installation procedures with system power turned off. LOW-PASS CROSSOVER • up©) DOWN©) Velodyne DLS-R Series AUTO ONIOFF ......- -.......
RearPanelConnecuons Figure 1 shows the connections on the rear panel of the DLS-R. Following are brief descriptions of the connections described in Figure 1. More detail on these connections can be found on the next page. (1) LOW..PASS CROSSOVER Use this knob to select the high-frequency range at which you wish to cut off the signal to the subwoofer. When the knob is turned all the way to the left, the Subwoofer Direct feature is invoked and the subwoofer plays all frequencies up to 200 Hz.
(6) HIGH PASS CROSSOVER Switch This switch selects the frequency for the high pass crossover. This crossover is functional on both line and speaker-level outputs. Smallerspeakerswith limited lowfrequencyoutput may perform better using the higher 100 Hz setting that will reduce the low frequencies sent to them. Larger speakers with greater low frequency output may be able to handle the 80 Hz setting without strain.
You should set the crossover frequency to obtain a smooth and seamless transition from the subwooferto the main speakers in your system. If your main speakers are smaller units with limited low frequency output, you may wish to choose a higher frequency (such as 100-120 Hz) than you would with larger speakers which have greater low frequency output. With larger speakers, you might start with this control set lower, such as 80 Hz.
out" jack that performs this same function and are designed to be used with a powered subwoofer. In these installations, you may want to bypass the crossover in either the processor or the Velodyne subwoofer. In some cases, you may want to use BOTH crossovers. To do this, you can use both your processor's crossover and the one internal to the Velodyne sub. You should stagger the frequencies (i.e., 120 Hz subwoofer, 80 Hz processor) for best results.
room and system conditions often dictate otherwise. Keep in mind that frequency response and output level can be drastically influenced by placement, depending on the acoustic properties of your listening room. Typically, the optimum location for a subwoofer is in a front corner of your listening room. This location will usually offer the greatest output levels and optimum low frequency extension.
Usage This section addresses day-to-day usage of your DLS-R subwoofer. Remote Control Figure 2 shows the remote control, enabling you to easily choose whatever listening mode you desire. Figure 2. Remote Display POWER - This button forces your DLS-R unit into standby mode. The woofer will not play and the LED will turn off. The unit will remain in this mode until the POWER button is pressed again. To fully deactivate (i.e. power down) the unit, turn off the power switch on the back panel.
PHASE - These buttons allow you to optimize the subwoofer performance for the location and your listening position. Select the switch position at which you hear the most bass. The light will blink according to the following schedule: odegrees 90 degrees 1 blink 2 blinks 180 degrees 270 degrees 4 blinks 3 blinks LIGHT -If you wish, you can deactivate the blue front pane/lights on your DLS-R unit. To do this, press the LIGHT button on your remote. The light will turn off.
Jazz - Classical: Games: The tightest, cleanest, lowest distortion bass. Maximum loudness available for the impact of video games. The following table indicates musical style and which preset is recommended for it.
Each preset has its own characteristics with respect to subsonic filter, volume differential, and a single equalizer (EQ) in order to optimize the listening mode for the preset.
During normal conditions, the subwoofer may be left on continuously without any problems. If you plan to leave the unit unused for an extended period of time, we recommend that you turn off the unit by the master power switch on the rear panel. Troubleshooting and Service Before seeking service for your subwoofer, please re-check all systems. Following is a simple troubleshooting guide to assist you. 1. Verify that the unit is plugged in and power outlet used is active. 2. Is the power switch on? 3.
SPECIFICATIONS DLS\35OOR DlS3750R DLS4000R Cabinet (H,V'J,O) (cm) 16" x 15" x 17.75" 40 x37.5x 44 18" x 15 x 19 45 x 37.5 x 47.5 15" x 12" x 15.75" 37.5x30x39 FnequencyResponse 35Hz-140 Hz (+/-3 dB) 28Hz~120 11 Ol£5(XX)R 11 Hz (+/-3 dB) 25Hz-120 Hz (+/- 3dB) High Pass Crossover 80 Hz or 100Hz (6 dB/octave slope) Low Pass Crossover 40 Hz -120 Hz (12 dB/octave, 24 dB ultimate) 21" x 18.4~' x20.75" 52.
FOR YOUR RECORDS. .. Date Puchased _ Dealer Serial # _ _ *NOTE: Please complete and return your warranty card within ten (10) days or Register. .. ON LINE . .. It's faster . .. and easier www.velodyne.com LIMITED WARRANTY VELODYNE ACOUSTICS, Inc. ("VELODYNE") warrants all powered subwoofers for a period of two years, and full range speakers for a period of five years.
Notes 16
"Not only was the little Velodyne the best small sub I've ever used, it was one of the very best subs I've used.
return address place stamp here Velodyne Acoustics, Inc.
Velodyne OWNERS REGISTRATION 1. Name _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _~Street _ City _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ State _ _ Zip _ Phone _ _ _ _ _ _ _ _ _ _ _ _ _ _ Alternate Phone _ E-mail 2. Product Model, S/N _ Date Purchased _ _ _ _ _ _ _ _ _ _ Purchase Price ~ 3. Dealer Name _ _ _ _ _ _ _ _ _ _ _ _ _ Address _ City _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _~State _ _ Zip _ 4. Comments: 5. Would you like to be notified of new Velodyne products or special promotions via email? 6.
Ve-Iodyne Velodyne Distortion Limiting System™ R (DLS-R) Series Subwoofers Additional Information This sheet provides additional information on the DLS-3500R, DLS-3750R, DLS-4000R and DLS-5000R subwoofers. Restore Defaults. There is a feature not documented in the user's manual that allows you to restore default settings for your DLS-R Subwoofer. By pressing Presets in EXACTLY the following order on the remote, the unit's power light will blink three times indicating that you have restored defaults. 1.