Welcome Thanks for your purchase! This 77 AHD wireless backup camera Is major designed to make it easier and safer to get in and out of the parking space. Please read this manual carefully before installing and using. If you encounter any problems during installation or use, please contact customer service: service@veclesusclub. m. We reserve the rights to modify printing errors or update specifications without a prior notice. We hope can get your understanding.
1. Components... LIVY. 12VMW7-2€. 1IVMWT-4C. 2. Safety Information: 3. Getting Started. 3.1 Test the system. 3.2 Before Beginning Installation. Installation Good subsystem Connection Diagram. 4.2 Recommended Installation Location... 4.3 Powered The Monitor By Cultural Fuse.. 4.4 Camera Installation... 4.5 Mount the Monitor . 5. Operation. perpetrate the Monitor. 5.2 Activate the Camera. 5.3 Camera Paladin, 6. Specifications... 7. Care and Maintenance... 8. Troubleshooting... 9. Warranty... 1.
VMW7-2C 7 Inch Wireless Monitor =m —rrm arm Antenna* Installation Accessories.
2, Safety In formations Usage + This wireless backup camera systematize/ VMW7-2C/ designed to help the driver safely detect people and/or objects helping to avoid damage ar Injury. However, you the driver, must use it properly. Use of this system is not a substitute for safe, proper or legal driving. + Never back up/driving while looking at the monitor alone.
3.2 Before Beginning Installation As the cameras) needs ta be fixed on the vehicle, it may need ta drill a hole on your car, before drilling please measure the size of boreholes and check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle s In use. Keep all cables away from hot or moving parts and electrical noisy components.
VMW7-4C 10 4.3 Powered The Monitor By Cultural Fuse If you don't want to use car cigarette lighter to power the monitor, you can those to a direct connection to the power supply by the power cord, follow these steps: 1. Find the car circuit fuse box{according your car user manual] under your car cab. 2. Then according to the labels on the fuse hardware kit, and put the corresponding power fuse connect to the corresponding trigger line{voltage must between 12-24V).
4.4 Camera Installation 1. Find the best installation position to install backup cameras) on your vehicle. 2. Remove the camera(s) U-shaped bracket, mark the hole position with a marker pen, then drilling, after the hale Is finished, route the terminal wire of the camera through It and Install the screw of the backup camera. 3. Be sure to use the vibration gasket when installing the camera. it Is package with the camera hex wrench. 12 4.5 Mount the Monitor 1.
4. Move the bracket to the proper location. 5. Fix the big screws of the bracket and keep the monitor tight. 6. If you want to change the direction or angle of the monitor, firstly to loosen the screws on the bottom of the bracket. Then move the monitor to the desired location then fix the screws on the bottom of the bracket again. 14 5. Operation 5.
Buttons from Left to Right Decrease Menu control button Increase Rawer off/on button. Red back light: system standby, Blue back light: system has been powered Flip set: Turn Up, Down, Left and Right Ele Parking guide line: ON/OFF. (HGT: The multi-camera system needs to adjust the split-screen to a single screen to set the parking guide line On/Off) Pairing button (VMW?7: Long press this button to pairing the camera.
6. Specifications Camera 3.41In System SCENT 7.09in Operational Current 300m 3.03In d {when transmitting) Pixels 1080P 1960*1080 Pixels Viewing Angle 140 Image Sensor CP7210CMOS Monitor LCD Di play Screen Size 7 Inch IPS Panel awe daemons Transmission distance 200M In open area Connector 2 Pin Mini BM connector 2.
7. Care and Maintenance Please do not use solvents or chemicals to clean or wipe the camera. If necessary, use a soft cloth dipped In neutral detergent to clean the dirt or stains. The system is designed to provide years of service and should be recycled or safety disposed of at local recycling center. Er 8. Troubleshooting Error/malfunction Possible Causes Solutions/repair The monitor does not display images The monitor is notion standby status Please make sure that the monitor Is powered.
Error/malfunction Possible Causes Solutions/repair The monitor dose not display Images Please check and make sure If the GND wire (black wire) is properly connected, please use a chassis ground post. The black underwired) is not connected properly The image shakes when the vehicle Is moving The red power wire Is not Please check and make sure If the hot wire connected properly {red power wire) is properly connected.