VEC120S CANDLE POWER 3,000,000 SPOTLIGHT CORDED•CORDLESS•RECHARGEABLE WITH BUILT-IN CCFL AREA LIGHT OWNER’S MANUAL & WARRANTY INFORMATION IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS PRODUCT. PLEASE READ CAREFULLY BEFORE USE AND RETAIN FOR FUTURE REFERENCE. 4140 S.W. 28th WAY, FT. LAUDERDALE, FL 33312 Tel: (954) 584-4446 Fax: (954) 584-5556 Toll Free: (866) 584-5504 www.vectormfg.
IMPORTANT SAFETY INSTRUCTIONS WARNINGS: Contains non-spillable sealed lead acid batteries. They must be recycled or disposed of properly. DO NOT dispose of batteries in fire, as this may result in an explosion. DO NOT open battery or short circuit, as this may cause the battery to leak or get hot causing personal injury. Any disposal questions call toll-free (887) 288-7722. Please read Instruction Manual completely for all safety and warning instructions.
TWO YEAR LIMITED WARRANTY REGISTRATION FORM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty, other than those described herein. This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of defects in materials and workmanship for two years from the date of purchase without additional charge.
6
1. INTRODUCTION Congratulations on purchasing VectorLite TM Model VEC120, an advanced design dual- bulb 3.000,000 candlepower spotlight and long lasting, soft Cold Cathode Fluorescent Lamp (CCFL) area/bug light. It uses two powerful proven-technology rechargeable, non-spillable sealed lead acid batteries that allow for years of dependable use, recharge after recharge.
2. ADDITIONAL FEATURES • Two powerful, prefocused, replaceable quartz halogen bulbs in spotlight. • CCFL Area/Bug Light provides up to 48 hours of continuous operation. • CCFL Area/Bug light flips up for good area light distribution; down for bug light use. • Three-position slide switch selects single or dual spotlight, or CCFL operation. • Trigger Switch operates spotlight. • Rubber safety guard (bezel) around lens protects spotlight.
WARNINGS: DO NOT ALLOW BARE WIRES OR CONNECTORS TO CONTACT EACH OTHER DANGEROUS SPARKING CAN OCCUR - NOTE WHICH WIRES ARE ON THE BATTERY TERMINALS 6. Note polarity of battery. Note which wire is on which terminal. 7. Disconnect the wires from the battery and set the battery aside. 8. Connect the replacement battery, making sure the correct wires are on the new battery terminals. Make sure POS (+) is red and NEG (-) is black.
14. Place the reflector in position in the body of the spotlight. 15. Replace the rubber ring in the groove around the perimeter of the reflector. 16. Replace glass and Retainer so that the screw holes are aligned. 17. Secure Retainer with two Phillips screws. 18. Replace Rubber Bezel by sliding forward to the front of the spotlight. 19. Operate switchs to ensure proper operation of spotlight.
4. CHARGING THE VECTORLITE USING THE AC RECHARGE ADAPTER NOTE: This unit is shipped in a partially charged state. Initially charge unit using the AC charger. To check the battery level, press the Battery Status Pushbutton (Figure 2). Charge until Battery Status Displays green LED lights when the Battery Status Display Pushbutton is pressed. Charge after each use. See Figure3A AC/DC Recharge Adapter.
5. CHARGING AND POWERING THE VECTORLITE USING THE DC RECHARGE ADAPTER The VEC120 can be simultaneously charged and operated from a12 volt DC source. Make sure the 12 volt source can supply at ;least 15 amperes of current if the spotlight is to be operated while the batteries are being charged. To check the battery level, press the Battery Status Pushbutton (Figure 2). Charge until Battery Status Display?s green LED lights when the Battery Status Display Pushbutton is pressed. Charge after each use.
Rubber Bezel Reflector Assembly Retainer Reflector Phillips Screws Lens (Glass) Rubber Ring Hairpin Retainer Wires To replace either or both H3 type 12 volt bulbs, you will need a small Phillips type screwdriver and a replacement bulb (or bulbs) Vector Part VEC190. Bulb life can be shortened by installing a bulb with dirt or fingerprints on it. The bulb can be wiped clean with cloth moistened with alcohol. During bulb installation, avoid touching the glass part of the bulb.