.0mm HVLP Gravity Feed Touch-Up Spray Gun Instruction Manual 19110 Need help? Call our customer service hotline at 1-800-386-0191 For up-to-date product information, accessories and for a Spanish version of this manual, please visit our website at: www.titan-us.com and click on the literature link or scan the QR Code at left with your smart phone.
INTRODUCTION It is the owner and/or operators responsibility to study all WARNINGS, operating, and maintenance instructions contained on the product label and instruction manual prior to operation of this product. The owner/operator shall retain product instructions for future reference. The owner and/or operator are responsible for maintenance, maintaining all decals or warning labels and while in use, maintaining the unit in good working order.
IMPORTANT SAFETY RULES FOR ALL SPRAY GUNS SAVE THESE INSTRUCTIONS Read and understand all instructions. Failure to follow all instructions included with this product could result in serious personal injury and/or property damage. Follow all local electrical and safety codes as well as in the United States, the National Electrical Codes (NEC), the Occupational Safety and Health Act (OSHA), and the American National Standards Institute (ANSI).
WORK AREA SAFETY INTRODUCTION Before disassembly or removal of any part of gun or attached components, shut off air supply to gun, shut off air compressor, release pressure from spray gun by depressing trigger, and disconnect power source. NEVER assume system pressure is zero. TO AVOID CREATING AN EXPLOSIVE ATMOSHPHERE, WORK ONLY IN WELL VENTILATED AREAS. USE OF A FACE MASK IS RECOMMENDED TO PREVENT INHALATION OF TOXIC MATERIAL. 1. Keep your work area clean and well lit.
TYPE OF SPRAY GUN HOOKUPS SIPHON FEED CUP HOOKUP Air pressure for atomization is controlled by the regulator on the air source. The amount of fluid is adjusted by the fluid control knob on the gun, the paint viscosity, and the air pressure. The siphon cup must be vented to the atmosphere. PRESSURE FEED CUP HOOKUP Air pressure for atomization is controlled by the regulator on the air source. The fluid pressure is set by adjusting the cup regulator.
PREPARATION FOR SPRAYING DO NOT ATTEMPT TO UNCLOG (BACK FLUSH) SPRAY GUN BY SQUEEZING TRIGGER WHILE HOLDING FINGER IN FRONT OF FLUID NOZZLE. Pressure may vary according to viscosity of material used. Maximum working pressure of this gun is 100 psi. DO NOT EXCEED PRESSURE LIMIT OF GUN OR ANY COMPONENT IN THE SYSTEM. Prior to daily operation, make certain that all connections and fittings are secure. Check hose and all connections for weak or work conditions that could render the system unsafe.
PATTERN ADJUSTMENTS FOR PRESSURE HOOKUPS 1) Adjust air pressure to the spray gun according to the recommendations supplied by the spray material manufacturer. This air pressure is typically between 40 to 60 psi for conventional spray guns. Adjust air pressure with the trigger pulled and the air control knob (if applicable) fully open. 2) The width of the “fan spray” is controlled by the pattern control knob. Turn knob counterclockwise to increase the width of the fan spray pattern.
5) After using water to clean out water based paints or materials, spray mineral spirits through the gun to prevent corrosion. 6) Lubricate gun after cleaning using light machine oil. Never use lubricants containing silicone as these lubricants can cause finish defects. Apply light machine oil to: fluid needle packing, air valve packing, side port control packing and trigger point. Coat fluid control spring and all threaded connections with petroleum jelly prior to storage.
TROUBLESHOOTING Problem Encountered Possible Cause TROUBLESHOOTING (Continued) Corrective Action Heavy top or bottom pattern Horn holes plugged. Obstruction on top or bottom of fluid tip. Cap and/or tip seat dirty. Clean. Ream with non-metallic point. Clean. Clean. Heavy right or left side pattern Left or right side horn holes plugged. Dirt on left or right side of fluid tip. Clean. Ream with non-metallic point. Clean.
ITEM 19110 - PARTS BREAKDOWN HVLP GRAVITY FEED SPRAY GUN TIP SIZE APPLICATION GUIDE Tip Size 19 2 0 18 21 Touch-Up Gun 22 1.0 23 1.3 1.4 25 11 12 13 14 15 16 17 9 8 7 6 5 4 27 2 1 28 2 9 30 A good all-purpose tip suitable for general materials including single stages, base coats, water based coatings, clear coats. This larger tip works well with thicker clear materials. A versatile tip for base coats and single stages. Potential risk of orange peel if used to spray clear coats.
90 DAY LIMITED WARRANTY Star Asia-USA, LLC (hereinafter “seller”) warrants to the original purchaser only, that this product will be free from defects in material or workmanship for a period of 90 days from date of purchase for home domestic use. Warranty Performance Warranty coverage is conditioned upon purchaser furnishing seller or its authorized service center with adequate written proof of the original purchase date.
