Digtal voice recoder Digital voice recorder manual Before using product please read the manual carefully 1
Digtal voice recoder Cautions 1.Children are forbidden to play the recorder alone, and do not fall and collide with hard objects, otherwise it may cause data loss or other hardware damage of the recorder. 2.Do not clean the recorder with chemical reagents or cleaning reagents, which will damage the surface of the recorder and corrode it. 3.It is recommended not to use this recorder when driving a motor vehicle or riding a bicycle. Please ensure driving safety. 4.
Digtal voice recoder 6.It is forbidden to pull out the power supply with wet hands to prevent electric shock. 7.Please understand the changes due to the performance and function of this product without prior notice. 8.If the actual settings and usage of this product are inconsistent with this manual due to the upgrade of firmware program, please contact the local distributor.
Digtal voice recoder TIPS: This picture just for reference, and the shape is subject to the physical object.
Digtal voice recoder 1. Power switch: turn on recording/turn off to save recording 2. Indicator hole/sound source input hole 3. USB port/headphone jack 4. Volume up key "+": Short press to increase the volume 5. Volume down key "—": Short press to decrease the volume 6. Play button : short press to play/pause 7. Previous song key : Short press to switch to the previous song 8.
Digtal voice recoder Indicator light description: 1.Recording: the red indicator flashes 3 times 2.Play: Blue lights flashing 3.Standby: the blue indicator is always on 4.Charging: When charging, the red indicator flashes (the full-charge Greenlight is always on ) 5.Low power: the red Indicator flashes quickly for about 10 seconds and then automatically shuts down Turn on 1.When the headset is not plugged in, and the switch was on the “OFF”.
Digtal voice recoder Toggle the switch to the“ON”to turn on the recorder and start recording (the indicator light turns from purple light to red light and flashes 3 times and turns off). Turn off 1.In the recording or playback state, toggle the switch to the “OFF”, (the purple light flashes once and turns off) to save the recording and shut down. Recording 1.
Digtal voice recoder light turns from purple light to red light and flashes 3 times and turns off). Note: You can't speak to the microphone near the recorder during recording, so the recorded voice will pop. It is best to keep the voice more than 30 centimeters away for clearer. Save 1.With no earphones plugged in, toggle the switch to the “OFF”, (the purple light flashes once and turns off) to save the recording and turn it off. 2.
Digtal voice recoder current recording file and play it. 3.The 8-hour recording is automatically saved as a file to avoid the loss of the file when it is too large. 4.When the battery is low, the recorder automatically saves the recording and automatically shuts down. Play 1. Computer playback: insert the USB data cable to connect to the computer, enter the drive letter of the recorder memory, find the recording file, and play it on the computer.
Digtal voice recoder Player) 2. Play on the recorder: Make sure that the switch is turned to "OFF", then insert the earphone, and then push the switch to "ON", the recorder will turn on and automatically play the current recording file. (The blue light flashes at this time). The function definition of the wire control button: (short press for 1 second, long press for 3 seconds) 3. Short press the "Play" button to play/pause.
Digtal voice recoder 4. Short press " " button to play the previous song, short press " " button to play the next song. 5. Short press the "+" key to increase the volume, short press the "-" key to decrease the volume. ● Set time/recording sensitivity adjustment/voice activation setting/recording bit rate 1. Ensure that the switch in the "OFF" state, insert one end of the USB cable into the recorder and the other end into the USB port of the computer.
Digtal voice recoder will recognize it and pop up the "USB DISK" drive letter. 2. Double-click to open "USB DISK", find "RECSET.txt" and double-click to open, as shown below: 3. Time means the date and time setting: the numbers represent from left to right (year, month, day, hour, minute, second), and the format of 14 digits must be retained when setting.
Digtal voice recoder use Settime to synchronize time 4. Gain means recording sensitivity adjustment: Gain: the 0 behind can be replaced with any number from 0 to 7, and the larger the number, the stronger the sensitivity, the louder the recording sound. Note: Adjust carefully sound. Advice:5 5.
Digtal voice recoder As shown in the figure above, the 0 behind Vor: means that the voice activation function is disabled. To enable this function, please replace 0 with any number from 1 to 10. Please note: the smaller the number to be replaced, the louder the sound to trigger voice activation, and the larger the number to be replaced, the desired sound the smaller. Advice:0 5.
