Reach TM USER GUIDE
Table of Contents What is included .................................................................................. Set up ...................................................................................................... Lock ......................................................................................................... Unlock ..................................................................................................... Adding new fingerprint .........................................
What is Included? 2X Keys 1X Holster Insert 1X Reach Unit 1X User guide 1X Allen wrench 1X Charging mount 1X Charging cable Reach 4X Screws
Set up - Biometric A Press the white button to start fingerprint registration process Note: If you already registered your master RFID, you must unlock Reach first with your tag and then press the white button within 5 seconds, to enter the master RFID registration process Unit turns on and the top lights all turn red B Place finger onto the fingerprint sensor One of the red lights will turn green Lift finger and repeat until all lights turn green (3 times in total) C You have now registered the “mas
Set up - RFID A Press the white button to start RFID registration process Note: If you already registered your master fingerprint, you must unlock Reach first with your fingerprint and then press the white button within 5 seconds, to enter the master RFID registration process Unit turns on and the top lights all turn red B Place your RFID bracelet onto the top of the RFID sensor like shown All lights will turn green to indicate the RFID has been successfully added C You have now registered the “master
Lock A Place the gun into the holster and push down from the handle. The gun will go down and lock into place A single red light will appear for X seconds to B indicate that the gun has been locked then go out.
Unlock (Biometric/RFID) Biometric A Place your registered fingerprint on the sensor to unlock Lights will turn green to indicate an unlock Lights will flash red to indicate incorrect fingerprint B RFID Tap your RFID bracelet onto the top of the RFID sensor to unlock Lights will turn green to indicate an unlock Lights will flash red to indicate incorrect RFID
Adding New Fingerprints A Unlock Reach with the master fingerprint B Press the white button within 5 seconds of unlocking This timeout that prevents someone from adding a fingerprint when Reach is left unlocked C Reach will enter fingerprint registration mode. The lights will all turn red.
Adding new RFID bracelets/tags A Unlock Reach with the master RFID bracelet B Press the white button within 5 seconds of unlocking This timeout that prevents someone from adding a fingerprint when Reach is left unlocked C Reach will enter RFID registration mode. The lights will all turn red.
Battery life A When you plug Reach into power using the charging mount, A blue light will glow to show a successful connection to power has been made B To check on the battery life Press the white button The blue lights will indicate how much power Reach has (1 blue light = X%, 2 blue lights = X%, 3 blue lights = X%) C Checking battery life (while charging) Press the white button (Explain the UI process here for this)
Soft Reset A If Reach has any software issues, you can do a “soft” reset Hold the white button for X seconds Lights will cycle B *A soft reset will still retain all registered fingerprints and RFID bracelets
Mounting Reach (insert instructions on charging mount, etc) Drilling/bolting the mount Bottom clearance Charging cable Putting Reach into mount Using keys to remove slide Tightening screw with allen key Putting the slide back
Changing out the holster insert A Insert the key into the slot at the bottom of the Reach holstersafe. Turn clockwise and remove the slide by pulling down. B Place the holster insert into the main housing as shown. (The brass locking cam should go into the top hole) C Reassemble the slide by lining it up on the rail and sliding upwards until locked.
Mechanical Key Override If Reach has any software issues, you can do a “soft” reset Hold the white button for X seconds Lights will cycle *A soft reset will still retain all registered fingerprints and RFID bracelets
Troubleshooting (insert answers to common issues) Hard reset Support email
General Maintenance
Firearm safety The Reach® biometric safe or any other firearm storage device cannot take the place of other safety procedures including teaching children of the dangers of firearms. The manufacturers and distributors of the Reach® safe do not recommend, suggest, advise, promote, or otherwise condone the ownership or use of firearms.
General Maintenance Tips and Advice Safety Disclaimers Visit varasafety.
General Maintenance