User Manual

ManualsBrandsVecima Networks ManualsElectronicsRadio Module

Table Of Contents

LMS3000 Technical

Note

Lawrence Gordon Page 1 of 8 Last saved on 27-Mar-06 5:45 PM

F:\Tech Notes\TN131C - 915A Radio Operational Requirements.doc

Number: TN131C

Title: 915A Radio Operational Requirements

Author: Lawrence Gordon

Reviewer:

Date: 27-Mar-06

Pages: 8

Abstract:

This document lists the requirements that must be met in order to use the WaveRider 915A

Radio in different packages and configurations.

Revision History:

Date Rev. Author Comments

24 Mar

‘06

A L.

Gordon

Initial Approval for AC to 4.2 VDC power supply; Indoor, and YAGI antennas

27 Mar

‘06

B L.

Gordon

Add FCC / IC Warnings, indicate that Radio Module can only to be installed by

WaveRider manufacturers

27 Mar.

‘06

C L.

Gordon

Correct Antenna gain

Summary of content (8 pages)

PAGE 1
LMS3000 Technical Note Number: TN131C Title: 915A Radio Operational Requirements Author: Lawrence Gordon Reviewer: Date: 27-Mar-06 Pages: 8 Abstract: This document lists the requirements that must be met in order to use the WaveRider 915A Radio in different packages and configurations. Revision History: Date Rev. Author Comments 24 Mar ‘06 A L. Gordon Initial Approval for AC to 4.2 VDC power supply; Indoor, and YAGI antennas 27 Mar ‘06 B L.
PAGE 2
TN131C 915A Radio Operational Requirements Table of Contents 1 Introduction........................................................................................................................ 3 1.1 References ................................................................................................................ 3 2 Requirements.................................................................................................................... 3 2.1 Regulatory Notices Requirements ............
PAGE 3
TN131C 915A Radio Operational Requirements Appendix A1 INTRODUCTION The WaveRider 915A Radio is certified by FCC and Industry Canada (IC) under a Limited Modular Approval (FCC ID: OOX-915A and IC ID: 3225B-915A). This means that the radio can be used in various packages and configurations provided the requirements below are met. These requirements apply to any WaveRider final product using the 915A radio.
PAGE 4
TN131C 915A Radio Operational Requirements All versions of this device have been tested using unshielded Ethernet CAT-5 cable. Notice to User Any changes or modifications to equipment that are not expressly approved by WaveRider may void the user’s authority to operate the equipment. 2.1.1 FCC The 915A radio has been designed and manufactured to comply with FCC Part 15 under FCC ID: OOX-915A.
PAGE 5
TN131C 915A Radio Operational Requirements 3. The operator of a spread spectrum system and the user of the radio device are each responsible for ensuring that the system is operated in the manner outlined in the section on Interference Environment above. The 915A radio with its certified antennas complies with these requirements when installed correctly as detailed in this manual. 2.1.2 Industry Canada The 915A radio has Industry Canada (IC) Certification Number 3225B-915A.
PAGE 6
TN131C 915A Radio Operational Requirements radio and any of its final products and should be included in any final product installation guide, edited as appropriate (e.g. use final product name rather than 915A Radio). The regulatory notices in sections 2.1.1, 2.1.2, and 2.1.3 must be included in the installation guide for the final product edited as appropriate (e.g. use final product name rather than 915A Radio).
PAGE 7
TN131C 915A Radio Operational Requirements If the 915A radio is powered by a supply other than the AC lines (e.g. vehicle power) then no testing is required. B.22.5 Antennas Only antennas that have been approved by FCC and IC shall be used with the 915A radio. This means that any antenna of the same family with a gain less than or equal to the approved antenna can be used. The list of approved antennas is given in Appendix A, which will be updated as new antennas are approved.
PAGE 8
TN131C 915A Radio Operational Requirements Appendix A3 APPROVED CONFIGURATIONS A.13.1 Approved Power Supplies Table 1 – Approved Power Supplies # Power Supply 1 Fairway WVG 10F-420A Voltage Comments AC to 4.2 VDC A.23.2 Approved Antennas Table 2 – Approved Antennas # Antenna Type Max. Gain Required Loss @ max. gain Separation Comments Distance 1 WaveRider Indoor Diversity 4.4 dBi 0 20 cm Approved for indoor use. 2 YAGI 13 dBi 4.