Digtal voice recoder means 128Kbps, 3 means 192Kbps, 4 means 384Kbps. (The larger the number set here, the recording voice will be fuller, but the recording file will also be larger. Advice:3 6. Part represents recording segment: 0-240 minutes adjustable, 0 represents 8 hours off by default. Advice:0 (Change any parameter of this text, be sure to save the text, and it will take effect after restarting the recorder) Note: This parameter is the factory default best setting.
Digtal voice recoder carefully. If you need to modify it, please backup this file to prevent errors. ● Time tool to synchronize system time 1. In the shutdown state, insert one end of the USB cable into the recorder and the other end into the computer. After a few seconds, the computer will recognize it and pop up the "USB DISK" drive letter. 2. Double-click the "USB DISK" drive letter to enter, find the "Settime" folder and open it. 3. Find "SetDigitRecorderTm.
Digtal voice recoder double-click to run it. 4. At this time, a small window appears, click "SetTime" and the system will automatically pop up the computer synchronization time, click "OK" directly. 5. The time setting of the recorder is completed, please use the correct method to remove the "USB DISK".
Digtal voice recoder the recorder, the system time will automatically be restored to the factory time. Please reconnect it to the computer to synchronize to the correct time! (This time can be used as the recording reference time, that is, the time stamp is generated on the recording file) ● Connect to computer 1.In the shutdown state, insert one end of the USB cable into the USB port of the recorder and the other end into the USB port of the computer.
Digtal voice recoder Note: In order to protect your important files, you need to connect to a computer to delete, manage, record or download MP3 files. If the WAV format is not supported, please download another music player to play. 2.After connecting to the computer, the red light flashes, and data can be transmitted. Tips: a. Please use the normal method to remove the "USB DISK" to prevent data loss. b.
Digtal voice recoder or the "USB DISK" logo still does not pop up after a few seconds, please plug it in again or change another USB port on the computer. If it still fails to connect normally, 1. Please check if your computer is using a bad extension cable or USB cable. 2. replace the data cable.
Digtal voice recoder Recharge 1)Insert one end of the USB cable into the USB port of the recorder and the other end into the USB port of the charger. The indicator light flashes red when charging, and the charging time is generally about 2 hours to fully charge.When the red light is on, it means that the battery is fully charged.
Digtal voice recoder Problem Possible Causes Solution Appear 1.Check if the battery is 1.Charging Unable to Record dead in a timely manner when the power is 2.Whether the number off of recording files exce 2.Delete extra audio files to eds 999 Storage space ensure adequate memory is full 1. Play headphones and 1. Charge in time check if the battery is 2. Download the music Play Cannot Play exhausted er, such as: Windows Media Recording 2.
Digtal voice recoder 1. Check whether the 1. Replace the Phone's Data USB data cable is nor Cable or USB Port (2.0). After the USB mal (part of the data c 2. Use Windows Computer to is inserted, able can only charge, Check whether the Driver is removable but cannot transmit da Normal. disk drive ta) letter cannot 2. Check whether the c inserts nothing. Check for be found omputer drive is norm the presence of the sign al "Safe Remove Hardware and 3. If the Windows system 3.
Digtal voice recoder after-sales service electronic products in time. may 3C have trouble, please understand, and the After-sales Technical Service Team will solve in 24 hours.
Digtal voice recoder recorder's storage capacity, not the time that the battery can continuously record. (For reference only, actual test may have deviation) ● Technical specifications Dimensions 70*23*8mm(The actual product shall prevail) USB interface USB 2.0 High Speed Built-in memory 8GB – 128GB Battery 3.
Digtal voice recoder Music format Body weight MP3/WMA/WAV 34g(The actual product shall pre vail) Pay attention: 1. Please use Windows Media Player to play WAV format. 2. If the connected computer cannot be recognized, you do not need to return the goods, contact customer service Statement: Users must back up their data during use.
Digtal voice recoder hardware, battery product maintenance, replacement unexpected situations, or and other is not responsible for it. Liability for other indirect losses caused by this. At the same time, we cannot control the misunderstandings that users may cause in this manual. Therefore, the company will not be responsible for accidental damage that may occur during the use of this manual, and will not be responsible for third-party claims caused by the use of the product.
Digtal voice recoder capacity space, and it is normal that there is a slight difference from the nominal capacity) This product is only used for learning and training. Please strictly abide by the relevant national laws and do not do any illegal acts. The company does not make any commitments and responsibility for the consequences of illegal acts.